Page 2 - -A Car Seat Features; Important
2 1-A A Quick Guide to Your Manual1-B Welcome to the Graco Family1-C Right Mode of Use1-D Before You Begin Register This Car Seat If You Need Help Cer tification Car Seat’s Useful Life Vehicle Seat Protection Warm Weather Use 1-E Safety Warnings 2-A Car Seat Features 1 Important Pages 6-23 2 Feature...
Page 3 - -C Install Forward-Facing With Vehicle Seat Belt; Forward-Facing Use; -C Install Rear-Facing With Vehicle Seat Belt; Rear-Facing Use
3 1 Important Pages 6-23 4-A Forward-Facing4-B Installing Forward-Facing With LATCH Straps 4-C Install Forward-Facing With Vehicle Seat Belt 4 Forward-Facing Use Pages 48-61 3-A Rear-Facing3-B Installing Rear-Facing With LATCH Straps 3-C Install Rear-Facing With Vehicle Seat Belt 3 Rear-Facing Use P...
Page 6 - -A A Quick Guide to Your Manual; This car seat is for children:; Get to Know Your Car Seat; Adult Assembly Required; You MUST attach cup holders. Remove; seat cover. Line up tab on bottom of
6 1-A A Quick Guide to Your Manual This car seat is for children: Rear-Facing: 4-40 lb (1.8-18 kg) Forward Facing: 22-65 lb (10-30 kg) • Children less than 22 lb (10 kg) MUST use this car seat rear-facing. Review section 1-C for more information. Get to Know Your Car Seat Review section 2-A to see a...
Page 7 - According to accident statistics, the safest
7 What Seating Location Should I Use? Which Installation Method Should I Use? This car seat can be installed in your vehicle using either the vehicle seat belt OR the LATCH system. Both are equally safe to use. DO NOT USE BOTH AT THE SAME TIME. Vehicle Seat Belt: Review section 8 and your vehicle ow...
Page 8 - Review your vehicle’s owner manual for exact location and use.; Vehicle Top Tether; Typical seat in a passenger; Vehicle Seat Bight
8 LATCH consists of lower anchors and top tether anchors, which are built- in to your vehicle, and connecting hooks that are built-in to your car seat. Lower anchors are used INSTEAD of the vehicle’s seat belt to secure the child seat to the vehicle. Top tethers are used IN ADDITION to the lower anc...
Page 10 - Does Your Car Seat Fit Your Child Correctly?
10 Does Your Car Seat Fit Your Child Correctly? To make sure your child is secured properly, review section 3 and 4 to understand all of the actions you need to take to properly adjust the car seat to fit your child. Harness Height, Rear-Facing (A) Harness straps at or just below the child’s shoulde...
Page 12 - Car Seat Does Not Move More; Review section 3; Harness Straps at or Just; Cannot Pinch Harness Straps; Review section 5; Rear-Facing Installation
12 LABEL NUMBER: PD349436A DESCRIPTION:LABEL-CARSEAT-SEQUEL 65-LEVEL INDICATOR LABEL MUST PASS GRACO LABEL SPECIFICATIONS DIMENSIONS: 1.75" X 1.995" DIE CUT DOES NOT PRINT CORNERS: ROUNDED 0.2" COLOR: BACKGROUND: WHITE TEXT: BLACK OTHER: PMS2726C, PMS2915C, RED PMS 192C MATERIAL: 0.006...
Page 13 - Forward-Facing Installation
13 Use the top tether strap when using forward-facing (A) When used properly, the top tether helps reduce injury in a sudden stop or crash. Review section 4 Car Seat Does Not Move More than 1” (2.5 cm) at the Belt Path (B) Review section 4 Harness Straps at or Just Above Child’s Shoulders (C) Review...
Page 15 - -C Right Mode of Use
15 1-C Right Mode of Use Note: Preterm or low bir th weight infants may be at special risk in a vehicle or aircraft. According to the AAP, these infants may suffer breathing issues if improperly reclined in a car seat. When rear-facing, use the corrected age for preemies. Graco advises that you have...
Page 16 - or register online at; Register This Child Restraint
16 1-D Before You Begin Please fill out the prepaid registration postcard attached to the harness and mail it in today or register online at www.gracobaby.com/carseatregistration. Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send ...
Page 17 - on the date label located on the back of the car seat.
17 Please fill out the prepaid registration postcard attached to the harness and mail it in today or register online at www.gracobaby.com/carseatregistration. Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, a...
