Page 2 - A l l r i g h t s r e s e r v e d .; F I R S T E D I T I O N
C 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n Te l e p h o n e : 0 7 9 8 - 6 5 - 2 1 1 1 Te l e f a x : 0 7 9 8 - 6 5 - 4 2 0 0 Y o u r L o c a l A g e n t / D e a l e r A l l r i g h t s r e s e r v e d . P U B . N o . I M E - 5 6 0 9 0 - N F E L C O M 8 1 A / B ( T E N I ...
Page 5 - Table of Contents; SAFETY INSTRUCTIONS
Table of Contents SAFETY INSTRUCTIONS i 1. System Configuration and Equipment Lists 1-1 2. Mounting of Units 2-1 2.1 Antenna Unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2-1 2.2 Communication Unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2-9 2.3 T elephone ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・...
Page 8 - Complete Set
Complete Set 1-2 No Name Type Code No. Mass (kg) Qty Remarks 1 Antenna Unit IB-181 --- 95 1 2 Communication Unit IB-281 --- 15 1 3 Terminal Unit IB-581 --- 6 1 Class 1 only w/Installation Materials CP16-01140 (page 1-8) 4 Telephone FC755D1 --- 1.0 1 w/Installation Materials CP16-00511(page 1-11) 5 J...
Page 9 - Optional Equipment
Optional Equipment 1-3 No Name Type Code No. Mass (kg) Remarks 1 Facsimile PFX-50 --- 8.0 w/Inst. MaterialsCP16-00590 (page 1-13) 2 Received Call Unit IC-301 --- 0.5 w/Inst. MaterialsCP16-00700 (page 1-12) 3 Telephone FC755D1 --- 1.0 w/Inst. Materials 4 Modular Jack Box OP16-10 000-043-278 0.2 5 Mod...
Page 41 - Checking the Installation
2.10 Checking the Installation General Before turning on the system, check for proper installation, following the procedure shown below. Standard Equipment Communication unit Are all connectors firmly fastened?Is the copper strap firmly fastened? Junction boxes IB-312 Are all connections on the term...
Page 48 - Connect a ground wire between ship's superstructure and a; FURUNO
Changing the power fuse Change the power fuse according to input voltage as follows. Figure 8 AC-DC power supply unit PR-300, rear view Ground Connect a ground wire between ship's superstructure and a ficing screw on the PR-300. 4.3 AC/DC Power Supply Unit PR-300 4-2 Input Output 100/110 VAC 10 A 20...
Page 51 - similes; Application; End code; Code number
Setting up Tele- phones/Fac- similes Set up telephones and facsimiles according to call appli-cation desired. Application 1. Non-credit card call only: Only non-credit card call can be made; credit card call cannot be made. 2. Credit card call/non-credit card call: Both credit card and non-credit ca...
Page 52 - Connector fixng plate
4.5 DGPS An L-band DGPS receiver may be connected.This requires a connector fixing plate for DGPS. 1. Turn off the communication unit.2. Detach the cover.3. Detach the dummy plate from the rear panel. 4. Fasten the connector fixing plate (supplied) to the rear panel with the screws used to fix the d...
Page 56 - Insert tip of a mechanical pencid under plastic cover; Setting of Telephone; ON; PB; DP; DIAL
5.2 Setting of Telephone Change dialing format from dial to pushbutton as follows.(The handset should be hung in the hanger.) FC622SLIWG 1. Press the key. 2. Press the key. 3. Press the key to display "Pb." 4. Press the key again. FC755D1 1. Insert tip of a mechanical pencid under plastic co...
Page 58 - Attaching the Compass Safe Distance and Inmarsat B Seals
5.4 Attaching the Compass Safe Distance and Inmarsat B Seals Attach the compass safe distance seals (supplied with installation materials) for the units shown below. When the same units (for example: telephone, facsimile, etc.) are used for other than FELCOM 81, attach ""seals b to them to d...
Page 59 - Dial Mode; MODE Switch
5.5 Facsimile PFX-50 Setting Turn on the power while dialing [*], [1], [3] to initialize the PFX-50's memory. Change the dial mode to "push button" with the MODE switch. (Choose position "T". ) 5.5 Facsimile PFX-50 Setting 5-5 Dial Mode MODE Switch Chosse "T".
Page 60 - Booting up by; Personal Computer Connection
5.6 Personal Computer Connection You can use a personal computer as the terminal unit for the FELCOM81, by installing the contents of a program disk on the PC. Note: Basic knowledge of DOS commands is required. Requirement; Type : 16-501-091 Code No: 004-441-520 Booting up by disk drive 1. Format a ...
Page 61 - Key Operation; See next page.; File; Standby Display; Date
6. System Setup 6.1 Setting Up Overview Set up the terminal unit, editor screen and communication unit (Class 2). When there is no navigation input or gyro input, enter them manually referring to operator's manual. Turn on the Main Unit and Terminal Unit. After a while, the Main Menu, shown below, a...
Page 62 - Registering Answerback Code; Overview; Enter ship's answerback code at installation.; The answerback code cannot be changed once; Procedure; Press; How to enter; characters; Cursor
6.2 Registering Answerback Code (Class 1 only) Overview Enter ship's answerback code at installation. The answerback code cannot be changed once registered. Confirm the code before pressing the key. Procedure Press , and in this order at standby- display. How to enter Telex IMN No. 4 characters (9 d...