Graco 3A1657F- User Manual

Page 2 - Contents

Contents 2 3A1657F Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overview . . . . . . . . . . . . . . ....

Page 3 - Related Manuals

Related Manuals 3A1657F 3 Related Manuals Component manuals in English. Manuals are available at www.graco.com. Overview On HFR systems, the flow meters are used only as a method of monitoring system performance, which will help with system maintenance. The ratio displayed on the ADM is a running av...

Page 4 - Installation

Installation 4 3A1657F Installation Flow Meter Electronics Kit 24J318 1. Perform Shutdown procedure. See HFR or NVH operation manual for detailed instructions. 2. Use two 111800 hex head screws (supplied) to mount electronics assembly 24J318 to the bottom of the electrical enclosure. If there are tr...

Page 5 - HFR: 3000 Series Flow Meter

Installation 3A1657F 5 HFR: 3000 Series Flow Meter 1. Perform HFR Pressure Relief Procedure . See HFR operation manual for detailed instructions. 2. Perform dispense valve Pressure Relief Proce- dure . See dispense valve manual, page 3, for detailed instructions. 3. Verify all air, hydraulic, and ma...

Page 6 - HFR: 6000 Series Flow Meter

Installation 6 3A1657F HFR: 6000 Series Flow Meter 1. Perform HFR Pressure Relief Procedure . See HFR operation manual for detailed instructions. 2. Perform dispense valve Pressure Relief Proce- dure . See dispense valve manual, page 3, for detailed instructions. 3. Verify all air, hydraulic, and ma...

Page 8 - NVH Flow Meters

Installation 8 3A1657F NVH Flow Meters 1. Perform HFR for NVH Pressure Relief Procedure . See HFR for NVH operation manual for detailed instructions. 2. Perform dispense valve Pressure Relief Proce- dure . See dispense valve manual, page 3, for detailed instructions. 3. Verify all air, hydraulic, an...

Page 10 - HFR: Calibration Kit

Installation 10 3A1657F HFR: Calibration Kit In order to perform the calibration procedure the HFR system must have circulation lines going from the sys-tem fluid manifold back to the tanks. If the system does not have circulation lines, a calibration kit must be pur-chased and installed. See HFR: F...

Page 12 - Calibration; Using a Blocked Orifice

Calibration 12 3A1657F Calibration The following procedure describes how to adjust the mass flow rate calculated by the machine. To calculate the mass flow rate, the machine uses the chemical spe-cific gravities entered in the Setup screens, the volumet-ric flow measured by the flow meters, and the ...

Page 13 - Parts and Tools Required

Calibration 3A1657F 13 Parts and Tools Required GX-7DI Only • 5/16 Nut Driver • Adjustable Wrench • Scale • Two large containers with lids (a hole will need to be cut into the lid slightly larger than the spray nozzle. Using a 5 gallon pail and removing the pull out spout from the bung is recommende...

Page 14 - Calibrate Material Weight Measurement

Calibration 14 3A1657F Calibrate Material Weight Measurement For more detailed instructions regarding steps in this procedure, see Related Manuals listed on page 3. 1. If not already completed, install the flow meters. See Installation starting on page 12. 2. If the HFR system does not have circulat...

Page 19 - Flow Meter Connector Pinout; Maintenance; Install Upgrade Token

Flow Meter Connector Pinout 3A1657F 19 Flow Meter Connector Pinout The system utilizes a 5-pin CAN connection for commu-nication with the flow meter. If a non-Graco flow meter is used the flow meter signal must be converted to the fol-lowing 5-pin connection. NOTE: The connection shown is the FCM co...

Page 20 - Parts; HFR and NVH: Flow Meter Electronics Kit, 24J318

Parts 20 3A1657F Parts HFR and NVH: Flow Meter Electronics Kit, 24J318 ti17023a 101 112 105 106 104 109 110 111 102 107 103 108 Ref Part Description Qty 101 24J328 PLATE, mounting, electronics 1 102 289697 MODULE, base 1 103 289696 MODULE, FCM 1 104 24H240 HARNESS, wire, ground, term, 9 in. 1 105 10...

Page 21 - HFR: 3000 Series Flow Meter Kits

Parts 3A1657F 21 HFR: 3000 Series Flow Meter Kits ti17024a 203 202 206 204 205 201 Ref Part Description Quantity 24J319, S3000 24J320, G3000 24J321, G3000HR 201 258718 METER, gear, S3000 1 239716 METER, gear, G3000 1 244292 METER, gear, G3000HR 1 202 262205 FITTING, swivel, npt x JIC 1 1 1 203 26220...

Page 22 - HFR: 6000 Series Flow Meter Kits

Parts 22 3A1657F HFR: 6000 Series Flow Meter Kits ti17016a 302 303 304 301 305 Ref Part Description Quantity 24J322, HG6000 24J323, HG6000HR 301 246190 METER, helical gear, HG6000 1 246652 METER, helical gear, HG6000HR 1 302 114190 SWIVEL, stainless steel, 1/2 npt 1 1 303 114496 FITTING, nipple 1 1 ...

Page 25 - HFR: Flow Meter Calibration Kits for Hydraulic Dispense Valves

Parts 3A1657F 25 HFR: Flow Meter Calibration Kits for Hydraulic Dispense Valves * Parts 407, 408, 409 not shown. ti17025a 406 404 402 401 403 405 Ref Part Description Quantity 24J324, L-Head Kit 24J325, S-Head Kit 24J357, GX-16 Kit 401 262184 HOSE, b, 10 ft., 3/8 in., moisture-lok, mild steel 2 2 2 ...

Page 27 - Technical Data

Technical Data 3A1657F 27 Technical Data See Technical Data in the HFR or HFR for NVH system manuals for more information. Wetted Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 stainless steel, tungsten carbide, PTFE

Page 28 - Graco Standard Warranty; Graco Information

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual contains Eng...

Table of Contents:

Summary

Other Graco Models