Page 18 - vehicle safety standard 213 for use in motor vehicles.; Certification
18 STOP using this car seat and throw it away 10 years after the date of manufacture. Look for this sticker on back of the car seat.Graco Children’s Products Inc. advises against loaning or passing along a car seat unless you know the complete history of the product. We also advise against purchasin...
Page 19 - Car seat par ts can get very hot in the sun or warm weather.; always check before putting child in car seat.; No car seat can guarantee protection from injury in; Warm Weather Use
19 STOP using this car seat and throw it away 10 years after the date of manufacture. Look for this sticker on back of the car seat.Graco Children’s Products Inc. advises against loaning or passing along a car seat unless you know the complete history of the product. We also advise against purchasin...
Page 20 - and cause serious injury or death to your child.; Review your vehicle owner’s manual for more information
20 ! NEVER PLACE THIS CHILD RESTRAINT REAR-FACING IN A VEHICLE SEATING LOCATION THAT HAS AN ACTIVE FRONT AIR BAG. If an air bag inflates, it can hit the child and car seat with great force and cause serious injury or death to your child. ! Review your vehicle owner’s manual for more information abou...
Page 24 - eatures; -A Car Seat Features
24 2 F eatures 2-A Car Seat Features A B E F C G H I D
Page 25 - I Base Recline Handle
25 2 Features A Height Adjust LeverB HeadrestC Harness CoverD CupholderE Harness Adjustment Strap F Chest ClipG Harness BuckleH Harness Release Lever (under seat pad) I Base Recline Handle
Page 30 - Rear Facing; MUST; LATCH Strap; even with or
30 3 Rear Facing 3-A Rear-Facing Rear-Facing: 4-40 lb (1.8-18 kg) • Infants who weigh less than 22 lb (10 kg) MUST be rear-facing. • Place car seat rear-facing in the vehicle back seat. • Make sure LATCH strap or vehicle seat belt is routed through the rear-facing belt path marked with a blue label....
Page 31 - Facing; Vehicle Seat Lap Belt; NEVER place this child; Vehicle Seat Lap/Shoulder Belt
31 3 Rear Facing Vehicle Seat Lap Belt NEVER place this child restraint rear-facing in a vehicle seating location that has an active front air bag. • Harness straps need to be even with or just below the top of child’s shoulders and chest clip is at armpit level . The AAP and NHTSA recommend that ch...
Page 32 - When reading the level indicator,; RED
32 3 Rear Facing When reading the level indicator, - If the ball is entirely in light blue, the restraint is level for infants 0+ months in age. - If the ball is in light blue and dark blue, the restraint is level for a child 3+ months in age. - If the ball is in RED , child restraint is NOT level. ...
Page 33 - -B Installing Rear-Facing With LATCH Straps; Review your vehicle’s owner manual for LATCH location and use.; Store Top Tether Strap; Attach tether hook to the plastic bar on; Remove LATCH Strap from Storage; Press in on the hook’s spring. Push hook
33 3 Rear Facing 3-B Installing Rear-Facing With LATCH Straps Review your vehicle’s owner manual for LATCH location and use. 1. Store Top Tether Strap Attach tether hook to the plastic bar on right side of the car seat. 2. Remove LATCH Strap from Storage Location Press in on the hook’s spring. Push ...
Page 34 - Make Sure LATCH Strap is in the; If not, See section 7 to move LATCH strap.; Recline the Car Seat; Pull out on handle on front of child
34 3 Rear Facing 3. Make Sure LATCH Strap is in the Rear-Facing Belt Path Marked With a Blue Label If not, See section 7 to move LATCH strap. 4. Recline the Car Seat Pull out on handle on front of child restraint and adjust to one of the 3 rear-facing positions. 6 5 Forward F acing 2 1 Rear Facing 4...
Page 35 - in Back Seat of the Vehicle; Place rear-facing in vehicle seat and
35 3. Make Sure LATCH Strap is in the Rear-Facing Belt Path Marked With a Blue Label If not, See section 7 to move LATCH strap. 3 Rear Facing 5. Place Car Seat Rear-Facing in Back Seat of the Vehicle Place rear-facing in vehicle seat and center the car seat between the lower LATCH anchors. The base ...
Page 36 - Make Sure Base is a minimum of; must be completely in the blue zone.
