Page 2 - Safety Information; BEFORE YOU BEGIN; IMPORTANT; Note to Installer
Safety Information 2 BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep ...
Page 3 - Consignes de Sécurité; AVANT DE COMMENCER; IMPORTANT –; ATTENTION
Consignes de Sécurité 3 AVANT DE COMMENCER Veuillez lire toutes ces instructions attentivement. • IMPORTANT – Conservez ces instructions à l’usage de l’inspecteur local. Observez tous les codes et décrets en vigueur. • Note à l’installateur – Assurez-vous de laisser ces instructions au consommateur....
Page 4 - Contents
4 Contents Safety 2, 3 Instructions for Standard Installation 5-22 Planning Guide The Installation Space 6 Dimensions and Clearances 6 Customization Basics 7 Side Panels 7 Refrigerator Location 7 1/4” Framed Panel Dimensions 8 3/4” Overlay Panel Dimensions 9 130° Door Swing 10 90° Door Swing 11 Disp...
Page 5 - Instructions for Standard Installation
Page 6 - Design Guide - Standard Installation; THE INSTALLATION SPACE; Water And Electrical Locations; DIMENSIONS AND CLEARANCES; Product Clearances
B A Design Guide - Standard Installation THE INSTALLATION SPACE Water And Electrical Locations The opening must be prepared with the electrical and the cold water supply located as shown. The Cutout Depth Must Be 24” (60.96 cm) The refrigerator will project forward, slightly beyond adjacent cabinetr...
Page 7 - CUSTOMIZATION BASICS:; Optional Accessory Kits; SIDE PANELS
CUSTOMIZATION BASICS: These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels are required. 7 Optional Accessory Kits ZKHSS2: Monogram Tubular Stainless Steel handles designed to fit 3/4” (1.91 cm) overlay panels. ZKHPSS1: Professional ...
Page 8 - IMPORTANT NOTE – DISPENSER MODELS
1/4” (0.63 cm) FRAMED PANEL DIMENSIONS 8 If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door and grille. Non-Dispenser Models If the custom panel is less than 1/4” (0.63 cm) thick and it fits loosely in the door frame it ...
Page 9 - Assemble the panels with glue and screws:
36” Side-by-Side (in inches) Dispenser Cutout Position A B C D E F G 1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16 .10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4 3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-13/16 3-1/4 42” Side-by-Side (in inches) A B C D E F G 1/4” Backer Panel 39-7...
Page 11 - Dispenser trim; Frameless Cabinets:
1/4" 1/2" 3/4" 1" 1-1/4" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Overlay Panel (Nominal Size) Case Trim Refrigerator Door Stainless Steel Top View90° DOOR SWINGScale 1:1 IMPORTANT NOTE –FOR DISPENSER MODELS: Dispenser...
Page 13 - TOOLS AND MATERIALS REQUIRED; Installation Instructions - Standard Installation; HARDWARE SUPPLIED; GROUNDING THE REFRIGERATOR; WARNING; Electrical Shock Hazard.; MISE À LA TERRE DU RÉFRIGÉRATEUR; Risque de choc; FLOORING
13 TOOLS AND MATERIALS REQUIRED • Tinsnips to cut banding• Stepladder• 1” Bit extension• Tape measure• Gloves• 1/4” Drywall screws• 5-Gal. Bucket with cover• 6” Spirit level• Appliance hand truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16”...
Page 14 - STEP 1 REMOVE PACKAGING; Risque de; STEP 3 INSTALL WATER LINE; Raccordez l’appareil à une
Installation Instructions - Standard Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. The refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck, handle from the side only. AVERTISSEMENT Risque de basculement Le réfrigérateur est beauc...
Page 16 - STEP 7 LEVEL REFRIGERATOR; If you; STEP 8 ALTERNATE ANTI-TIP; The refrigerator must be secured to prevent tipping
16 STEP 7 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator.• To level the back of the refrigerator, turn the 7/16” hex nut located above the front wheels. T...
