Page 2 - IMPORTANT NOTICE; This manual is intended for use by native speakers of English.
IMPORTANT NOTICE • This manual is intended for use by native speakers of English. • No part of this manual may be copied or reproduced without written permission. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications are s...
Page 3 - SAFETY INSTRUCTIONS; WARNING; Safety Instructions for the Operator; CAUTION
SAFETY INSTRUCTIONS WARNING Do not open the equipment except toreplace paper. Only qualified personnel should workinside the equipment. Immediately turn off the power at theswitchboard if water leaks into theequipment or something is droppedinto the equipment. Continued use of the equipment can caus...
Page 4 - Safety Instructions for the Installer; Securely attach protective
Safety Instructions for the Operator (con't) WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. WARNING LABELA warning label is attached to the main unit. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealerabout replace...
Page 5 - OUTLINE; and selection of a desired frequency; CONTENTS
i Page 1. OUTLINE ・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1 1.1 Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1 1.2 List of Standard Components ・・・・・・・・・・・・・・・・・・・・・ 2 1.3 System Components ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3 2. OPERATION 2.1 Description of key ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 4 2.2 Contrast a...
Page 6 - ii; APPENDIX; Area map of existing stations
ii 4.6 Exchange of a recording paper ・・・・・・・・・・・・・・・・・・・ 23 5. SPECIFICATIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ SP-1 5.1 Receiver ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ SP-1 5.2 Recorder ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ SP-1 5.3 Automatic Control ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ SP-1 5.4 Power, Dimension ＆ ...
Page 7 - OUT LINE; Characteristics; for changing frequency of existing station.
1 １．OUT LINE FAX-410 is the high sensitive weather facsimile receiver using electronic scanning thermal head recording system. １．１ Characteristics (1) Electronic scanning with thermal head recording system provides clear image, quiet operation. (2) Pre-programmed all existing weather facsimile stati...
Page 9 - System Components; Coaxial cable
3 １．３ System Components 2.6m Whip antenna Main unit Antenna coupler,fax-5 To BK line To Grounding wire To Power supply Coaxial cable
Page 10 - OPERATION; .1 Description of key; PRG; SPD
- 4 - ２． OPERATION The unit, with antenna(s) and power supply, receives and records signal automatically by the control of APSS when desired channels have been set. ２ .1 Description of key Program key : For preparation to mode setting. One of following modes can be selected by pressing key and next,...
Page 12 - RCD; CH
- 6 - Channel key : For selection of channel mode from frequency mode, and for shift to the channel setting in the channel mode. For setting a channel, press key and enter channel number with three keys. The channel covers 000 ～ 406 (existent frequency) and 410 ～ 733 (new frequency). Clear key : For...
Page 13 - .2 Contrast and brightness; DIM
- 7 - ２ .2 Contrast and brightness Contrast of LCD display depends on the visual angle and the temperature and hence, be sure to adjust it with the contrast knob (see Fig. 1) for optimum result at the time of installation. The backlight brightness of the LDC can be adjusted in five stages by pressin...
Page 14 - SYNC
- 8 - within 2000.0 ～ 24999.9kHz). ２ . ３ .3 Start and stop of recording (1) Start Recording starts automatically (Start/Stop, Phase, Speed, IOC) by receiving the APSS signal. To start halfway of the received picture, press key once and automatic speed setting and auto-phasing mode are set. Then, rec...
Page 15 - R E V E R S E : O F F
- 9 - ２ . ３ . ６ Selection of reception mode The reception mode refers IOC, speed, and normal/reverse printing and modes. The former two (IOC and speed) are automatically selected by receiving the APSS signal and phase signal. For the latter two modes, desired ones should be selected manually. (1) Sp...
Page 17 - P U S H E K E Y
- 11 - receiver, 2 is for external receiver. Pressing the key after setting a key, completes the setting. ２ . ４ . ２ Setting of timer reception This unit has 16 booking functions and each timer is set as follows. Press key. Then the timer reception setting mode is set and the message is shown on the ...
Page 22 - RAM clearance function
- 16 - RAM CLEAR ！ ！ PU SH ENT KEY ２ . ４ . ８ RAM clearance function The unit has RAM to memorize the frequency data of the FAX transmitting stations in the world and to retrieve such data. Therefore, when a part or all of RAM data is deleted in error so that the initial data in ROM (data at th...
