Graco 17A223 - User Manual

Sprayer Safety Information 6 334179A Sprayer Safety Information The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear i...

Component Identification 334179A 9 Component Identification A B C D E F G H P N L Prime Pump Spray J M ti24625a K A Cup Cover B FlexLiner C Cup Support D VacuValve Cap E VacuValve Air Hole F VacuValve Reservoir G Strainer H Spray Tip Holder J Prime Pump/Spray Knob K Power Cord L Sprayer Trigger M Du...

Start Up 10 334179A Start Up Starting a New Job If you are using the sprayer for the very first time, see Flushing a New Sprayer , page 20. Stir material according to manufactures recommendations. If material was previously opened, it is recommended to strain material to avoid spray tip clogs.1. Ins...

Start Up 334179A 11 4. The VacuValve is an important part of your new sprayer. It is used to evacuate the air out of the FlexLiner. Open VacuValve cap. 5. Tilt the sprayer so the VacuValve is the highest point, causing any air in the FlexLiner to rise to the VacuValve. Gently squeeze the FlexLiner t...

Start Up 12 334179A 10. Make certain spray tip is in the spray position. 11. You are now ready to spray. If sprayer does not spray, try one of the steps below: • Make certain there is only one FlexLiner in cup support. It is possible for two liners to nest tightly together and appear as only one. • ...

How to Spray 334179A 13 How to Spray Take a few moments prior to spraying and review these simple tips to ensure your spraying project is a success. Dual Speed Control (Not available on all units) The speed control feature allows you to slow down or speed up when spraying. • Turn the dual speed cont...

How to Spray 14 334179A Triggering Sprayer Pull trigger after starting stroke. Release trigger before end of stroke. Sprayer must be moving when trigger is pulled and released. Aiming Sprayer Aim sprayer at bottom edge of previous stroke, overlapping each stroke by half. Rotating the spray tip guard...

Cleanup 334179A 15 Cleanup Pressure Relief Procedure Follow the Pressure Relief Procedure whenever you see this symbol. 1. Disconnect power (unplug power cord). 2. Turn Prime Pump/Spray Knob down to PRIME PUMP position to relieve pressure. Cleaning Sprayer Cleaning your sprayer properly and after ev...

Cleanup 334179A 17 13. Remove cup assembly and discard used fluid. Dispose of used cleaning fluid properly. 14. Replace cleaning fluid and repeat steps 1- 13 until spray output is clean. IMPORTANT! For best results, do not spray more than one cup of water through the tip while cleaning. If more flus...

Storage 18 334179A Storage Pump Armor fluid protects the sprayer while in storage. It helps protect sprayer against freezing and corrosion when not in use.1. Clean the sprayer and cup assembly. See Cleanup , page 15 . 2. Turn Prime Pump/Spray knob down to the Prime Pump position. Remove cup support ...

Common Procedures 334179A 19 Common Procedures Installing Spray Tips Two spray tips are available for use with this sprayer. The black tip produces a 12-inch wide spray pattern. The gray tip produces a 4-inch wide spray pattern. Either spray tip may be used to spray materials that are recommended to...

Common Procedures 20 334179A Unclogging Spray Tip In the event that particles or debris clog the spray tip, this sprayer is designed with a reversible spray tip that quickly and easily clears the particles without disassembling the sprayer. 1. Perform Pressure Relief Procedure , page 15 . 2. To uncl...

Replacement Parts 334179A 23 ti23568a 26 Replacement Parts Models 16Y391, 16Y392 8 19 19 20 13b 12 7 8 5 1 10 2 6 3 4 9 18 17 16 14 15 13a 22 24 ti24627a

Troubleshooting 334179A 25 Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. Sprayer Diagnostics ti24021a Have a Question? Call toll-free: 1-888-541-9788 Or visit us at: www.paintsprayersbygraco.com Problem Cause Solution Spr...

Technical Data 30 334179A Technical Data The vibration value has been measured in accordance with a standard test method and may be used for comparing against electric tools and for preliminary assessment of exposure. Hand-Held Sprayer U.S. Metric Max Working Pressure TrueCoat 360 1200 psi 8.3 MPa, ...

Graco Limited Warranty 334179A 31 Graco Limited Warranty Graco warrants to the original purchaser that this product will be free from defects in material and workmanship for one (1) year from the date of purchase when operated and maintained in accordance with Graco's written recommendations and ins...