GE Simon Security System - Manual

iii Sensor Tampered....................................................................................................................................... 24Option 50 Detected ...............................................................................................................................

Simon Security System 1 Introduction to Your Security System Your security system uses wireless technology to warn your family about intrusion, carbon monoxide and fire. It may also be used to control lights and appliances within your home. The system has the capabilities of communicating with a cen...

Simon Security System 2 Outdoor Motion Sensors detect motion in a protected outdoor area. When motion is detected, the system may respond by sounding chimes or turning on outside lights. These sensors are not used for intrusion detection. Door/Window Sensors detect the opening of a door or window. S...

Simon Security System 3 Keychain Touchpad Keychain Touchpads are handy for simple arming, disarming and light control func-tions. They are portable and can be carried off-site in a purse or pocket. Telephone Touchtone telephones can be used to communicate with your system while you are off-site. Ask...

Simon Security System 4 Entry Delay Entry Delay is the amount of time the system gives you to disarm the system after enter-ing the home (between 5 and 254 seconds). This is programmed by the installer. When you enter your home you will hear beeps during the entry delay (see the table “Status Beeps”...

Simon Security System 5 Note This feature is most likely used when there is no one on the premises. Panel announces, Motions on. Arm Motion Sensors light will be lit and the exit delay will begin. ¾ Activate Latchkey Feature 1. Press the Arm Motion Sensors button twice. 2. Enter Access Code (if need...

Simon Security System 6 HOME CONTROL The Home Control buttons are used to monitor activity within and around the home. They are not used for intrusion protection. If any of the Home Control buttons are pressed and a sensor or module is not associated (programmed) with this feature the panel will ann...

Simon Security System 7 Panel will announce, time activated light on . Time Lights button will be lit. ¾ Turn Time Activated Lights off: 1. Press Time Lights button . Panel will announce, time activated light off . Time Lights button no longer lit. Sensor Activated Lights Turn on designated lights (...

Simon Security System 8 EMERGENCY Press FIRE, POLICE, or AUX for 2 seconds (or press twice quickly) to call the central monitoring station and notify them of a non-medical call for help. How Your System Communicates to You Your system responds to you through the use of panel voice messages, status b...

Simon Security System 9 Alarm Sirens and Lamp Modules Exterior and interior sirens make 3 different alarm sounds on the premises, each indi-cating a different type of alarm. Sirens are programmed by the installer to time-out and stop sounding after a specified time. Use the following table to unders...

Simon Security System 10 Dialog QS 1500 Touchtalk Interactive Keypad With the addition of the QS 1500 Keypad, the user is able to hear the voice feedback that is heard at the control panel. This enables the user to hear voice feedback from remote locations (where the keypad is mounted). Canceling an...

Simon Security System 11 How to Use an Off-Site Phone You may use an off-site phone to arm/disarm your panel, turn lights on and off, check system status, or conduct an audio session (ask your installer if you have this feature). ¾ How to gain access to the Control Panel: Note You may have to perfor...

Simon Security System 12 Press twice to eliminate the pre-programmed entry delay. ARM Motion Sensors Note Depending upon how your dealer programmed your panel, you may be required to enter your access code to arm the system. Press Arm Motion Sensors button once to turn protection on for all Motion S...

Simon Security System 14 Figure 1. Opening the panel cover Programming Instructions Use the following instructions to access the programming buttons and programming decals. Note If Trouble Beeps are turned on, the panel will sound six trouble beeps every minute the panel cover is open. Ask your inst...

Simon Security System 15 • Test • Clock Set Press the appropriate button. 4. After pressing the appropriate button on the START MENU , the system voice will prompt you to use the MAIN MENU. The MAIN MENU includes the following buttons: • Light Control • Option # • Sensor/Remote • Access Code Press t...

Simon Security System 16 1. Open the cover of the panel. 2. The panel voice prompts you to Use numbered keys to enter ID. Enter your mas- ter access code using the numbered keys. 3. The panel voice prompts you to Please select from START MENU. Press the Delete button on the START MENU. 4. The panel ...

