Page 2 - Table of Contents
2 3A2090A Operation Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Component Identification (Sprayer) . . . . . . . . . . . 6 Component Identification (Controls) . . . . . . . . . . . 7 Grounding Procedure (For Flammable Materials Only) . . . . . . . ....
Page 3 - Warnings; WARNING
Warnings 3A2090A Operation 3 Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these sym-bols appear in the body of ...
Page 11 - SwitchTip and Guard Assembly
Setup/Startup 3A2090A Operation 11 14. Increase pressure control enough to start pump. Allow fluid to circulate for 15 seconds. 15. Turn pressure down, turn prime valve horizontal. Disengage gun trigger safety. 16. Hold gun against grounded metal flushing pail. Trig- ger gun and increase fluid press...
Page 12 - Gun Placement; Install Gun; Position Gun
Gun Placement 12 3A2090A Operation Gun Placement Install Gun 1. Insert gun into gun holder. Tighten clamp. Position Gun 2. Position gun: up/down, forward/reverse, left/right. See Gun Positions Chart, page 17 for examples. 3. Use the Gun Selector Switches to determine which guns are active. Each gun ...
Page 13 - Gun Arm Mounts; Removal
Gun Placement 3A2090A Operation 13 Gun Arm Mounts This unit is equipped with front and rear gun arm mounts. Change Gun Position (Front and Back) 1. Loosen gun arm knob and remove from gun arm mounting slot. 2. Slide gun arm assembly (including gun and hoses) out from gun arm mounting slot. 3. Slide ...
Page 14 - Installation
Gun Placement 14 3A2090A Operation 3. Loosen gun mounting wing nut and remove gun mount. 4. Slide gun arm assembly out from gun arm mounting slot. Installation 1. Slide gun arm assembly into gun arm mounting slot. 2. Install gun mount onto gun arm assembly and tighten gun mount wing nut. 3. Tighten ...
Page 15 - Gun Cable Adjustment; Adding Gun Cable
Gun Placement 3A2090A Operation 15 Gun Cable Adjustment Adjusting the gun cable will increase or decrease the gap between the trigger plate and the gun trigger. To adjust trigger gap, perform the steps below. 1. Use wrench to loosen locking nut on cable adjuster. 2. Loosen or tighten adjuster until ...
Page 16 - Change Trigger Position
Gun Placement 16 3A2090A Operation Change Trigger Position Removal 1. Remove both hand grips from handle bar (spraying compressed air into end of handle grip works well for this). 2. Use an allen wrench to loosen bolt on trigger mount-ing clamp. 3. Remove trigger assembly from handle bar. Installati...
Page 17 - Gun Positions Chart
Gun Placement 3A2090A Operation 17 Gun Positions Chart 1 One line 2 One line up to 24 in. (61 cm) wide. 3 Two lines 4 One gun curb 5 Two gun curb ti18553a 2 3 4 5 1
Page 18 - Driving Instructions; Parking / Emergency Brake
Driving Instructions 18 3A2090A Operation Driving Instructions Perform Startup, page 9. Use the handle bars of the LineStriper to control all motion during operation. In addition to steering the LineStriper, the handle bars also control forward and reverse movement by pulling the forward/reverse con...
Page 19 - Drive Engagement; Handle Bar Height Adjustment
Driving Instructions 3A2090A Operation 19 Drive Engagement The wheel motor bypass valve allows the operator to disengage the wheel tension and push the unit around. Rotate one complete turn counter-clockwise to disengage. Straight Line Adjustment The front wheel is set to center the unit and allow t...
Page 20 - Platform Storage Position; Front Pad Adjustment
Driving Instructions 20 3A2090A Operation Platform Storage Position 1. Raise stand and pin self-locks. 2. To lower stand, pull pin and lower stand. Front Pad Adjustment 1. Loosen four bolts. 2. Slide pad up or down to desired position. 3. Tighten four bolts. ti18560a ti18566a ti19006a 4 bolts
Page 21 - Smart Control Overview; Quick Guide
Smart Control Overview 3A2090A Operation 21 Smart Control Overview Quick Guide
Page 22 - Smart Control Operation; Initial Setup; Calibration
Smart Control Operation 22 3A2090A Operation Smart Control Operation Initial Setup 1. Select appropriate language. ENG = EnglishSPA = SpanishFRE = FrenchDEU = German NOTE: Languages can also be changed later. 2. Select appropriate units of measure. US Units Pressure = psiVolume = gallonsDistance = f...
