Furuno 851 MARK-2 - Manual

Furuno 851 MARK-2

Furuno 851 MARK-2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
Page: / 37

Table of Contents:

  • Page 2 – F I R S T
  • Page 3 – WARNING; Radio Frequency Radiation Hazard; SAFETY INSTRUCTIONS
  • Page 4 – ii; Use only the specified power cable.; CAUTION
  • Page 5 – iii; SYSTEM CONFIGURATION; Antenna Unit
  • Page 6 – iv; EQUIPMENT LISTS; Standard Supply
  • Page 7 – Mounting Methods for Antenna Unit
  • Page 8 – Figure 1-1 Antenna unit mounting methods; Fixing Holes in Mounting Platform; Figure 1-2 Coating the bottom of antenna radiator for
  • Page 9 – Mounting the Antenna Unit; Outside fixing holes; Figure 1-4 Location of rubber mat
  • Page 10 – Figure 1-5 Antenna unit; Figure 1-6 Fixing the antenna unit chassis
  • Page 11 – Figure 1-7 How to fasten antenna unit to mounting platform; OR
  • Page 12 – Fixing holes inside antenna unit; Figure 1-9 Antenna unit chassis, upper chassis separated
  • Page 13 – Connecting the Signal Cable; Figure 1-10 Antenna unit chassis, cover opened
  • Page 15 – Attach three EMI cores to the signal cable as shown below.; Figure 1-15 Antenna unit chassis, cover opened
  • Page 16 – Mounting Methods for Display Unit
  • Page 17 – Mounting the Display Unit; The display unit is designed to be mounted on a tabletop.; FIXING HOLES; Figure 1-17 How to mount the display unit
  • Page 18 – Remarks
  • Page 19 – Signal cable connection; base is inserted into the groove on the rubber cover.
  • Page 21 – Attaching OPTION Connector; remove the rear covers.; Figure 2-6 Display unit rear view
  • Page 22 – Connection of two NMEA equipments
  • Page 23 – Cover shield with steel mesh by cable ties.; Installation Check List; Is the signal cable secured against a mast or bulkhead?
  • Page 24 – Checking magnetron heater voltage; DO NOT touch; DANGER; Close the antenna cover and tighten the cover fixing screws.
  • Page 25 – Initial Adjustment of Picture; GAIN; A.C RAIN 00
  • Page 26 – Displaying the Installation Menus; Procedure; MAIN MENU; INSTALLATION SETUP 1; Figure 3-5 Installation setup menu 1
  • Page 27 – INSTALLATION SETUP 2; Figure 3-6 Installation setup 2 menu; Entering Initial Settings; Beep turns on or off the buzzer which sounds when a key is pressed.)
  • Page 28 – Heading Alignment; Display the Installation Setup 2 menu.; Figure 3-7 Installation setup 2 menu
Loading the manual

Installation Manual

MARINE RADAR MODEL 851 MARK-2

SAFETY INSTRUCTIONS ........................................................................................... i

SYSTEM CONFIGURATION ..................................................................................... iii

EQUIPMENT LISTS................................................................................................... iv

1. MOUNTING ........................................................................................................ 1-1

1.1 Mounting Methods for Antenna Unit ........................................................................................ 1-1

1.2 Fixing Holes in Mounting Platform ........................................................................................... 1-2

1.3 Fastening the Radiator to the Radiator Bracket ...................................................................... 1-2

1.4 Mounting the Antenna Unit ...................................................................................................... 1-3

1.5 Connecting the Signal Cable ................................................................................................... 1-7

1.6 Mounting Methods for Display Unit........................................................................................ 1-10

1.7 Mounting the Display Unit ...................................................................................................... 1-11

2. WIRING............................................................................................................... 2-1

2.1 Connections ............................................................................................................................. 2-1

2.2 Input/Output Data List .............................................................................................................. 2-3

2.3 Attaching OPTION Connector ................................................................................................. 2-4

2.5 Installation Check List .............................................................................................................. 2-7

3. ADJUSTMENTS ................................................................................................. 3-1

3.1 Checking magnetron heater voltage........................................................................................ 3-1

3.2 Initial Adjustment of Picture ..................................................................................................... 3-2

3.3 Displaying the Installation Menus ............................................................................................ 3-3

3.4 Entering Initial Settings ............................................................................................................ 3-4

3.5 Heading Alignment ..................................................................................................................

..... 3-5

3.6 Sweep Timing .......................................................................................................................... 3-6

PACKING LIST ....................................................................................................... A-1

OUTLINE DRAWINGS............................................................................................ D-1

INTERCONNECTION DIAGRAM .......................................................................... S-1

SCHEMATIC DIAGRAMS ........................................................................................ S-2

2.4

Connection of two NMEA equipments ........................................................................... .......... 2-6

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - F I R S T

C 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n T e l e p h o n e : 0 7 9 8 - 6 5 - 2 1 1 1 T e l e f a x : 0 7 9 8 - 6 5 - 4 2 0 0 Y o u r L o c a l A g e n t / D e a l e r A l l r i g h t s r e s e r v e d . P U B . N o . I M E - 3 4 9 0 0 - D M O D E L 8 5 1 M A R K - 2 ( ...

Page 3 - WARNING; Radio Frequency Radiation Hazard; SAFETY INSTRUCTIONS

i WARNING Radio Frequency Radiation Hazard The radar antenna emits electromagnetic radio frequency (RF) energy which can beharmful, particularly to your eyes. Never look directly into the antenna aperture from aclose distance while the radar is in operation or expose yourself to the transmittingante...

Page 4 - ii; Use only the specified power cable.; CAUTION

ii Do not open the equipmentunless totally familiar withelectrical circuits andservice manual. Only qualified personnel should work inside the equipment. Wear a safety belt and hardhat when working on theantenna unit. Serious injury or death canresult if someone falls fromthe radar antenna mast. WAR...

Other Furuno Models

All Furuno Other