Page 17 - STEP 9 ADJUST DOOR SWING; Skip; STEP 10 INSTALL GRILLE PANEL; CAUTION; SHARP EDGE HAZARD; ATTENTION AUX ARÊTES VIVES
Installation Instructions - Standard Installation STEP 9 ADJUST DOOR SWING NOTE: This refrigerator has a 3-position door stop: 90°, 115°, and 130°. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. A 130° door swing option is available fo...
Page 19 - STEP 11A INSTALL OVERLAY PANELS; Dispenser Models Only:
STEP 11A INSTALL OVERLAY PANELS Install door panels: • Open door to 90°. Remove the 6 Phillips head screws from the door handle. • Remove the handle. Retain all screws.• Remove the 6 screws holding the trim, then lift off the trim. Retain the screws. • Slide the overlay panel into the door trim. Dis...
Page 20 - STEP 12 CONNECT WATER SUPPLY; SmartConnect; Custom Handles
STEP 12 CONNECT WATER SUPPLY • Locate and bring the tubing to the front of the cabinet. • Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the water. Copper Tubing: • Slip a 1/4” nut and ferrule (provided) over both ends of t...
Page 21 - STEP 14 START ICEMAKER; STEP 13 CONNECT POWER, CLOSE
21 STEP 12 CONNECT WATER SUPPLY (continued) Installation Instructions - Standard Installation STEP 14 START ICEMAKER CAUTION Avoid contact with the moving parts of the ejector mechanism, or with the heating element (located on the bottom of the icemaker) that releases the cubes. Do not place fingers...
Page 22 - INSPECT FINAL INSTALLATION
22 Installation Instructions - Standard Installation INSPECT FINAL INSTALLATION Check door alignment. Stand back away from the refrigerator to inspect the final installation.• Check to be sure the handles are evenly aligned with each other at the top. To adjust, loosen the handle screws and slide up...
Page 23 - Instructions for Flush Installation
Page 24 - Design Guide - Flush Installation
Design Guide - Flush Installation THE INSTALLATION SPACE Water And Electrical Locations The opening must be prepared with the electrical and the cold water supply located as shown. The Cutout Depth Must Be 26-3/16” (66.99 cm) Wooden cleats are required for flush installation. See Side Cleats on page...
Page 25 - CUSTOM HANDLE DESIGN GUIDE
CUSTOMIZATION BASICS: These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels are required. 25 Optional Accessory Kits ZKHSS2: Monogram Tubular Stainless Steel handles designed to fit 3/4” (1.91 cm) overlay panels. ZKHPSS1: Professional...
Page 26 - Panel Dimensions
26 Design Guide - Flush Installation 1/2” (1.27 cm) OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4” (0.63 cm) thick backer panel which slides into the trim. A spacer panel 0.10” (0.25 cm) thick must...
Page 27 - Door Trim Pinch Point Hazard
27 Design Guide - Flush Installation 36” Side-by-Side Fresh Food Freezer Grille Dispenser Cutout Position E F 3/4” Raised Panel 68-5/8” x 20-7/8” 68-5/8” x 16-7/8” 38” x 11-3/16” 17-23/32” 3-3/8” 42” Side-by-Side Fresh Food Freezer Grille Dispenser Cutout Position E F 3/4” Raised Panel 68-5/8” x 26-...
Page 30 - CUSTOM PANEL; SIDE CLEATS
30 DISPENSER TRIM FIT EXAMPLES:(NOT TO SCALE) CUSTOM PANEL • The dispenser trim fits over the custom panel and snaps into the freezer door. Custom Panel Ice / Water Dispenser FREEZER DOOR 3/4”Overlay Dispenser Trim Design Guide - Flush Installation SIDE CLEATS Wood cleats are required to be installe...
Page 31 - Installation Instruction - Flush Installation
31 TOOLS AND MATERIALS REQUIRED • Tinsnips to cut banding• Stepladder• 1” Bit extension• Tape measure• Gloves• 1/4” Drywall screws• 5-Gal. Bucket with cover• 6” Spirit level• Appliance hand truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16”...
