Grizzly Industrial G6050 - Manual

Page 2 - NOTICE; Safety Instructions For Pneumatic Tools; SAFETY

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, ifnot avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, ifnot avoided, COULD result in death or serious injury. Indicates a...

Page 4 - Basic Nailer Safety

G6050 Round Head Framing Nailer Kit -3 - Operating this nailer can propelobjects into the air, causing immedi-ate eye damage. To protect yourself,always wear American NationalStandards Institute (ANSI) approvedsafety glasses or goggles when oper-ating this equipment. In addition, thisnailer discharg...

Page 5 - INTRODUCTION; Commentary

G6050 Round Head Framing Nailer Kit -4 - INTRODUCTION Commentary Most important, we stand behind our tools.If you have any service questions or partsrequests, please call or write us at thelocation listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663...

Page 6 - Compressed Air System

G6050 Round Head Framing Nailer Kit -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanicaldevice that can fail. Never rely on thesafety yoke mechanism as an excuseto point the nailer at yourself or anybystanders. Serious injury may occur. Exceeding the maximum permissibleop...

Page 7 - OPERATION; Loading Nailer; Single/Bump Fire Mode

G6050 Round Head Framing Nailer Kit -6 - OPERATION Loading Nailer To load your nailer: 1. Disconnect the air supply from thenailer! 2. Pull the magazine pusher all the wayback until it locks in place. 3. Place a stick of nails into the maga-zine as shown in Figure 1 . Make sure the pointed ends of t...

Page 9 - Clearing Jammed Nails

G6050 Round Head Framing Nailer Kit -8 - Always disconnect air from nailerwhenever clearing a jammed nail! Clearing Jammed Nails The most frequent situation with any typeof nailer is a nail jam. A jammed nail mustbe cleared before using the nailer again.The two places where a nail can getjammed are ...

Page 10 - Cleaning Nailer

G6050 Round Head Framing Nailer Kit -9 - Cleaning Nailer Use a good solvent to clean the noseassembly of the nailer. Always be sure thatthe nailer is dry before using it again. Do not allow dust, chips, sand, etc. into theair connectors or into the body of the nail-er; this may result in leaks and d...

Page 14 - TROUBLESHOOTING; PROBLEM

TROUBLESHOOTING Air leaking at trigger valvearea. Air leaking between hous-ing and hose. Air leaking between hous-ing and cap assembly. Tool skips nails while dis-charging. Tool runs slowly or has aloss of power. Fasteners frequently jamthe nailer. Nailer does not fire. 1. O-rings must be replaced &...

Page 15 - WARRANTY AND RETURNS

G6050 Round Head Framing Nailer Kit -14 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directlyor indirectly to misuse, abuse, negligence, accidents, repairs or alterat...

Page 16 - WARRANTY CARD

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # _______________Serial#_______________...

Page 17 - Place

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here

Grizzly Industrial G6050 - Manual

Table of Contents:

Summary

Other Grizzly Industrial Models