Page 23 - Calibration Error Displays
Smart Control Operation 3A2090A Operation 23 6. Press SETUP twice to move to CALIBRATION & UNITS display. Set TRAVEL DISTANCE to 25 ft. Longer distances ensure better accuracy, depend-ing on conditions. \ 7. Align calibration bar rear edge with 1 foot on steel tape. 8. Push gun trigger control t...
Page 24 - Change Units or Language
Smart Control Operation 24 3A2090A Operation Change Units or Language 1. Press SETUP twice to move to CALIBRATION & UNITS display. Select CHANGE UNITS. 2. While in CHANGE UNITS display, press CHANGE to change units or NEXT to move to the next unit of measure. Press SETUP to exit CHANGE UNITS mod...
Page 25 - Operation in Manual Mode; Preset Skip Patterns
Smart Control Operation 3A2090A Operation 25 Operation in Manual Mode 1. Make sure engine is running and main power switch is on. 2. Use Gun Selector Switches to select guns and line type. 3. Press and hold Gun Trigger Control button to spray a line. Release button to stop spraying. Operation in Aut...
Page 26 - Advanced: Preset Skip Patterns
Smart Control Operation 26 3A2090A Operation Advanced: Preset Skip Patterns 1. A Preset Skip Pattern can be modified for a custom pattern. From AUTO MODE press SETUP key to get preset patterns. 2. Use SELECT arrow keys to choose which preset pattern you wish to modify. Use EDIT arrow keys to get PAI...
Page 27 - Parking Layout Mode; Basic Stalls
Smart Control Operation 3A2090A Operation 27 Parking Layout Mode NOTE: Please use the 286111 tip provided with striper for parking lot layout work. For best performance set pressure to 1000 psi (68.9 bar, 6.89 MPa) and reverse tip. Parking Mode Basic Stalls From MANUAL MODE press MODE button twice f...
Page 28 - Angle Stalls
Smart Control Operation 28 3A2090A Operation Angle Stalls 1. Angle stalls require the operator to input stall angle and depth. The Auto-Layout System calculates the offset distance based on this input. 2. From PARKING LAYOUT MODE press SETUP two times for ANGLE CALC. 3. ANGLE: Press and hold Gun Tri...
Page 29 - Marker Mode
Smart Control Operation 3A2090A Operation 29 Marker Mode 1. Press the MODE key to select Parking Layout Mode. 2. Press SETUP three times to select Marker Layout Mode. 3. Use SELECT and EDIT keys to set up reflective marker pattern. Automatic marker layout example shows typical lane line layout for r...
Page 30 - Measure Mode; Machine Information
Smart Control Operation 30 3A2090A Operation Measure Mode 1. Press SETUP once from Manual Mode display. 2. Press Gun Trigger Control and move striper forward or backward (back ward is a negative distance). 3. Press Gun Trigger Control to end measured length. Up to six lengths are viewable. NOTE: The...
Page 31 - Cleanup
Cleanup 3A2090A Operation 31 Cleanup 1. Perform Pressure Relief Procedure, page 8. 2. Remove guard and SwitchTip. 3. Unscrew cap, remove filter. Assemble without filter. 4. Clean filter, guard and SwitchTip in flushing fluid. 5. Place siphon tube set in grounded metal pail par-tially filled with flu...
Page 32 - Hydraulic Oil/Filter Change
Hydraulic Oil/Filter Change 32 3A2090A Operation Hydraulic Oil/Filter Change Removal 1. Relieve pressure, page 8. 2. Place drip pan or rags under sprayer to catch hydraulic oil that drains out. 3. Remove drain plug. Allow hydraulic oil to drain. 4. Unscrew filter (227) slowly - oil runs into groove ...
Page 33 - Technical Specifications
Technical Specifications 3A2090A Operation 33 Technical Specifications Wetted Parts: PTFE, Nylon, polyurethane, V-Max, UHMWPE, fluoroelastomer, acetal, leather, tungsten carbide, stainless steel, chrome plating, nickel-plated carbon steel, ceramic LineLazer IV 250 SPS (Models 24F307, 24K960, 24K961,...
Page 34 - Notes
Page 36 - Graco Standard Warranty
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual contains Eng...
