Grizzly Industrial G0443 - Manual

-4- Model g0443 (Mfg. since 11/09) The information contained herein is deemed accurate as of 3/27/2012 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2 Model G0443 MACHI...

-6- Model g0443 (Mfg. since 11/09) For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tanc...

-8- Model g0443 (Mfg. since 11/09) ­­ INTENDED USE. ­ This­ dust­ collector­ is­ only­ intended­ for­ collecting­ wood­ dust­ and­ chips­ from­woodworking­ machines.­ DO­ NOT­ use­ this­ dust­collector­ to­ collect­ metal,­ dirt,­ pebbles,­ drywall,­asbestos,­ lead­ paint,­ silica,­ liquids,­ aeroso...

Model g0443 (Mfg. since 11/09) -9- SECTiON 2: POWER SUPPLY availability Before installing the machine, consider the avail-ability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. To minimize t...

-10- Model g0443 (Mfg. since 11/09) Grounding & Plug Requirements figure 2. typical l5-30 plug and receptacle. Grounding Prong is Hooked Hot Neutral L5-30 GROUNDED LOCKING RECEPTACLE L5-30 LOCKING PLUG This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding r...

Model g0443 (Mfg. since 11/09) -11- G0443 Conversion to 220v Operation Converting the Model g0443 from 110V to 220V operation consists of: 1) replacing the 110V remote magnetic switch with the 220V switch, 2) re-wiring the motor, and 3) installing a neMa 6-15 plug and receptacle. purchase the Model ...

-12- Model g0443 (Mfg. since 11/09) SECTiON 3: SETUP This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! This machine and its com- ponents are very heavy. Get lifting hel...

Model g0443 (Mfg. since 11/09) -13- inventory The following is a description of the main compo-nents shipped with your machine. Lay the compo-nents out to inventory them. If any non-proprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, re...

-14- Model G0443 (Mfg. Since 11/09) Site Considerations Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heav...

Model g0443 (Mfg. since 11/09) -15- Before mounting, make sure to situate the dust collector away from any open flames or potential ignition sources, as fine dust can easily ignite. if mounting the dust collector to a wood framed wall, you must build and install the wall mount-ing boards described b...

-16- Model g0443 (Mfg. since 11/09) 3. tighten the 1 ⁄ 2 " lag bolts into the mounting locations so they do not project more than 1 ⁄ 2 " from the mounting board to the top of the head, but leave them out enough to slide the housing over. this will prepare the mounting board for the mounting...

Model g0443 (Mfg. since 11/09) -17- assembly To assemble the dust collector: 1. attach the wall mounting bracket to the motor/ blower housing with the provided (6) 3 ⁄ 8 "-16 x 1" hex bolts, (12) 3 ⁄ 8 " flat washers, and (6) 3 ⁄ 8 "-16 hex nuts. refer to the parts breakdown diagram ...

-22- Model g0443 (Mfg. since 11/09) 23. Fit the plastic canister collection bag over the bottom of the canister filter and clamp in place with the metal bag clamp, as shown in figure 30. figure 30. plastic collection bag clamped in place under filter. Bag Clamp 24. Mount the switch on the funnel wit...

Model g0443 (Mfg. since 11/09) -23- Test Run once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. if, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then ...

-24- Model g0443 (Mfg. since 11/09) SECTiON 4: DESiGNiNG THE SYSTEM General Duct Material You have many choices regarding main line and branch line duct material. For best results, use metal duct for the main line and branch lines, then use short lengths of flexible hose to connect each machine to t...

Model g0443 (Mfg. since 11/09) -25- There are a number of options when it comes to metal duct, but metal duct that is specially manu-factured for dust collection is the best choice. When selecting your metal duct, choose high quality metal duct with smooth welded internal seams that will minimize ai...

-26- Model g0443 (Mfg. since 11/09) System Design Step 3. Sketch a basic Duct Layout Step 1. Decide Who Will Design For most small-to-medium sized shops, you can design and build the dust collection system your-self without hiring engineers or consultants. We have included some basic information her...

