Graco SimpleSwitch User Manual

Page 2 - This product can be used in the following modes:

Highchair Feeding Booster attached to chair This product can be used in the following modes:

Page 5 - Check; BEFORE; Parts list

This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. No tools required. Parts list !,,-/$%,3 2X #%24!).-/$%,3 2X 2X

Page 6 - To Attach Front Legs

To Attach Front Legs 1 Grab leg with collar and insert it ﬁrmly into openings in footrest as shown.Line up buttons and guide with channels in opening. 2X 2X 2 Push front legs up into footrest until the collars stop them. collar

Page 8 - To Attach Rear Legs

5 Insert rear legs into bottom of seat as shown. SNAP! To Attach Rear Legs

Page 9 - To Remove Legs

To remove front legs, press button on side of seat and pull leg out a little.NOTE: DO NOT pull leg out completely until you have pressed button on the other side of seat to release the other leg. To remove rear legs, press buttons on side of seat as shown. 6 To Remove Legs 7 8

Page 10 - Seat Back; DO NOT

Seat Back 9 Insert seat back into base of infant seat. NOTE: Make sure straps DO NOT get caught between seat bottom and back.

Page 11 - CHECK

Turn two pieces over while holding the seat back in place and CHECK to make sure the seat back is in the seat base before inserting pins into place. Insert pins through seat hinge past the tabs. 11 2X SNAP! 10 Squeeze handle to allow rods to drop into holes.

Page 12 - Attaching Seat Pad

Attaching Seat Pad Pull waist straps through openings in seat pad. 12 13 Insert straps on back of seat pad into slots in seat back as shown.

Page 15 - Head support and Harness covers

20 Pull waist straps through openings in head support. 19 Place head support on top of seat pad. Head support and Harness covers (On certain models) Never use this head support on any other product.

Page 17 - To Use Tray; OR

To Use Tray 23 Squeeze release levers on each side of tray, place tray on seat, and snap into side tray locks. SNAP! 24 To release push button on front of tray. 25 OR To release squeeze release levers on each side of tray and lift off.

Page 18 - Tray Cover

Tray Cover 26 Attach tray cover by pushing it down on the tray. To remove pull up on the back of the tray. 27 SNAP! Dishwasher safe.

Page 19 - To Recline Seat; WARNING

To Recline Seat Squeeze handle on back of seat and push down or pull up to adjust. 28 29 WARNING DO NOT adjust the seat recline with the child in it. There are 3 recline positions. I

Page 23 - Using as Feeding Booster

Using as Feeding Booster In order to use as feeding booster you will need to remove all of the legs. See page 12 to remove the front and rear legs. Slide 4 strap doors over leg holes in seat to access straps. 40 Pull straps out from compartments in bottom of seat. 41

Page 26 - To Remove Feeding Booster from Chair; FALL HAZARD

47 46 Unfasten clips on bottom of seat. Unfasten clips from back of seat. To Remove Feeding Booster from Chair WARNING DO NOT remove feeding booster seat with the child in it. FALL HAZARD Never move or lift high chair or booster seat with child in it.

Page 28 - To Store Legs

To Store Legs To remove front legs, press button on side of seat and pull leg out a little.NOTE: DO NOT pull leg out completely until you have pressed button on the other side of seat to release the other leg. 51 52

Page 30 - Care and Maintenance; FROM TIME TO TIME CHECK YOUR HIGHCHAIR; TO CLEAN REMOVABLE SEAT COVER,

Care and Maintenance s FROM TIME TO TIME CHECK YOUR HIGHCHAIR for worn parts, torn vinyl or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. s TO CLEAN HIGHCHAIR FRAME , use only household soap and warm water. NO BLEACH or detergent. s TO CLEAN REMOVABLE SEAT COVER...