Graco 3A0156B- User Manual

Page 3 - Warnings; WARNING

Warnings 3A0156B 3 Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-spe...

Page 6 - Component Identification

Component Identification 6 3A0156B Component Identification ti14839b 11. 12. 10. 13. 1. 2. 4. 5. 6. 7. 8. 9. 3. 1 Premium Digital Display 2 ON/OFF Switch 3 WatchDog ™ Switch (not available on Mark V or Standard Units) 4 Pressure Control 5 Prime / Spray Valve 6 Filter 7 Siphon Tube 8 Pump 9 Bearing H...

Page 7 - Grounding; Power Requirements

Grounding 3A0156B 7 Grounding The sprayer must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit. The sprayer cord includes a grounding wire with an appropriate groundi...

Page 9 - Setup

Setup 3A0156B 9 Setup 1. Standard Units Only: Connect Graco airless hose to sprayer. Tighten securely. 2. Standard Units Only: Connect other end of hose to gun and tighten securely. 3. Engage gun trigger safety. 4. Remove tip guard. 5. Check inlet strainer for clogs and debris. 6. Fill throat packin...

Page 11 - Switch Tip Installation; Spray

Switch Tip Installation 3A0156B 11 Switch Tip Installation 1. Use spray tip (A) to insert OneSeal ™ (B) into guard (C). 2. Insert Switch Tip. 3. Screw assembly onto gun. Tighten. Spray 1. Spray test pattern. Increase pressure to eliminate heavy edges. Use smaller tip size if pressure adjust-ment can...

Page 12 - WatchDog; Fast Flush

WatchDog ™ Protection System (Not Available on All Units) 12 3A0156B WatchDog ™ Protection System (Not Available on All Units) Pump stops automatically when material pail is empty. To Activate: 1. Perform Startup . 2. Premium units with digital display: Turn WatchDog switch ON and WD ON displays. EM...

Page 13 - Hose Reel

Hose Reel (Not Available on All Units) 3A0156B 13 Hose Reel (Not Available on All Units) 1. Make sure hose is routed through hose guide. 2. Lift and turn pivot lock 90° to unlock hose reel. Pull on hose to remove it from hose reel. 3. Pull reel handle up and turn clockwise to reel in hose. NOTE: The...

Page 14 - Digital Tracking System; Operation Main Menu; Job Gallons; Lifetime Gallons

Digital Tracking System (Not Available on All Units) 14 3A0156B Digital Tracking System (Not Available on All Units) Operation Main Menu Short press to move to next display. Press and hold (5 seconds) to change units or reset data. 1. Turn pressure to lowest setting. Trigger gun to relieve pressure....

Page 18 - Technical Data; Dimensions

Technical Data 18 3A0156B Technical Data Basic Sprayer Wetted Parts.............................. zinc- and nickel-plated carbon steel, nylon, stainlesssteel, PTFE, Acetel, leather, UHMWPE, aluminumtungsten carbide, PEEK, brass Noise Level Sound power ...............................................9...

Page 19 - Notes

Page 20 - Graco Standard Warranty; Graco Information

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 3A0156 Graco Headquarters: Minneapolis Int...

Table of Contents:

Other Manuals for Graco 3A0156B

Summary

Other Graco Models