GE ZV48R User Manual - Free PDF Download

Page 3 - Installation Instructions; PRODUCT DIMENSIONS

3 12" 22-1/2" 35-15/16" 35-15/16" 25" 10" Installation Instructions PRODUCT DIMENSIONS Model ZV36R Model ZV48R Model ZV30R CONTENTS Product Dimensions ......................................................... 3Installation Clearances .............................................

Page 4 - Advance Planning; INSTALLATION CLEARANCES; Installation with Warming Shelf; Installation without Warming Shelf

4 Advance Planning INSTALLATION CLEARANCES These vent hoods are designed to be installed onto awall or beneath a soffit or cabinet. Installation with Warming Shelf • Hoods must be installed 32" Min., 38" Max over any type cooking surface when warming shelf is used. Installation without Warmi...

Page 5 - DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES

5 Advance Planning DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES Restaurant-Style Hoods Restaurant-Style Hoods without Warming Shelf Installed with Shelf Installed 1 *Possible *Possible Actual Hood Hood Ceiling Installation 6" Duct 12" Duct Installation 6" Duct 12" Duct Heigh...

Page 6 - ADVANCE PLANNING; Ductwork Planning; POWER SUPPLY; IMPORTANT; AVERTISSEMENT–; Electrical supply; AVERTISSEMENT

6 Advance Planning ADVANCE PLANNING Ductwork Planning • These vent hoods are equipped for 10" round ductwork. For best performance, use 10" roundductwork on the 48" wide hoods. 30" and 36" hoodsmay be transitioned to 8" round. • This hood may be vented vertically through uppe...

Page 7 - DUCT FITTINGS; Hoods Are Equipped

7 Advance Planning DUCT FITTINGS Equivalent Quantity Total Duct Piece Length* Used Length 10" roundto 8" round 5 ft. Round, 1 ft. straight (per foot length) 90 ° elbow 8" Dia. 52 ft.10" Dia. 24 ft. 45 ° elbow 8" Dia. 31 ft.10" Dia. 14 ft. Round 8" Dia. 99 ft. wall cap 10&...

Page 8 - Installation Preparation; REMOVE THE PACKAGING

8 Installation Preparation REMOVE THE PACKAGING • Remove packages from the “V” shaped cardboard section. Remove shipping pads. • Lift the hood out of the box. IMPORTANT: Lift the hood by grasping the outside edges of the exhaust opening on the top. • The vent hood motor is shipped secured to the ski...

Page 9 - PARTS PROVIDED

9 PARTS PROVIDED Locate the parts packed with the hood. 2 Stainless Steel Grease Filters (3 filters with 48" models) Allen Wrench For Implement Rods Installation Preparation Duct Transition with Damper Backguard 2 Implement Rods and 4 Stand-offs Heat Lamp (2 with 48" models) 10 Phillips head...

Page 10 - STEP 1 DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS; FOR DUCTING THROUGH REAR WALL:; House Wiring Location:; Alternate Knockout Locations (for soffit installation)

10 • Use a level to draw the cooktop centerline location. Draw the line to ceiling height. • Measure desired distance from the bottom of the hood to the cooking surface. Note: If you are installing the hood with duct covers, be sure to read “Using Duct Cover Accessories” page 7. Exact installation h...

Page 11 - STEP 2A INSTALL HOOD ONTO WALL; Test Duct Cover Fit; Hang Hood On Wood Support; Install Transition Onto Top of Hood

11 1/4" Gap Original Mounting Screws as Shipped Installation Instructions STEP 2A INSTALL HOOD ONTO WALL • Secure the wood support to 2 or more vertical studs, using at least 2 of the 4 supplied long screws. IMPORTANT: Screws must penetrate at least 1-1/2" into vertical studs. Countersink sc...

Page 12 - STEP 2B Alternate Mounting Method; INSTALL HOOD TO SOFFIT OR BENEATH CABINETS

12 Installation Instructions STEP 2B Alternate Mounting Method “A” “B” Centerline to Stud Hood Width and Keyhole Slots At the Top ZV48R 23-9/16" 47-15/16" ZV36R 17-9/16" 35-15/16" ZV30R 14-9/16" 29-15/16" INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIP THIS STEP IF USING WALL...

Page 13 - STEP 3 CONNECT DUCTWORK; Verify that power is turned off at the source.; AVERTISSEMENT –; STEP 6 INSTALL MOTOR

13 Installation Instructions STEP 3 CONNECT DUCTWORK • Install ductwork, making connections in direction of airflow as illustrated. • Secure joints in ductwork with sheetmetal screws.• Wrap all duct joints with duct tape for an airtight seal. • Use duct tape to seal the flange connection.Reach insid...

Page 14 - STEP 7 INSTALL FILTERS; INSTALL SHELF OVER BACKGUARD:

14 Installation Instructions STEP 7 INSTALL FILTERS • To remove the filters, grasp the latch, pull the filter up and lift out. • Drop grease tray into the hood. The rear tabs should engage the slots in the hood track. STEP 8 INSTALL BACKGUARD AND SHELF This hood can be installed with thewarming shel...

Page 15 - STEP 10 INSTALL IMPLEMENT

15 Installation Instructions STEP 10 INSTALL IMPLEMENT RODS • Use a flat blade screwdriver to install stand-offs into the bottom of the hood. • Align implement rod to stand-offs with the screw hole towards the inside of the hood. Secure the rod to thestand-offs with the supplied Allen wrench. • Foll...