Graco 800-670 - Manual
Graco 800-670 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – WARNING; HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.; General Safety
- Page 3 – EQUIPMENT MISUSE HAZARD; DO NOT exceed the maximum working; Chemical Compatibility; HOSE SAFETY; DO NOT expose Graco hose to; FUEL AND EMISSION HAZARDS; ALWAYS fill
- Page 4 – MOVING PARTS HAZARD; KEEP CLEAR of moving parts when starting; TERMS; Identifies helpful procedures and information.; IMPORTANT
- Page 5 – INSTALLATION; Check for Shipping Damage; The water source at the unit
- Page 6 – STARTUP; NOTE: All units are equipped with a low–oil sensor; Turn on the water supply.; CAUTION
- Page 7 – ALWAYS engage the trigger safety; Figure 2; Installing and Changing Spray Tips; ALWAYS follow the; Follow the Pressure Relief Procedure.; Tip holding holes are provided on the chassis.; Figure 3
- Page 8 – Pressure Relief Procedure; Engage the trigger safety latch.; MAINTENANCE; Interval; Daily; What to do
- Page 9 – TROUBLESHOOTING CHART; PROBLEM; CAUSE
- Page 10 – PARTS DRAWING
- Page 11 – PARTS LIST; Systems
- Page 14 – The oil seal MUST be replaced if removed.; Assembling the Gear Reducer; on the
- Page 16 – NOTE: The oil seal MUST be replaced if removed.; Follow steps 1 and 3 under Replacing the Gasket.; Apply low strength Loctite
- Page 22 – PUMP SERVICE; Retorque the plug after 5 hours of operation.; Pumping Section; Carefully separate the manifold from the crankcase.; Figure 4
- Page 23 – Servicing the V–Packings; NOTE: There are two types of packing kits: one is just; Inspect all parts and replace as necessary.; ACCESSORIES
INSTRUCTIONS-PARTS LIST
308–523
Rev A
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
HYDRA-CLEAN 1535, 2040
Pressure Washer
HYDRA-CLEAN 1535, 5 HP ENGINE
P/N 800–670, Series A
P/N 800–671, Series A
1500 psi (103 bar) OPERATING PRESSURE
1900 psi (131 bar) MAXIMUM WORKING PRESSURE
HYDRA-CLEAN 2040, 8 HP ENGINE
P/N 800–672, Series A
P/N 800–674, Series A
2000 psi (138 bar) OPERATING PRESSURE
2400 psi (165 bar) MAXIMUM WORKING PRESSURE
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1990, GRACO INC.
1535
2040
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
WARNING HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety This pressure washer generates very high fluidpressure. Spray from the gun, leaks or ru...
EQUIPMENT MISUSE HAZARD General Safety Any misuse of the pressure washer or accessories,such as overpressurizing, modifying parts, usingincompatible chemicals and fluids, or using worn ordamaged parts, can cause them to rupture and result influid injection, splashing in the eyes or on the skin, orot...
4 308-523 MOVING PARTS HAZARD Moving parts can pinch or amputate fingers or otherbody parts. KEEP CLEAR of moving parts when starting or operating the pressure washer. NEVER operate the pressure washer without all guardsand interlocks installed and functioning. Follow the Pressure Relief Procedure b...