Page 32 - Installation Instructions - Flush Installation; Connect to potable water supply
Installation Instructions - Flush Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. The refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck, handle from the side only. AVERTISSEMENT Risque de basculement Le réfrigérateur est beaucoup...
Page 34 - STEP 8 LEVEL REFRIGERATOR; If you attempt; STEP 7 ANIT-TIP PROCEDURE
STEP 8 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator.• To level the back of the refrigerator, turn the 7/16” hex nut located above the front wheels. Turn...
Page 35 - Skip this step if door
35 Installation Instructions - Flush Installation STEP 9 ADJUST DOOR SWING NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. A 130° door swing option is available for standard installati...
Page 36 - To insert the framed or overlay panel into the grille:
Installation Instructions - Flush Installation STEP 10 INSTALL GRILLE PANEL To insert the framed or overlay panel into the grille: • Raise the grille panel to the stop position. • Loosen the screws on the side trim behind the frame. Remove the bottom trim. Adjust Nut Below Spring to Accommodate Pane...
Page 37 - STEP 11 INSTALL OVERLAY PANELS; Custom handles must be used with flush inset.
STEP 11 INSTALL OVERLAY PANELS Install door panels: • Open door to 90°. Remove the 6 Phillips head screws from the door handle. • Remove the handle. Retain all screws.• Remove the 6 screws holding the trim, then lift off the trim. Retain the screws. • Slide the overlay panel into the door trim. • Cu...
Page 40 - STEP 15 INSTALL TOEKICKS
40 Installation Instructions - Flush Installation STEP 15 INSTALL TOEKICKS • Locate the supplied toekicks (shipped taped to the side of the refrigerator. • The wider set of toe kicks will be used for flush installation. You can discard the other set of toe kicks. • Attach the LARGER toekick to the r...
Page 41 - Instructions for Stainless Steel Installation
Instructions for Stainless Steel Installation 41 31-49171
Page 42 - Design Guide - Stainless Steel Installation
Design Guide - Stainless Steel Installation THE INSTALLATION SPACE Water And Electrical Locations The opening must be prepared with the electrical and the cold water supply located as shown. The Cutout Depth Must Be 24” (60.96 cm) The refrigerator will project forward, slightly beyond adjacent cabin...
Page 43 - Professional Style Stainless Steel Refrigerators; REFRIGERATOR LOCATION
CUSTOMIZATION BASICS: Professional Style Stainless Steel Refrigerators Stainless steel wrapped refrigerators have beveled edges and professional-style handles. These models are shipped ready for installation. Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped do...
Page 46 - Installation Instruction - Stainless Steel Installation
46 TOOLS AND MATERIALS REQUIRED • Tinsnips to cut banding• Stepladder• 1” Bit extension• Tape measure• Gloves• 1/4” Drywall screws• 5-Gal. Bucket with cover• 6” Spirit level• Appliance hand truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16”...
Page 47 - basculement; Shut off the main water supply.
Installation Instruction - Stainless Steel Installation STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. The refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck, handle from the side only. AVERTISSEMENT Risque de basculement Le réfrigérateur est...
Page 50 - STEP 10 CONNECT WATER SUPPLY; STEP 12 START ICEMAKER; STEP 11 CONNECT POWER, CLOSE
50 STEP 10 CONNECT WATER SUPPLY • Locate and bring the tubing to the front of the cabinet. • Turn the water on to flush debris from the line. Run about a quart of water through the tubing into a bucket, then shut off the water. Copper Tubing: • Slip a 1/4” nut and ferrule (provided) over both ends o...
Page 51 - STEP 13 INSTALL TOEKICKS
51 Installation Instruction - Stainless Steel Installation STEP 13 INSTALL TOEKICKS • Locate the supplied toekicks (shipped taped to the side of the refrigerator. • Attach the LARGER toekick to the refrigerator using ONLY the top center hole (1). • Attach the toekick skirt to the refrigerator using ...
