Graco 24R200 - Manual

Component Identification 332511A 5 Heat Controller Key: AA Current TemperatureAB Power is Supplied to HeaterAC Power is Supplied to Heat Overtemp ContactorAD Desired TemperatureAE Temperature Adjustment F IG . 2: Heat Controller 70 90 1 2 AA AB AC AD AE

Installation 6 332511A Installation Grounding Ground the system as instructed within this manual. 1. Access the Platen a. Perform Change Drums procedure in the Air-Powered Ram manual. Do not load a new drum. b. Perform Shutdown procedure in the Exact- aBlend AGP Advanced Glazing Proportioner, Setup-...

Installation 332511A 7 2. Install the Heat Coils and the Thermostat Switch. 3. Connect the Ground Wires. Connect the ground wires to the terminal lug and to the platen covers (not shown in view). Attach the conduit to the platen cover and route the wires through the conduit when connections are comp...

Installation 332511A 11 9. Route the Power Cord and Signal Cable to the Junction Box. Secure the power cord and signal cable to the base (A) cross bar. 10.Connect the Leads in the Junction Box. Connect “A” leads, “B” leads, ground, and signal cable within the junction box. Replace the cover. Routing

Installation 12 332511A 11.Connect the Power Cable from the Heat Electrical Enclosure to the Main Electrical Enclosure. 12.Connect Power to the Terminals and Ground.

Setup 332511A 13 Setup 1. Turn the power on at the heated platen electrical enclosure. 2. Turn the power on at the heater power switch. 3. Set the desired platen temperature by pressing either the up or down arrow keys. NOTE: Temperature is displayed in Fahrenheit. 70 90 1 2 Desired Temperature

Operation 14 332511A Operation Startup 1. Turn the power on at the heated platen electrical enclosure. 2. Turn the power on at the heater power switch. 3. Set the desired temperature. Refer to page 5 for details. Shutdown 1. Turn the power off at the heater power switch. NOTE: If the entire machine ...

Maintenance 332511A 15 Maintenance Platen Maintenance If the platen does not come out of the pail easily when the pump is being raised, the air assist tube or check valve may be plugged. A plugged valve prevents air from reaching the underside of the plate to assist in raising it from the pail. 1. T...

Troubleshooting 16 332511A Troubleshooting Before performing any troubleshooting procedure: 1. Perform Pressure Relief Procedure In the Exact- aBlend AGP Advanced Glazing Proportioner, Setup-Operation manual. 2. Turn off main disconnect at the machine. 3. Allow equipment to cool. Try the recommended...

Repair 18 332511A Repair Replace Platen Heaters and Sensor 55 Gallon Platen Heater and Sensor 1. Turn off main disconnect at the machine. 2. Allow equipment to cool. 3. Remove both platen cover fasteners (F). 4. Remove both platen covers (C) and ground wire from platen. 5. Remove platen heater block...

Schematic 332511A 19 Schematic 140 149 147 145 142 110 138 136 134 132 130 128 126 124 122 120 118 114 116 112 108 106 104 102 100 141 148 144 146 143 111 139 137 135 133 131 129 127 125 123 121 119 115 117 113 109 107 105 103 101 50-60HZ 1PH/ 220V/ DISC100 L2 1L2 L1 1L1 GND CB CB 1L1 1L2 CB CB 1L1 ...

Parts 20 332511A Parts Heated Platen Kit, 24R200 F IG . 5: Heated Platen Kit 14 11 5, 26 6 2 2 3 5 22 23 28 11 7 14

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual contains Eng...