Page 23 - Operation with external receiver; External receiver
- 17 - ２ . ５ Operation with external receiver (1) External receiver When an external receiver is used, it should have a local oscillator with very good frequency stability. The A1 detected beat, a low-frequency output, can be monitored with the unit when the signal is supplied through receiver jack ...
Page 24 - Lubrication and Cleaning; Lubrication
- 18 - 3. Maintenance ３．１ Back-up battery This device uses a manganese lithium battery as a back-up battery. Please exchange to new one after using for 5 years. Ask to a service shop for replacing the back-up battery. ３．２ Lubrication and Cleaning (1) Lubrication Lubricate a paper sending gear with 1...
Page 25 - INSTALLATION; Blurred part
- 19 - ４． INSTALLATION ４．１ Main unit Install the TF-711 main unit on a plane desk or a solid and plane wall with 4 pcs. of screws and washers. Caution: A print may become blurred if the installation place is uneven. In that case, put some washers or suitable attachment to adjust the flatness as foll...
Page 26 - Wiring
- 20 - ４．２ Wiring 4.2.1 DC power supply built-in type Connect black wire to “-“ (negative), and red wire to “+” (positive). 4.2.2 AC power supply built-in type Operation voltage (100/115/200/230 VAC) is pre-set at factory in accordance with customer’s request. In case of changing operation voltage, ...
Page 27 - Connection of BK; Push knob; Terminal board
- 21 - ４．３ Terminal board Use terminal board on the rear panel of the main unit for the connection between BK, external receiver or decoder. Insert a connection wire in a terminal in the following ways. Note: Use connection wire with single core 0.4~1.0mmØ or standard twist core 0.3mm 2 ~0.7mm 2 . ４...
Page 28 - suitable for reception under 6 MHz.
- 22 - ４．４ Grounding A GND terminal is on the rear panel of the main unit. Be sure to ground the main unit using attached earth wire (3m KIV wire 50/0.45 with copper tube terminal). ４．５ Receiving antenna Following antennas are suitable to use as the receiving antenna for the FAX-410. A) Antenna coup...
Page 29 - Exchange of a recording paper; Press
- 23 - ４．６ Exchange of a recording paper (1) Remove the front cover, up the paper cutting plate, slide the paper feed lever in the direction of rear. (Ref. Fig.1) (2) Set the roll paper to the holder by pressing a paper guide ② to left side. (Ref. Fig.2) Note: The paper guide ② can be moved about 3c...
Page 31 - SPECIFICATIONS; Receiver
SP - 1 ５． SPECIFICATIONS ５．１ Receiver Reception : Synthesized double superheterodyne Frequency range : MF/HF 2.0000 ~ 24.99999 MHz Mode : F3C Selectivity : 2.0 kHz at –6 dB Number of channels : 315 channels Sensitivity : MF/HF 2µV at 20 dB SINAD Channel selection : Automatic or manual, digital with ...
Page 32 - TABLE OF FACSIMILE STATION; Table of pre-programmed frequencies and area map
SP - 2 TABLE OF FACSIMILE STATION Table of pre-programmed frequencies and area map This unit has a ROM (read only memory) which is pre-programmed 150 of existing frequencies of transmitting stations. Stations and frequencies are shown in the map and table respectively. This table is reference data a...
Page 33 - SP; FACSIMI
SP - 3 FR EQ UENC Y FR EQ U E NC Y [kHz] [kHz] 000 JM H JAP AN 36 22.5 050 3S D B EIJING 84 61.9 001 JM H JAP AN 73 05.0 051 3S D B EIJING 12831 .9 002 JM H JAP AN 13597 .0 05 2 3S D B E IJING 16903 .9 010 JJC MA LA YS IA 84 67.5 060 BDF S H A NGH A I 32 41.0 011 JJC MA LA YS IA 12745 .5 06 1 B DF S...
Page 40 - Layout diagram; eather Facsimile Receiver F
D - 2 Layout diagram M 207-P A C Power supply unit － OUT DC Power supply unit FUSE 12 － 24VDC 7A Selectable A C or D C when placing order W eather Facsimile Receiver F A X-410 BK IN EXT IN ＋ －＋ BK A F A F OUT ＋ － FAX-5 Active antenna coupler Option Whip antenna(2.6m) (M 205-P) 7C-2V 16m (5C-2V) 【 Ca...