36 3 Rear Facing 6. Make Sure Base is a minimum of 80% on Vehicle Seat. 7. Check the Level Indicator Vehicle MUST be on level ground. Ball must be completely in the blue zone. Readjust the incline if needed. Or if needed, rolled towels may be placed under the car seat at the vehicle seat crease, unt...
Page 37 - Attach LATCH Connectors to
37 3 Rear Facing continue next page 8. Extend the LATCH Strap. For easier installation, extend the LATCH strap to its maximum length by pressing the grey button and pulling on the strap. CLICK! 9. Attach LATCH Connectors to Vehicle’s Lower LATCH Anchors. LATCH strap should lie flat and not be twiste...
Page 38 - Test For Tightness
38 3 Rear Facing 11. Test For Tightness Grab the sides of the seat where the LATCH strap is and slide the car seat side-to-side and front-to-back.If the seat moves less than 1”. (2.5 cm), it is tight enough. 10. Tighten the LATCH Strap Press down firmly in the center of the car seat while tightening...
Page 39 - Check the Level Indicator; Vehicle MUST be on level ground. Ball; under the car seat at the vehicle seat
39 3 Rear Facing continue next page 12. Check the Level Indicator Vehicle MUST be on level ground. Ball must be completely in the blue zone. Readjust if needed.For infants 3 months and under, the ball must completely cover the light blue circle. If needed, rolled towels may be placed under the car s...
Page 40 - Is Everything Correct?
40 3 Rear Facing Is Everything Correct? Car Seat Does Not Move More than 1” (2.5 cm) at the Belt Path Level Indicator’s Ball in the Blue Zone and Vehicle on Level Ground Harness Straps at or Just Below the Child’s Shoulders. Review section 5 Chest Clip Even With Armpits Review section 5 Cannot Pinch...
Page 41 - Vehicle Seat Belt
41 3 Rear Facing 1. Store Top Tether and LATCH Strap Attach tether hook and LATCH connectors to the plastic bars as shown. 6 5 Forward F acing 2 1 Rear Facing 4 3 PD349426A 3-C Install Rear-Facing with Vehicle Seat Belt 2. Recline the Car Seat Pull out on handle on front of child restraint and adjus...
Page 42 - Back Seat of the Vehicle; base should sit as flat as possible on the; Make Sure Base is a minimum of
42 3 Rear Facing 3. Place Car Seat Rear-Facing in Back Seat of the Vehicle Place rear-facing in vehicle seat. The base should sit as flat as possible on the vehicle seat. 4. Make Sure Base is a minimum of 80% on Vehicle Seat.
Page 44 - Lock Vehicle Seat Belt; Review your vehicle’s owner manual for vehicle seat belt use; Route the Vehicle Seat Belt
44 3 Rear Facing 7. Lock Vehicle Seat Belt In most vehicles today, slowly pull the shoulder belt all the way out and then let it go back in. You will hear a clicking sound. Slowly pull out on the belt and it should be locked. If not, review your car’s owner manual and section 8-D. 8. Tighten the Veh...
Page 45 - In most vehicles today, slowly pull the; Tighten the Vehicle Seat Belt
45 3 Rear Facing 7. Lock Vehicle Seat Belt In most vehicles today, slowly pull the shoulder belt all the way out and then let it go back in. You will hear a clicking sound. Slowly pull out on the belt and it should be locked. If not, review your car’s owner manual and section 8-D. 8. Tighten the Veh...
Page 46 - Test For Tightness; Check the Level Indicator; Vehicle MUST be on level ground. Ball must
46 3 Rear Facing 9. Test For Tightness Grab the sides of the seat where the vehicle seat belt is and slide the car seat side-to- side and front-to-back.If the seat moves less than 1” (2.5 cm), it is tight enough. 10. Check the Level Indicator Vehicle MUST be on level ground. Ball must be completely ...
Page 48 - and at least one year old; • The crotch strap must be in the front-; • Place car seat forward-facing in the
48 4 For ward Facing 4-A Forward-Facing Forward-Facing: 22-65 lb (10-30 kg) and 49 inches (125 cm) or less and at least one year old • The crotch strap must be in the front- most slot when forward facing. • Place car seat forward-facing in the vehicle back seat. • Make sure LATCH strap or vehicle se...
Page 49 - should not move
49 Important 4 For ward Facing • Install this car seat tightly in your vehicle. Car seat should not move at the forward-facing belt path more than 1”. (2.5 cm) from side to side, front to back. • Harness straps need to be even with or just above the top of child’s shoulders and chest clip is at armp...
