Graco Formula-X - Manual - manualsarea.com

Page 2 - Contents

2 GC-1393F Contents Warnings .......................................................... 3 Important Safety Information ......................... 5 Grounding ........................................................ 6 Set-Up ............................................................... 7 Parts ........

Page 3 - Warnings; Splatter Hazard; WARNING; WARNING

3 GC-1393F Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure- specific risk. Refer back to these warnings. Additional, product-specific w...

Page 4 - Pressurized Aluminum Parts Hazard; Plastic Parts Cleaning Solvent Hazard; Skin Injection Hazard; - Use with UL1450 Compliance

4 GC-1393F WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the bo...

Page 5 - Important Safety Information; Polyester Resins and Gel-Coats; Isocyanate Conditions

5 GC-1393F Important Safety Information Methyl Ethyl Ketone Peroxide (MEKP) MEKP is among the more hazardous materials found in commercial channels. Proper handling of the “unstable (reactive)” chemicals presents a definite challenge to the plastics industry. The highly reactive property which makes...

Page 7 - Hose Attachment

7 GC-1393F Hose Attachment 1. Push in and rotate the trigger lock to stop the trigger from being activated. 2. Attach the (black p/n 21694-25) material hose to the material inlet fitting on the back of the gun. 3. Attach the (red) atomize air tubing to the atomize air inlet fitting on the back of th...

Page 8 - Parts

8 GC-1393F Repair Kits Part Number Description 23792-00 GUN AIR KIT 23793-00 GUN SEAL KIT 23732-00 GUN FLUID VALVE KIT Standard Equipment Part Number Description 23750-01 FORMULA X DISPENSE GUN GC-1393 USER MANUAL Formula X Dispense Gun 23750-01 Parts

Page 9 - Assembly Drawings

9 GC-1393F 23750-01 Formula X Dispense Gun Assembly Drawings

Page 12 - Daily Maintenance; Pressure Relief Procedure

12 GC-1393F To relieve fluid and air pressures: 1. Push down Yellow slide valve, P/N 21402-00 to bleed off air to system. 2. Open P/N 21228-00 on catalyst pump to recirculation position. 3. Open P/N 21192-00 on bottom of material pump. 4. Verify the trigger lock is engaged. Daily Maintenance It is r...

Page 13 - Maintenance; Notice

13 GC-1393F Parts Replacement Procedure Formula Gun Before performing maintenance on the dispense gun, follow Pressure Relief Procedure. Due to the different o-ring materials and lubricants used in the dispense guns, never submerge or soak any dis - pense gun in any type of solvent. Submerging or so...

Page 15 - Dispense Tip Reference Chart; Part; Options

15 GC-1393F Dispense Tip Reference Chart Part Number Orifice 23047-J1 .012 J2 .014 J3 .022 M1 .012 M2 .014 M3 .022 N1 .012 N2 .014 N3 .022 P1 .012 P2 .014 P3 .022 Note: Use p/n: LPA2-120G and p/n: LPA2-121G when using LPA2-147-XXXX and 23047-XX series spray tips. Options

Page 17 - Technical Data; Category

17 GC-1393F Technical Data Category Data Maximum Fluid Working Pressure 2000 psi (14 MPa, 138 bar) Maximum Air Inlet Pressure 100 psi (0.7 MPa, 7 bar) Typical Flow Rate of Pattern Guns Dependent of spray tip Maximum Fluid temperature 100° F (38° C) Trigger Air 1/4in. Tube AAC Air 1/4in. Tube Atomize...

Page 18 - Graco Ohio Standard Warranty; Graco Ohio Information

Graco Ohio Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited...

Graco Formula-X - Manual

Table of Contents:

Summary

Other Graco Models