Grizzly Industrial G0574 - Manual
Grizzly Industrial G0574 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – Table Of Contents
- Page 6 – Safety Instructions For Power Tools
- Page 7 – Additional Safety Instructions For Sanders
- Page 8 – SECTION 2: CIRCUIT REQUIREMENTS; Operation; Circuit Load; Grounding
- Page 10 – Commentary; SECTION 3: GENERAL INFORMATION
- Page 11 – NOTICE
- Page 12 – Site Considerations
- Page 14 – Working Table
- Page 16 – Quick Release Lever; Miter Body
- Page 17 – Auxiliary Table; Dust Hood
- Page 19 – Belt Tracking; SECTION 5: ADJUSTMENTS
- Page 20 – Table Tilt; Table Height
- Page 22 – SECTION 6: OPERATIONS
- Page 23 – Horizontal Sanding
- Page 24 – SECTION 7: MAINTENANCE; Lubrication; General
- Page 26 – GRIZZLY MODEL G1140 HEAVY DUTY EDGE SANDER; MACHINE DATA
- Page 30 – WARRANTY AND RETURNS
- Page 31 – WARRANTY CARD
INTRODUCTION
The Model G0574 Radiusing Sander is based
on the Model G1140 Edge Sander with the
addition of the radiusing attachment. Refer to the
G1140 Edge Sander manual for the sanding unit
assembly instructions and refer to the included
G0577 Radiusing Attachment manual for
radiusing attachment installation instructions. The
Model G0574 DOES NOT include the work table,
auxiliary table, and miter body listed in the manual
of the G1140. These parts are unnecessary
when the radiusing attachment is installed. The
inventory for the G0574 is as follows:
Model G0574 Parts:
•
Sanding Unit ............................................... 1
•
Quick Release Lever .................................. 1
•
Dust Port .................................................... 1
•
6'' X 80'' Sanding Belt ................................ 1
•
Back Stop ................................................... 1
•
Feet ............................................................ 4
•
Long Support Bracket ................................ 1
•
Short Support Bracket ................................ 1
•
Guide Rail A ............................................... 2
•
Guide Rail B ............................................... 4
•
Radius Control Swing Arm Assembly ........ 1
•
Horizontal Adjustment Tubes ..................... 2
•
Locking Plate A .......................................... 2
•
Locking Plate B .......................................... 4
•
Brace .......................................................... 1
•
Height Adjustment Arms ............................ 2
•
Idler Roller Cover ....................................... 1
MANUAL INSERT
Model G0574
Radiusing Sander
Figure 1.
Model G0574.
COPYRIGHT © MAY, 2005. BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#EW7254 PRINTED IN TAIWAN
Model G0574 Hardware Bag:
—Shim ....................................................... 1
—Hex Bolt
5
⁄
16
"-18 x 2½" ............................. 3
—Hex Bolt
3
⁄
8
"-16 x 1" ................................. 3
—Flat Washer
3
⁄
8
" ......................................11
—Flat Washer
5
⁄
16
" ...................................... 6
—Hex Nut
5
⁄
16
"-18 ....................................... 3
—Hex Bolt
3
⁄
8
"-16 x 2 .................................. 2
—Hex Nut
3
⁄
8
"-16 ......................................... 2
—
7
⁄
32
" Hex Wrench ...................................... 1
—12-14mm Open End Wrench ................... 1
—2mm Hex Wrench ................................... 1
—Phillips
®
Hd Screw 10-24 X 3/4'' ............. 4
NOTICE
When ordering parts for the Model G0574 Radiusing Sander, refer to the G1140 manual for sanding unit
components, and refer to the G0577 manual for radiusing attachment components.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
G1140 Edge Sander -C- Table Of Contents PAGE 1. SAFETY RULES SAFETY RULES FOR POWER TOOLS ................................................................................1-2SAFETY RULES FOR SANDERS ............................................................................................3 2. CIRCU...
-2- G1140 Edge Sander 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi-tion. Conductor size should be in accor-dance with the chart below. The amperagerating should be listed on the motor or toolnameplate. An undersized cord will cause adrop in line voltage resulting in ...
G1140 Edge Sander -3- 6. TURN OFF THE SANDER WHEN NOTIN USE. Never leave a machine running unattended. 7. DO NOT stand directly in line with sanding accessories when turning the machine on. 8. DO NOT force the workpiece against the belt during operation. Firmly grasp theworkpiece in both hands and e...
