GE ZCG3300 Manual - Free PDF Download

Page 2 - This appliance must be properly grounded. See “Power Supply”, page 5.; Consumer Information Service at; Design Information; Contents; CAUTION; WARNING; MISE EN GARDE

Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions w...

Page 3 - White built-in compactor; base is adjustable from; If cord is to be plugged

3 Design Information Built-In Compactors Modelsavailable ZCG3500 SS Stainless steel built-incompactor ZCG3300 WW White built-in compactor ZCG3100 BB Black built-in compactor Note: This compactor is designed for built-in applicationsonly. Dimensions and clearances A – 34" (864 mm) adjustable to 3...

Page 4 - Installation Preparation

4 StandardAppearancePanelOptions The Monogram compactor models ZCG3300 and ZCG3100 come with a white/black reversible aluminum front drawer panel. Model ZCG3300 isshipped with the white panel showing and modelZCG3100 with the black side showing. The panels on both models can be reversed to reveal th...

Page 6 - Optional Materials; Installation

6 Tools required: • #2 Phillips head screwdriver • Flat blade screwdriver • Tape measure • Spirit level • 10" long 2x4 • Adjustable wrench or slip joint pliers • Drill and 1/8" drill bit Parts List: • 4 leveling feet caps • 4 Phillips head screws • 2 Slotted head screws • 2 Tip-over brackets...

Page 8 - If a custom toekick board; Tighten screws making sure base does not move.; If an alternate toekick depth

8 Step 1Determinetoekickdepth Place a section of the carton on the floor for protection. Lay the compactor on its back, supportingit with a piece of wood to prevent pressure on thepower cord. Measure the toekick of an adjacent cabinet, from the front of the cabinet door to the front of the toekick (...

Page 9 - If using a custom toekick, add that

9 Step 3Positioningthe compactorbackstop A backstop should be installed to prevent the compactor from “walking” back when the drawer is closed. Measure and mark 16" back from the front edge ofthe cabinet toekick. Cut a 2x4, 10" long and anchor to the floor. Note: If using a custom toekick, a...

Page 10 - • PLUG POWER CORD INTO THE WALL; Make certain that the

Compactor Top Countertop Overlap Step 5Attachtip-overbrackets Position tip-over brackets on the top of the compactor. Match hole #3 of the bracket to the screwhole on the compactor (the 3rd hole on the bracket is the standard location). Attach tip-over bracket tocompactor with one slotted head screw...

Page 11 - The custom toekick should

Step 5(continued) If the countertop cannot be drilled into, slip the 90°clips over the short leg of the bracket and screw intothe face of the cabinet. 11 To install custom toekick (not supplied) measure thefront of the compactor’s adjustable base and use thosedimensions to cut out your custom toekic...

Page 12 - • While supporting the weight of the drawer front,

12 Step 7Changingfront panel(ZCG3300 and3100 only) Remove compactor drawer by pulling it out until itstops. Then lift the drawer to clear second stop andremove drawer. Place drawer on its back. Procedure AReverse color panel Remove the two screws in the bottom edge of thetrim. Slide panel out, turn ...

Page 13 - Select screw length carefully to avoid penetration of the

13 Procedure C (continued) • Lay drawer front face down on a flat surface.• Remove 9 screws which retain the front panel and handle. – Save handle and galvanized inner door.– Discard front panel with side trim. • Place galvanized inner door onto the back side of the finished panel. • Position the in...

Page 15 - • Replace drawer front to the drawer by re-installing

15 Procedure D (continued) • Turn the panel over, appearance side up. Use wood blocks to support the inner door and preventdamage to the hinge and lock tabs. • Drill pilot holes through the front of the custom panel and through the metal panel to match thechosen handles. • Secure handle to wood pane...

Page 16 - For Monogram; Product improvement is a continuing endeavor at

Pub. No. 49-5778-4Dwg. No. 165D4700P19693042835C 10-03 JR Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. There...