Simon Security System 17 Press Add in the START MENU and follow the voice prompts to turn an option on. Press Delete in the START MENU to turn an option off. When entering a single digit option number (1-9), you must type a zero before the number (i.e. 01, 02,.....). All option numbers must be 2 dig...

Simon Security System 18 3. Press Add from the Start menu. Panel announces, Select from main menu 4. Press Option #. Panel announces, Option 1, press again for next option or done to select. 5. Press 02 . Panel announces, Option 2, press again for next option or done to select 6. Press DONE . Panel ...

Simon Security System 19 4. Press Option # . Panel announces, Option 1, press again for next option or done to select. 5. Press 36 . Panel announces, Option 36, press again for next option or set hours and minutes, then press done. 6. Press Hours and Minutes to set the time. 7. Press DONE . Panel an...

Simon Security System 20 Delete disables chime voice. The panel will not announce which chime sensor has been tripped but will still chime 2 times for doors and 3 times for motion sensors when a given sensor is tripped. 1. Open panel cover. Panel announces, Use numbered keys to enter ID. 2. Enter Ac...

Simon Security System 21 Note The phone number is auto-matically stored after you’ve pressed 26 digits. You will not have to press DONE to store the number. If the number is less than 26 dig-its, then DONE must be pressed. 6. Enter a phone number with the numbered keys. Press Test to enter a pause i...

Simon Security System 22 4. Press Option # . Panel announces, Option 1, press again for next option or done to select. 5. Press 55. Panel announces, Option 55, press again for next option or done to select 6. Use the numbered keys to enter the desired volume setting (01-10). 7. Press DONE . Delete s...

Simon Security System 23 3. Press Add from the Start menu. Panel announces, Select from main menu . 4. Press Option # . Panel announces, Option 1, press again for next option or done to select. 5. Press 82. Panel announces, Option 82, press again for next option or use num- bered keys to enter optio...

Simon Security System 24 Sensor Failure This condition occurs if a sensor is not communicating with the panel. Status beeps will start and the SYSTEM STATUS button will light. Press the SYSTEM STATUS button to hear which sensor(s) failed. Perform sensor tests. It may be necessary for you to call you...

Simon Security System 25 Testing As an added safeguard, there are system tests you should do yourself on a regular basis. It is recommended that you test your system weekly. Testing Sensors You can test sensors one at a time to make sure they are sending strong signals to the panel. You should test ...

Simon Security System 26 Testing Communication Communication between your system, the central monitoring station, pager and your remote phone (voice event notification) should be tested at least once per week to make sure you have the proper telephone connection. ¾ To perform a phone test: 1. Open t...

Simon Security System 27 • If freeze or any environmental sensors are not located in areas where the appropri-ate condition can be detected. • If smoke does not reach a Smoke Sensor. For example, Smoke Sensors cannot detect smoke in chimneys, walls, roofs, or smoke blocked by a closed door. Sen-sors...

Simon Security System 28 • Notify the fire department from a neighbor’s phone. • Emphasize that no one should enter the premises if they hear sirens in the house. • If you arrive at the premises and hear sirens, do not enter. Call for emergency assis-tance from a neighbor’s phone. Your Floor Plan Us...

Simon Security System 31 Access Codes Master Access Code:______________________ Access Code 1:__________________________ Access Code 2:__________________________ Access Code 3:__________________________ Access Code 4:__________________________ Access Code 5:__________________________ Sensor Location...

How to … Control Panel Remote Handheld Touchpad Key Chain Touchpad Remote Phone Disarm theSystem Subdisarm theSystem Arm Only - Doors& Windows Arm Only –Motion Sensors Arm Doors,Windows &Motion Sensors Activate No EntryDelay Activate LatchkeyFeature Activate a PanicAlarm Check the SystemStat...