Page 50 - with LATCH Straps; Do not
50 4 For ward Facing 1. Remove LATCH Strap from Storage Location 4. Recline the Car Seat Pull out on handle on front of child restraint and adjust to one of the 3 forward-facing positions. 4-B Install Forward-Facing with LATCH Straps Review your vehicle’s owner manual for LATCH location and use. Do ...
Page 52 - Attach LATCH Connectors to
52 4 For ward Facing 6. Make Sure Base is a minimum 80% on Vehicle Seat. 7. Extend the LATCH Strap. For easier installation, extend the LATCH strap to its maximum length by pressing the grey button and pulling on the strap. 8. Attach LATCH Connectors to Vehicle’s Lower LATCH Anchors. LATCH strap sho...
Page 53 - Press down firmly in the center of the car; Attach Top Tether Strap; Extend the top tether
53 Important 4 For ward Facing 9. Tighten the LATCH Strap Press down firmly in the center of the car seat while tightening the LATCH strap. 10. Attach Top Tether Strap Extend the top tether by pressing the grey button and pulling on the strap and attach. Consult vehicle’s owner manual for specific l...
Page 54 - Test For Tightness; Grab the sides of the seat where the; Tighten Top Tether Strap; Remove all the slack.
54 4 For ward Facing 12. Test For Tightness Grab the sides of the seat where the LATCH strap is and slide the car seat side-to-side and front-to-back.If the seat moves less than 1” (2.5 cm), it is tight enough.See section 5-A to secure your child. 11. Tighten Top Tether Strap Remove all the slack.
Page 56 - Make Sure Base is a minimum of
56 4 For ward Facing 4-C Install Forward-Facing with Vehicle Seat Belt 1. Store LATCH Strap Attach LATCH connectors to the plastic bars as shown. 4. Place Car Seat Forward-Facing in Back Seat of the Vehicle Place forward-facing in vehicle seat. The base should sit as flat as possible on the vehicle ...
Page 57 - Place forward-facing in vehicle seat. The; Unhook tether and lay it in the seat.; Recline the Car Seat
57 Important 4 For ward Facing 4-C Install Forward-Facing with Vehicle Seat Belt 4. Place Car Seat Forward-Facing in Back Seat of the Vehicle Place forward-facing in vehicle seat. The base should sit as flat as possible on the vehicle seat. 5. Make Sure Base is a minimum of 80% on Vehicle Seat. 3. U...
Page 61 - Car Seat Does Not Move More than; Chest Clip Even With Armpits; Cannot Pinch Harness Straps at the
61 Important 4 For ward Facing Is Everything Correct? Car Seat Does Not Move More than 1” (2.5 cm) at the Belt Path Harness Straps at or Just Above the Child’s Shoulders. Review section 5 Chest Clip Even With Armpits Review section 5 Cannot Pinch Harness Straps at the Shoulder Review section 5
Page 62 - Loosen Harness Straps; Lift up on the harness release lever; WARNING! Do not put snowsuits or bulky garments on your child
62 5 Securing Child 1. Loosen Harness Straps Lift up on the harness release lever while pulling out on the harness straps at the chest clip. Unbuckle the chest clip and the crotch buckle. Place harness straps off to the sides. 5-A Securing Child 5-point Harness WARNING! Do not put snowsuits or bulky...
Page 63 - Securing
63 1. Loosen Harness Straps Lift up on the harness release lever while pulling out on the harness straps at the chest clip. Unbuckle the chest clip and the crotch buckle. Place harness straps off to the sides. 5 Securing Child Unbuckle the chest clip and the crotch buckle.
Page 64 - Place Your Child in the Seat
64 5 Securing Child 2. Place Your Child in the Seat Make sure their back is flat against the car seat back. Avoid bulky or heavy clothing. Doing so will prevent the harness straps from being tightened properly. Place a blanket over the child after you have secured the child. 3. Place Harness Straps ...
Page 65 - at or just above
65 5 Securing Child 2. Place Your Child in the Seat Make sure their back is flat against the car seat back. Avoid bulky or heavy clothing. Doing so will prevent the harness straps from being tightened properly. Place a blanket over the child after you have secured the child. 3. Place Harness Straps ...
Page 66 - Harness Height; Squeeze the adjustment handle and move; Check the Buckle Position; The correct slot is the one that is closest
66 5 Securing Child 5. To Raise or Lower Headrest/ Harness Height Squeeze the adjustment handle and move headrest for the proper harness height. 6. Check the Buckle Position The correct slot is the one that is closest to your child without being underneath them.The crotch strap MUST be in the front-...
