Graco 5 - Manual
Graco 5 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – WARNING
- Page 3 – Pressure Relief Procedure; RAC Tip
- Page 4 – Operation; Adjusting Spray Pattern; Maintenance; Flushing
- Page 5 – Repair; Disassembly; Assembly; Technical Data; Caution
- Page 6 – Parts; Tip and Guard; NOTE: Handles 15a and 15b are not pressure rated
- Page 7 – Related Manuals; Table 2: XTR 5 Models; Language
- Page 8 – Graco Standard Warranty
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point sym-
bol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. Refer back to these warnings. Addi-
tional product-specific warnings may be found throughout the body of this manual where applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but
it is a serious injury that can result in amputation. Get immediate surgical treatment.
•
Do not point gun at anyone or at any part of the body.
•
Do not put your hand over the spray tip.
•
Do not stop or deflect leaks with your hand, body, glove, or rag.
•
Do not spray without tip guard and trigger guard installed.
•
Engage trigger lock when not spraying.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or
servicing equipment.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause seri-
ous injury.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or
servicing equipment.
•
Tighten all fluid connections before operating the equipment.
•
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and
explosion:
•
Use equipment only in well ventilated area.
•
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths
(potential static arc).
•
Keep work area free of debris, including solvent, rags and gasoline.
•
Do not plug or unplug power cords or turn power or light switches on or off when flammable fumes are present.
•
Ground all equipment in the work area. See Grounding instructions.
•
Use only grounded hoses.
•
Hold gun firmly to side of grounded pail when triggering into pail.
•
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you
identify and correct the problem.
•
Keep a working fire extinguisher in the work area.
XTR
™
5 and XTR
™
7 Airless Spray Gun
Instructions/Parts
See page 7 for model numbers.
Maximum Working Pressure:
XTR 5: 5000 psi (35 MPa, 345 bar)
XTR 7: 7250 psi (50 MPa, 500 bar)
For use with protective coating materials
IMPORTANT SAFETY INSTRUCTIONS.
Refer to
your sprayer instruction manual for pressure relief, priming,
and spraying instructions. Keep these instructions.
Instructions
English
ti5045a
II 2 G c T6
312145B
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
WARNING 2 312145B EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all eq...
Pressure Relief Procedure 312145B 3 Pressure Relief Procedure Follow this Pressure Relief Procedure whenever you are instructed to relieve pressure, stop spraying, check or service equipment, or install or clean spray tip. 1. Engage trigger lock. 2. Shut off pump. 3. Disengage trigger lock. 4. Hold ...
Operation 4 312145B Operation 1. Connect a grounded fluid hose. 2. Without spray tip, flush pump. Use lowest pressure possible. 3. Prime. Refer to sprayer manual. 4. Follow Pressure Relief Procedure. 5. Install spray tip and tip guard. 6. RAC tips only: Be sure the arrow-shaped tip faces forward. 7....
