GE GTD72EBSN0WS - Installation Manual

This Installation Manual covers GE dryers, focusing on safety, ventilation, and proper setup for both gas and electric models. The guide emphasizes critical requirements such as outdoor venting, compliance with local building codes (e.g., Massachusetts gas regulations), and clearance specifications for different installation types–including alcove closets, mobile homes, and manufactured housing. It details tools, materials, and step-by-step procedures for connecting hoses, gas lines, electrical wiring, and exhaust ducts, including diagrams for visual guidance. Safety is central: warnings about fire risks from improper venting, explosion hazards with gas dryers, and electrical grounding requirements are highlighted throughout. The manual also addresses door reversal for solid and glass-panel models, ensuring proper assembly before operation.

Page 1 – Installation and Safety Requirements for Dryers
Page 2 – Dryer Unpacking and Water Hose Accessories
Page 3 – Gas Dryer Installation Clearance and Venting
Page 4 – Connecting Inlet Hoses to Steam Models
Page 5 – Gas Dryer Connection Tools and Safety Procedures
Page 6 – Gas Dryer Gas Supply and Elevation Adjustments
Page 7 – Step-by-Step Gas Dryer Gas Line Installation
Page 8 – Gas Dryer Leak Testing and Grounding
Page 9 – Electric Dryer Connection Materials and Ratings
Page 10 – Electric Dryer Wiring Methods and Grounding
Page 11 – Electric Dryer Wiring Configurations
Page 12 – Exhaust Duct Installation Guidelines
Page 13 – Ducting Length Calculations and Installation Methods
Page 14 – Exhaust System Preparation Checklist
Page 15 – Venting from Side or Bottom Installation
Page 16 – Final Dryer Installation and Start-up
Page 17 – Reversing Door Installation on Solid Door Models
Page 18 – Reversing Door Installation on Solid Door Models
Page 19 – Reversing Door Installation on Glass Panel Models
Page 20 – Reversing Door Installation on Glass Panel Models

Loading the manual

- Risk of Fire

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these instructions

and local codes.

•

DO NOT

install a clothes dryer with flexible plastic venting

materials. If flexible metal (semi-rigid or foil-type) duct is

installed, it must be UL-listed and installed in accordance

with the instructions found in “Connecting the Dryer

to House Vent” later in this manual. Flexible venting

materials are known to collapse, be easily crushed and

trap lint. These conditions will obstruct dryer airflow and

increase the risk of fire.

•

DO NOT

install or store this appliance in any location

where it could be exposed to water or weather.

• To reduce the risk of severe injury or death, follow all

installation instructions.

• Save these instructions. (Installers: Be sure to leave

these instructions with the customer.)

In the Commonwealth of Massachusetts,

the following installation instructions apply:

• Installation must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified

or licensed by the State.

• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not

exceed 4 feet.

FOR GAS DRYERS ONLY

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

–

Save these instructions for local electrical

inspector’s use.

IMPORTANT

–

Observe all governing codes and

ordinances.
• Install the clothes dryer according to the manufacturer’s

instructions and local codes.

• Note to Installer –

Be sure to leave these instructions

with the Consumer.

• Note to Consumer –

Keep these instructions for future

reference.

• Clothes dryer installation must be performed by a qualified

installer.

• This dryer

must

be exhausted to the outdoors.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance

is used near children.

• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above 50°F for

satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

• Service information and the wiring diagram are located

in the control console.

05-19 GEA

31-3000199

Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com

Dryers

Installation

Instructions

WARNING

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: GE
Model: GTD72EBSN0WS
Document type: Installation Manual
Language(s): English
Pages: 20
File size: 5.8 MB
Format: PDF

Other Manuals for GE GTD72EBSN0WS

User Manual

Summary

Page 1 - Installation and Safety Requirements for Dryers

Installation requires a qualified installer, venting must be to the outdoors, compliance with local codes is mandatory. Specific warnings address fire risk from improper venting and requirements for gas dryers regarding flexible connectors.

Page 2 - Dryer Unpacking and Water Hose Accessories

Procedures for unpacking the dryer, rough-in dimensions for various cubic foot models, and a list of recommended steam water hoses and accessories with corresponding part numbers.

Page 3 - Gas Dryer Installation Clearance and Venting

Safety requirements for gas dryer installation covering clearance specifications for alcove or non-alcove setups, guidelines for mobile homes, venting methods, duct material, and precautions against explosion hazards from improper venting.