Model g0443 (Mfg. since 11/09) -27- 3. directional changes should be kept to a mini- mum. the more directional change fittings you use directly increases the overall resis-tance to airflow. 4. gradual directional changes are more effi- cient than sudden directional changes (i.e. use the largest corn...

-28- Model g0443 (Mfg. since 11/09) Determining Main Line Duct Size figure 41. Main line size labeled on sketch. 395 395 614 790 395 220 98 Dust Collector 5" 6" 7" Table Saw Planer/ Moulder Miter Saw Jointer Sander Planer Shaper figure 42. Branch line duct sizes labeled. 395 395 614 790 ...

-30- Model g0443 (Mfg. since 11/09) figure 45. additional factors affecting static pressure. figure 46. totaling static pressure numbers. Main Line 6" Rigid Pipe (0.037) at 20' ................ 0.740 Branch Line 4" Rigid Pipe (0.075) at 10' ................ 0.750 4" Flex Pipe (0.28) at 5...

Model g0443 (Mfg. since 11/09) -31- the airflow test probe is located 1.5x duct diameter upstream from the air inlet. test pipe length is a minimum of 10x duct diameter. G0443 Performance Curve 2500225020001750150012501000 750500250 0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 1025 CfM STaTiC...

-32- Model g0443 (Mfg. since 11/09) System Grounding since plastic hose is abundant, relatively inex-pensive, easily assembled and air tight, it is a very popular material for conveying dust from woodworking machines to the dust collector. we recommend using flexible hose (flex-hose) to connect the ...

Model g0443 (Mfg. since 11/09) -33- Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. always wear safety glasses, a respirator, and hearing protection when operating this machine. SECTiON 5: OPERaTiONS NOTICE if you have never used this type of...

-34- Model g0443 (Mfg. since 11/09) SECTiON 6: aCCESSORiES aCCessories Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machin...

-36- Model g0443 (Mfg. since 11/09) SECTiON 7: MaiNTENaNCE always disconnect power to the machine before performing maintenance. failure to do this may result in serious person- al injury. Emptying Drum empty the collection drum when it is no more than 3 ⁄ 4 full. if the drum is overfilled, dust wil...

Model g0443 (Mfg. since 11/09) -37- Removing /Replacing filter the filter for canister filter assemblies manufac-tured since november, 2009, can be removed from the assembly so that it can be replaced or rinsed off (see the instructions in the next subsec-tion). removing/installing the filter requir...

Model g0443 (Mfg. since 11/09) -39- Review the troubleshooting and procedures in this section if a problem develops with your machine. If you need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. Note: Please gather the serial number and manufactur...

Model g0443 (Mfg. since 11/09) -41- SHOCK HAZARD. Working on wiring that is con- nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before...

Model g0443 (Mfg. since 11/09) -45- Ref Part # Description Ref Part # Description 1 P0443001 MOTOR 1.5HP 110/220V 1PH 34 P0443016 FOAM TAPE 3 X 6 X 1800MM 1-1 P0443001-1 MOTOR FAN COVER 35 P0443035 INTAKE CYCLINDER 9" 1-2 P0443001-2 MOTOR FAN 36 PW07 FLAT WASHER 5/16 1-3 PC300B S CAPACITOR 300MF...

-46- Model g0443 (Mfg. since 11/09) Labels Ref Part # Description Ref Part # Description 64 P0443064 MOTOR SPEC LABEL 69 P0442097 RETURN RED HANDLE LABEL 65 P0442093 MOTOR WARNING LABEL 70 PLABEL-14 ELECTRICITY 1.4W X 1.2H 66 PLABEL-82 GLASSES/RESPIRATOR DC LABEL 71 P0443071 MACHINE ID LABEL 67 PLAB...

Model g0443 (Mfg. since 11/09) -47- C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zi...

Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!