Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................................................................................................... 2 Foreword .....................................................................................................................................
Page 4 - Foreword; INTRODUCTION; Contact Info
-2- Model G0477 15" Planer/Moulder If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or pa...
Page 5 - Machine Data Sheet
Model G0477 15" Planer/Moulder -3- ������������������������������ ������������������������������������������������������������������������������������������ ������������� ����� ������������������� � �������������������������������������������������������������������������������������������������...
Page 7 - Identification
Model G0477 15" Planer/Moulder -5- Figure 1. G0477 Component and Control Identification. A. Infeed/Outfeed Roller Height Adjuster B. ON/OFF Switch C. Circuit Breaker Reset Button D. Return Rollers E. Headstock Height Hand Crank F. Cutterhead Lock G. Tool Storage H. Depth-of-cut Gauge I. Preset D...
Page 8 - NOTICE; Safety Instructions for Machinery
-6- Model G0477 15" Planer/Moulder 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair cov...
Page 10 - Additional Safety for Planer/Moulders
-8- Model G0477 15" Planer/Moulder Additional Safety for Planer/Moulders No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Fa...
Page 11 - SECTION 2: CIRCUIT REQUIREMENTS
Model G0477 15" Planer/Moulder -9- Figure 2. Typical type 5-15 plug and receptacle. Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. 110V Op...
Page 12 - Set Up Safety; Items Needed for; Unpacking
-10- Model G0477 15" Planer/Moulder Wear safety glasses dur- ing the entire set up pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Set Up Safety SECTIO...
Page 13 - Inventory
Model G0477 15" Planer/Moulder -11- Inventory After all the parts have been removed from the two boxes, you should have the following items: Inventory (Figure 3) Qty A. Long Frames .............................................. 2 B. Short Frames .............................................. 2 C...
Page 14 - Site Considerations; Clean Up
-12- Model G0477 15" Planer/Moulder Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some floors may require additional reinforcement to support both the machine and operator. Working Clearances Consider existing and anticipated needs, size ...
Page 15 - Stand Assembly
Model G0477 15" Planer/Moulder -13- Stand Assembly The stand for the Model G0477 must be assem-bled before the planer/moulder can be mounted on it. It may be helpful to refer to the Stand Breakdown on Page 35 during this procedure. Components and Hardware Needed: Qty Notched Legs* .................
Page 17 - Test Run; Crank Handle
Model G0477 15" Planer/Moulder -15- Test Run Once the assembly is complete, test run your machine to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooting on P...
Page 18 - Operation Safety; SECTION 4: OPERATIONS; Safety Switch Key; Basic Operation
-16- Model G0477 15" Planer/Moulder Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. Loose hair and cloth- ing could get caught in machinery and ...
Page 19 - Operation Tips
Model G0477 15" Planer/Moulder -17- Note: If the cut is too heavy and bogs down the planer/moulder, turn the planer/moulder OFF immediately, allow it to come to a com- plete stop, remove the workpiece, and repeat Steps 3–5 . 6. Measure your workpiece thickness and adjust the headstock height as ...
Page 20 - Preset Thickness
-18- Model G0477 15" Planer/Moulder Headstock Height Adjustment The headstock height can be adjusted via the manual crank handle (used for fine adjustments) or by the power adjustment lever (used for larger headstock movements). The Model G0477 features a height scale (in both inches and mil-lim...
Page 22 - Moulding Knives
-20- Model G0477 15" Planer/Moulder Moulding Knives Tools Needed: Qty Wrench 8mm ..................................................... 1 The G0477 has two moulding knife slots. Each slot can accommodate two different moulding knives at the same time. However, both moulding knife slots must be se...
Page 25 - SECTION 5: ACCESSORIES
Model G0477 15" Planer/Moulder -23- G4520–G4564 Moulding Knives Select from this terrific assortment of casing, baseboard, crown moulding and detail cutters. Knives come in sets of three. SECTION 5: ACCESSORIES G4561 G4548 G4564 G4550 G4549 G4541 G4522 G4521 G4547 G4540 G4546 G4559 G4563 G4562 G...
Page 26 - SECTION 6: MAINTENANCE; Schedule
-24- Model G0477 15" Planer/Moulder Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. SECTION 6: MAINTENANCE For optimum performance from your machine, follow this maintenance schedule and refer to any specific instr...
Page 27 - Troubleshooting Guide
Model G0477 15" Planer/Moulder -25- Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. SECTION 7: SERVICE Troub...
Page 30 - Changing Belts; Chain Tension and
-28- Model G0477 15" Planer/Moulder Changing Belts Tools Needed: Qty Hex Wrench 4mm .............................................. 1Hex Wrench 5mm .............................................. 1 The Model G0477 features two ribbed belts, shown in Figure 26 , that are generally good for the life...
Page 31 - Changing Motor
Model G0477 15" Planer/Moulder -29- NOTICE DO NOT let the chain fall off the sprock- ets—returning it to its proper location with- out changing the table adjustments can be very difficult. Figure 27. Underside of table. Cap Screws Idler Bracket 5. For each corner of the headstock that needs to b...
Page 32 - Electrical Components
-30- Model G0477 15" Planer/Moulder Electrical Components Figure 29. Rear of power switch and circuit breaker (switch assembly inverted). Power Switch Circuit Breaker
Page 33 - Wiring Diagram
Model G0477 15" Planer/Moulder -31- ����� ����� ����� ��������� �� �� �� ������������������������������������������� ������� ������� ���������� ����� ������ ���������� ������ ������� ��������� ����������������� � � ������ �� �� ����� ������ ������ �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� Wir...
Page 35 - G0477 Table and Base Breakdown
Model G0477 15" Planer/Moulder -33- � � � � � �� � �� � � � ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ...
Page 39 - Parts List
Model G0477 15" Planer/Moulder -37- REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0477001 CAP (LEFT) 51 PR05M EXT RETAINING RING 15MM 2 PSB04M CAP SCREW M6-1 X 10 52 P0477052 CHAIN 3 P0477003 ROLLER 53 PSB152M CAP SCREW M5-.8 X 65 4 P0477004 SPECIAL CAP SCREW M8-1.25 X 72 54 P0477054 OUTSIDE ...
Page 43 - WARRANTY AND RETURNS
Model G0477 15" Planer/Moulder -41- Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterati...
