Greenheck SMD-401 - Manual
Greenheck SMD-401 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Pressure Drop Data; Damper Size; AMCA Test Figures; Illustrates a fully ducted damper. This
- Page 3 – outside of the damper sideplate or sleeve. The “S” dimen; Application Data; Damper Sideplate and Sleeve Dimensional Data; Sleeve; Actuator
- Page 4 – Transitioned Damper; or; Damper Sizing Information; Specifications; TYPE R
Model SMD-401 meets the requirements for smoke
dampers established by:
National Fire Protection Association
NFPA Standards 92A, 92B, 101 & 105
IBC International Building Codes
New York City
(MEA listing #260-91-M)
California State Fire Marshall
Listing#: 3230-0981:108 (smoke)
“UL CLASSIFIED (see complete marking on
product)”
“UL CLASSIFIED to Canadian safety standards
(see complete marking on product)”
Standard 555S (Listing #R13317)
APPLICATION
Model SMD-401 is a class I leakage rated smoke damper. High strength,
streamlined extruded airfoil blades insure lowest resistance to airflow in
HVAC systems with velocities to 3000 fpm (15.2 m/s) and 6 in. wg (1.5
kPa). Model SMD-401 may be installed vertically (with blades running
horizontal) or horizontally and is rated for airflow and leakage in either
direction.
RATINgS
Leakage:
UL 555S leakage class I. Leakage
rated in both directions
Velocity:
Operational rated to 3000 fpm
(15.2 m/s) for sizes up to
48 in. W x 108 in. H or 144 in. H x 36 in. H
(1219mm x 2743mm) or
(3658mm x 914mm) or
2000 fpm (10.2 m/s) for sizes
greater than that. Rating is for
airflow in either direction through
damper.
Temperature:
250°F (121°C) with all actuators.
Maximum Pressure:
6 in. (1.5 kPa)
STANDARD CONSTRUCTION
Frame:
5 in. x 1 in. (127mm x 25mm)
galvanized steel hat channel with
reinforced corners. A low profile
head and sill are used on sizes less
than 17 in. (432mm) high to
maximize free area and
performance.
Blades:
Airfoil shape constructed of heavy
gauge extruded aluminum.
Structural reinforcement through
the entire length.
Seals:
Extruded silicone rubber blade
seals. Flexible stainless steel jamb seals.
Linkage:
Concealed in jamb.
Axles:
1
⁄
2
in. (13mm) dia. plated steel.
Bearings:
Bronze sleeve type
SIzE LIMITATIONS:
Minimum Size:
8 in. W x 8 in. H (203mm x 203mm)
Maximum Size:
Single Section:
48 in. W x 60 in.
(1219mm W x 1524mm H)
Multiple Section:
192 in. W x 72 in. H
(4877mm W x 1829mm H) or
48 in. W x 288 in. H
(1219mm W x 7315mm H) or
384 in. W x 36 in. H
(9754mm W x 914mm H)
Optional Features:
• Galvanized steel sleeves
• Stainless steel bearings
• OCI (Open closed indication switches)
• Electric or pneumatic actuators to accomplish smoke
management and system functions.
• POC retaining angles
• Smoke detector
• Momentary switch
• Transformer
Model SMD-401
Smoke Dampers
Extruded Airfoil Blades
UL 555S Leakage Class I
*W&H dimensions furnished approximately
1
/
4
in. (6mm) undersize.
(Add sleeve thickness for overall sleeved damper dimension)
Right hand drive is shown. Left hand drive is available upon request.
H*
W*
LH
RH
Installation instructions available at www.greeenheck.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Pressure Drop Data SMD-401 This pressure drop testing was conducted in accordance with AMCA Standard 500-D using the three configurations shown. All data has been corrected to represent standard air at a density of .075 lb/ft 3 (1.201 kg/m 3 ). Actual pressure drop found in any HVAC system is a comb...
Space Envelopes Required for Actuators and Accessories Externally mounted actuators always require space outside of the damper sideplate or sleeve. The “S” dimen - sion illustrates the clearance required for various available actuators. On dampers less than 18 in. (457mm) high, actuators may also re...
JO NN JO NN Transitioned Damper Dimensions When a fire/smoke damper is being used in conjunction with round or oval ductwork, the SMD-401 can be supplied in a factory sleeve with round or oval transitions on both ends of the sleeve. Dampers should be ordered to the duct dimensions. Drawings below sh...
