Graco 221619 - User Manual
Graco 221619 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Specifications
- Page 3 – Warnings
- Page 4 – WARNING
- Page 7 – Installation; Thermal Overload
- Page 8 – Component Identification
- Page 10 – Operation; Trigger Lock; Pressure Control Knob Settings
- Page 11 – Setup; Prime and Flush Storage Fluid; Strain the Paint
- Page 13 – Install Tip and Guard on Gun; Preventing Excessive Tip Wear
- Page 14 – Adjust Spray Pressure; Unclogging Spray Tip
- Page 15 – Tip Selection; Selecting Tip Hole Size; Choosing the Correct Tip; Tip Hole Size; Fan Width
- Page 16 – Understanding Tip Number; Reversible Tip Selection Chart; Tip
- Page 17 – Getting Started With Basic Techniques; Triggering Gun
- Page 18 – Shutdown and Cleaning; Pail Flushing
- Page 20 – Power Flush; OPEN
- Page 22 – Cleaning InstaClean; Cleaning Gun
- Page 23 – Storage; Short Term Storage; Long Term Storage
- Page 24 – Stowing Sprayer
- Page 25 – Maintenance and Service; Caring for Sprayer; Pump Packings
- Page 26 – Troubleshooting; Problem
- Page 32 – Technical Data
- Page 34 – Graco Standard Warranty
313034J
EN
Operation
LTS 15, LTS 17, ProLTS 17 and ProLTS 19
Airless Sprayers
-
For portable spray applications of architectural paints and coatings. For professional use only-
Models 257060, 257065, 24N906, 24N808
3000 psi (21 MPa, 207 bar) Maximum Working Pressure
See page 2 for model and series information including
dispense rate, recommended hose length, guns, and
maximum working pressure.
IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this
manual and related manuals. Be familiar
with the controls and the proper usage of
the equipment. Save these instructions.
Related Manual:
313036 - Repair
ti11304a
Model: 257060
M
AGNUM
LTS 15
M
AGNUM
LTS 17
Model: 257065
M
AGNUM
P
RO
LTS 17
Model: 24N906
M
AGNUM
P
RO
LTS 19
Model: 24N808
ti11305a
ti9369b
ti9368b
FIRE AND EXPLOSION HAZARD
•
Use only non-flammable or water-based materi-
als, or non-flammable paint thinners. Do not use
materials having flash points lower than 100°F
(38°C). This includes, but is not limited to, ace-
tone, xylene, toluene, and naphtha. For more
information about your material, request Safety
Data Sheet (SDS) from the supplier.
•
Spraying flammable or combustible materials in
a factory or fixed location must comply with
NFPA 33 and OSHA 1910.94(c) requirements in
the USA and with all similar local regulations in
other countries.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Graco 221619
Summary
Specifications 2 313034J Specifications This equipment is not intended for use with flammable or combustible materials used in places such as cabinet shops or other “factory”, or fixed locations. If you intend to use this equipment in this type of application, you must comply with NFPA 33 and OSHA r...
Warnings 313034J 3 Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-spe...
Warnings 4 313034J WARNING WARNING WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help pre- vent fire and explosion: • Do not spray or clean with materials having flash points lower than 100°F (38°C). Use only non-flammable ...