Page 68 - Buckle the Chest Clip; You will hear a “click” when the chest; Pull All the Slack Out From; Pull up on the harness strap while
68 5 Securing Child 10. Pull Up on Crotch Strap to Make Sure it is Secured 11. Buckle the Chest Clip You will hear a “click” when the chest clip is securely buckled. 12. Pull All the Slack Out From Around the Waist Pull up on the harness strap while pushing the chest clip down. Do this to both sides...
Page 70 - Accessorie; Harness Covers; Make sure that harness covers do not
70 6 Accessorie s 6-A Accessories (on select models) Harness Covers Make sure that harness covers do not interfere with placement of the chest clip at armpit level. To remove, undo the fastening strips and remove.
Page 71 - Body Support; Body suppor t must be used if shoulders
71 Impo rt ant Im po rt an t 6 Accessorie s Body Support Use only in the rear-facing mode. Body suppor t must be used if shoulders are below the lowest harness setting.Never allow body suppor t to bunch or fold behind child.
Page 72 - -A Moving the LATCH Strap; Feed the LATCH Connector with the Adjuster Closest to it; A. Undo Snaps and fastening strips in front
72 7 Moving LA TC H 7-A Moving the LATCH Strap B A 3. Feed the LATCH Connector with the Adjuster Closest to it Through the Chosen Belt Path 1. For Ease of Moving the LATCH Strap A. Undo Snaps and fastening strips in front of child restraint. B. Pull the LATCH straps out of the belt path opening, so ...
Page 73 - Slide Entire LATCH Strap Along Bar; Slide LATCH strap down; Make sure the LATCH strap is in front of the buckle strap when
73 7 Moving LA TC H 2. Slide Entire LATCH Strap Along Bar to Correct Belt Path Opening Rear-Facing: Slide LATCH strap down to the blue label. Forward-Facing: slide the LATCH strap up to the orange label. 3. Feed the LATCH Connector with the Adjuster Closest to it Through the Chosen Belt Path Rear-Fa...
Page 74 - Replace the Seat Pad Fabric on the; Make sure the
74 7 Moving LA TC H 4. Replace the Seat Pad Fabric on the Front of the Child Restraint. Forward-Facing: Make sure the strap is flat and not twisted.
Page 75 - Top Tether Strap; To remove, press the grey button; -A How to Remove LATCH and Top Tether; LATCH
75 8 Additional Informatio n Top Tether Strap To remove, press the grey button and pull on the strap to release the tension. Press in on the hook’s spring. Push tether hook in, then lift up and pull away from tether anchor. 8-A How to Remove LATCH and Top Tether LATCH Push gray button in while pulli...
Page 76 - Additional Informatio; -B Choosing Vehicle Seat Location; Review your vehicle owner’s manual for seating locations.
76 8 Additional Informatio n 8-B Choosing Vehicle Seat Location Review your vehicle owner’s manual for seating locations. The best seating location for this car seat is one that: • Is recommended by your vehicle owner’s manual, and • Results in a secure installation of this car seat In the event the...
Page 77 - deployment path of the air bag; -C Unsafe Vehicle Seat Locations; vehicle seats
77 8 Additional Informatio n 8-B Choosing Vehicle Seat Location In the event there is no available back seat and / or you have no other option than to place a child in a front passenger seating position (other than rear-facing), the National Highway Traffic Safety Administration (NHTSA) recommends t...
Page 78 - -D Vehicle Seat Belts; Review your vehicle owner’s manual for vehicle seat belt use; Retractor; A device that winds up the unused vehicle seat belt.; Latch Plate; The male end of the seat belt with the silver tongue.; Seat Bight; The crease where the vehicle seat back and seat
78 8 Additional Informatio n 8-D Vehicle Seat Belts This car seat can be installed using a vehicle seat belt. To do this, you will need to change the seat belt to a locked mode for use with car seats. With some vehicle seat belts, this is done with the latchplate; with other vehicle seat belts, this...
Page 79 - Identify Your Seat Belt Type; Lap Belt Only
79 8 Additional Informatio n 8-D Vehicle Seat Belts Identify Your Seat Belt Type There are two different types of vehicle seat belts that can be used with this car seat: Lap Belt Only 2 connection points. Lap/Shoulder Belt 3 connections points. Can be used in all car seats modes of use. The followin...
