Graco 114903 - Manual
Graco 114903 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation Instructions
- Page 3 – Injector Service Parts; Available Kits
- Page 4 – Plastisol cap for Graco GL-1 Injectors
- Page 5 – Technical Data
- Page 6 – Graco Standard Warranty; Graco Information
For Single–Line Parallel Automatic Lubrication Systems.
GL-1 Injector Models
Important Safety Instructions
Read all warnings and instructions in this manual and related automatic
lubrication system instruction manuals. Save all instructions.
SKIN INJECTION HAZARD
Fluid from the injector, leaks, or ruptured components
can inject fluid into your body and cause extremely seri-
ous injury, including the need for amputation. Fluid
injected into the skin might look like just a cut, but it is a
serious injury.
Get immediate surgical treatment.
Fluid splashed in the eyes or on the skin can also
cause serious injury. The equipment may be pressur-
ized already, or it could become pressurized by an
automatic lube cycle initiated by Lubrication Controller
(timer). Disconnect power to the timer, and disconnect
the air supply to the pump module to ensure that the
system is depressurized.
See the pressure relief pro-
cedure in the pump manual incuded with your auto-
matic lubrication system.
Part No.
Description
Dimension A
Dimension B
Bare Manifold Part No.
114901
Injector, GL–1, one point
2.48 in. (63.0 mm)
114911
114902
Injector, GL–1, two point
3.00 in. (76.0 mm)
114912
114903
Injector, GL–1, three point
1.25 in. (31.7 mm)
4.23 in. (107.5 mm)
114913
114904
Injector, GL–1, four point
2.50 in. (63.4 mm)
5.47 in. (139.0 mm)
114914
114905
Injector, GL–1, five point
3.75 in. (95.1 mm)
6.71 in. (170.5 mm)
114915
117206
Injector, GL-1, six point
4.99 in. (126.8 mm)
7.90 in. (202.7 mm)
118206
114909
Injector, GL–1, replacement
1-1/4”
7-1/16”
A
B
1/8” npt
dispense
outlet
13/32”
mounting
holes
3/8” npt
(2) supply
inlet/outlet
Model 114903 Shown
Instructions-Parts List
GL-1
®
Injectors
308953N
EN
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 308953N Installation Instructions Reference letters used in the following instructions, refer to F IG . 2. • Group injectors to minimize feed line length. • Install injectors in locations that allow easy and safe servicing access. • Install injectors in areas that minimize accidental injector dama...
Injector Service Parts 308953N 3 Injector Service Parts Available Kits Use Only Genuine Graco Repair Parts Graco Part No. 115119 . . . . . Plastisol Injector Cover (see page 3 for installation instructions) Graco Part No. 115120 . . . . . . . . . . . . . Crossover Kit (for connecting the outlets of ...
Injector Cover Kit 115119 4 308953N Injector Cover Kit 115119 Plastisol cap for Graco GL-1 Injectors Installation Instructions 1. Apply a light coating of transparent lubricant to the inside of cap (21). 2. Slide cap (21) over the indicator stem of the injector far enough to cover the groove in the ...
