Graco ti8370a - Manual - manualsarea.com

Page 2 - Warnings; Fire and Explosion Hazard; Equipment Misuse Hazard

Warnings 2 Warnings The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these gener...

Page 3 - Electric Shock Hazard; Pressurized Equipment Hazard

Warnings 3 Electric Shock Hazard To reduce the risk of electric shock: • Be sure sprayer is adequately grounded through electrical outlet. • Use only 3-wire, extension cords. • Make sure ground prongs are intact on sprayer and extension cords. Improper installation of grounding plug will result in a...

Page 5 - Component Identification

Component Identification 5 Component Identification 3.5 cfm@40 min. Q M A K E B P J D C H G ti8369a F L N R Item Component Item Component A Pump Hose Outlet J Burp Guard B RotoFlex™ II Pump (inside) K ON/OFF Switch C Texture Spray Gun (Manual 311777) L Power Cord (120V, 15 ft) D Nozzle (2 included, ...

Page 6 - Preparation; Pressure Relief Procedure; Grounding and Electrical Requirements; Additional Required Equipment

Preparation 6 Preparation Pressure Relief Procedure To reduce risk of injury, follow this procedure whenever you see this symbol throughout this manual, Also, perform this procedure whenever you: • Stop spraying • Check or repair any part of this system • Install or clean spray nozzle 1. Turn power ...

Page 7 - Setup; Texture Spraying

Setup 7 Setup Texture Spraying 1. Connect air hose to user-supplied air compressor & material hose (G) to material hose outlets. 2. Connect user supplied air hose to gun. 3. Open air valve. 4. Connect material hose to gun. 5. Install spray nozzle. See Recommended Nozzle Selection Chart, page 10....

Page 9 - Mixing Material

Mixing Material 9 Mixing Material Dry Mix - 40 lb (18 kg) bag. 1. Slowly add one 40 lb. (18 kg) bag of texture material to 5-6 gallons (18.9-22.7 liters) of clean water as instructed on the bag instructions. 2. Agitate to mix, using a half-inch, variable speed drill with mixing paddle, to a smooth, ...

Page 10 - Spray Techniques

Spray Techniques 10 Spray Techniques Recommended Nozzle Selection Chart 1 Control air volume with gun air valve. 2 For more material volume try a larger nozzle. Adjusting the System Sufficient fluid output (volume and pressure) and good atomization is a balance of atomizing air, material thickness/m...

Page 11 - Shutdown and Cleanup; Texture Spraying (5 gallon Material Hopper)

Shutdown and Cleanup 11 Shutdown and Cleanup Texture Spraying (5 gallon Material Hopper) When you have finished spraying: 1. Turn sprayer power switch (K) ON (air compressor can remain OFF). 2. Close gun air valve. 3. Trigger gun into bucket until most of texture mix is pumped out. 4. Fill material ...

Page 12 - Troubleshooting

Troubleshooting 12 Troubleshooting Problem Cause Solution Sprayer won’t run Power switch not on Turn switch on. No power at wall outlet Check outlet by plugging in another appliance. If appliance does not work, try another outlet. Wrong size generator Use a 3500 watt or larger generator. Refer to Ge...

Page 14 - Technical Data

Technical Data 14 Technical Data Main Unit Power Requirements . . . . . . . . . . . . . . . . . . . . 120 Vac, 60 Hz, 15A, 1 phaseMaximum Fluid Working Pressure . . . . . . . . . . . . . . . . . . 50 psi, (3.5 bar)Maximum Air Working Pressure . . . . . . . . . . . . . . . . . . . . 100 psi (7.0 bar)...

Page 15 - Notes

Page 16 - Graco Warranty

Graco Warranty 16 Graco Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or lim...

Graco ti8370a - Manual

Table of Contents:

Summary

Other Graco Models