Page 80 - Sliding Latch Plate and Switchable
80 8 Additional Informatio n Always review your vehicle owner’s manual for specific information about your vehicle seat belts. There are three types of retractors: ELR (Emergency Locking Retractor), ALR (Automatic Locking Retractor) , and Switchable (ELR switch to ALR). To determine your type of ret...
Page 81 - How to Lock Your Lap and Shoulder Vehicle Seat Belt; A latchplate that slides freely on the belt webbing; Slowly pull the shoulder belt all the way out; the vehicle seat belt tight, feed all the slack back
81 8 Additional Informatio n How to Lock Your Lap and Shoulder Vehicle Seat Belt Sliding Latch Plate and Switchable Retractor A latchplate that slides freely on the belt webbing and cannot, by itself, hold the belt snug around a car seat. When installing the car seat, route the vehicle seat belt thr...
Page 83 - Slowly pull the shoulder belt all the way
83 8 Additional Informatio n Locking Latchplate and ELR Retractor A latchplate that holds the lap belt snug after it has been adjusted; contains a metal bar on the underside of the hardware that “locks” the belt in position. When installing the car seat, route the vehicle seat belt through the prope...
Page 84 - Sliding Latch Plate and ELR Retractor; Locking Clip
84 8 Additional Informatio n Sliding Latch Plate and ELR Retractor A latchplate that slides freely on the belt webbing and cannot, by itself, hold the belt snug around a car seat. With this retractor, you will need to use the locking clip to lock the vehicle seat belt.To get a locking clip order onl...
Page 85 - Lap Belt Installation; Sewn On Latch Plate and ALR; Slowly pull the lap belt all the way out.
85 8 Additional Informatio n Lap Belt Installation Always review your vehicle owner’s manual for specific information about your vehicle seat belts. Locking Latch Plate and No Retractor When installing the car seat, route the lap seat belt through the proper path and buckle it in. Then, pull upwards...
Page 86 - -A Cleaning Seat Pad; Clean with a damp sponge using mild soap; Seat Pad
86 9 Care & Cleaning 9-A Cleaning Seat Pad Clean with a damp sponge using mild soap and cool water. Refer to seat pad care tag for washing instructions.Your model determines how to remove the seat pad. Follow the instructions that match your seat. Raise the headrest all the way up.Lift up on the...
Page 88 - Grab hold of the shoulder straps and pull
88 9 Care & Cleaning Grab hold of the shoulder straps and pull them out of their slots on the seat pad. From the back of the seat, undo the elastic straps and plastic hooks. Undo both plastic hooks from the front of the seat.
Page 89 - THE METAL BAR. The harness straps
89 Impo rt ant Im po rt an t 9 Care & Cleaning Remove pad from shell. Machine wash pad in cold water on delicate cycle and drip-dry. DO NOT USE BLEACH. To put the seat pad back on, reverse preceding steps. Make sure that you rethread the harness straps OVER THE METAL BAR. The harness straps MUST...
Page 90 - Head Support Cover; Undo elastic loop underneath head
90 9 Care & Cleaning Head Support Cover Undo elastic loop underneath head suppor t cover. Pull tab out from behind head suppor t. Undo the elastic loops on the sides of the headrest.Peel cover off head suppor t. Machine wash pad in cold water on delicate cycle and drip-dry. DO NOT USE BLEACH.To ...
Page 91 - -B Cleaning Crotch Buckle; Inspect and clean
91 Impo rt ant Im po rt an t 9 Care & Cleaning 9-B Cleaning Crotch Buckle WARNING! Inspect and clean buckle from time to time to remove any objects or debris that could prevent latching. Recline the car seat and locate the metal retainer. Rotate the metal retainer up through the shell and pad. F...
Page 92 - -C Cleaning Harness and LATCH; Surface wash only with mild soap and damp cloth.; DO NOT IMMERSE; Doing so may
92 9 Care & Cleaning 9-C Cleaning Harness and LATCH Straps Surface wash only with mild soap and damp cloth. DO NOT IMMERSE THE HARNESS STRAPS or LATCH STRAP IN WATER Doing so may weaken the straps. If harness straps or LATCH belt are frayed or heavily soiled, contact Customer Service at www.grac...
Page 96 - or; Replacement Parts
96 To purchase par ts or accessories in the United States, please contact us at the following: www.gracobaby.com or 1-800-345-4109 Replacement Parts Store instruction manual behind the tab with the instruction book icon as shown.