Graco 288425 - Manual
Graco 288425 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Connect Gun to Sprayer; Operation; Spraying; WARNING; EQUIPMENT MISUSE HAZARD; PERSONAL PROTECTIVE EQUIPMENT
- Page 3 – Parts; Tip and Guard; RAC X
- Page 4 – Maintenance; Replacing Needle; Translated Manuals; Technical Data
For the application of architectural paints and coatings.
Maximum Working Pressure: 3600 psi (248 bar, 24.8 MPa)
IMPORTANT SAFETY INSTRUCTIONS.
Read all
warnings and instructions in this manual. Refer to your
sprayer instruction manual for Pressure Relief, priming and
spray instructions. Save all instructions.
ti8501b
ti8522b
Instructions-Parts
Contractor & FTx Spray Guns
Contractor Models: 288420, 288421, 288425, 288475, 288477, 288478, 826085, 288009
FTx Models: 288427, 288428, 288429, 288430, 288431, 288436, 288438, 288477,
288478, 826086, 288008,262114, 262116
311861G
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol
alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional,
product-specific warnings may be found throughout the body of this manual where applicable.
WARNING
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it
is a serious injury that can result in amputation. Get immediate surgical treatment.
•
Do not point gun at anyone or at any part of the body.
•
Do not put your hand over the spray tip.
•
Do not stop or deflect leaks with your hand, body, glove, or rag.
•
Do not spray without tip guard and trigger guard installed.
•
Engage trigger lock when not spraying.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or
servicing equipment.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and
explosion:
•
Use equipment only in well ventilated area.
•
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths
(potential static arc).
•
Keep work area free of debris, including solvent, rags and gasoline.
•
Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.
•
Ground all equipment in the work area. See Grounding instructions.
•
Use only grounded hoses.
•
Hold gun firmly to side of grounded pail when triggering into pail.
•
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you iden-
tify and correct the problem.
•
Keep a working fire extinguisher in the work area.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause a serious chemical reation and
equipment rupture. Failure to follow this warning may result in death, serious injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids contain-
ing such solvents.
• Many other fluids may contain materials that are incompatible with aluminum. Contact your material supplier for
verification.
II 2 G
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 311861G Pressure Relief Procedure Follow this Pressure Relief Procedure whenever instructed to relieve pressure, stop spraying, check or service equipment, or install or clean spray tip. 1. Turn OFF power and turn sprayer pressure control to low-est pressure setting. 2. Hold gun against side of fl...
Parts 311861G 3 Aligning Spray 1. Relieve pressure. Set trigger lock (2). Loosen guard retaining nut. 2. Loosen guard retaining nut. 3. Align guard (25) horizontally to spray a horizontal pattern. 4. Align guard (25) vertically to spray a vertical pattern. Clearing Clogs 1. Relieve pressure. Set tri...
For complete warranty information contact your Graco distributor, call Graco customer service: 1-800-690-2894 or visit our website: www.graco.com All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the ri...
