Furuno F A R - Manual

Furuno F A R

Furuno F A R – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
72 Page 72
73 Page 73
74 Page 74
75 Page 75
76 Page 76
77 Page 77
Page: / 77

Table of Contents:

  • Page 5 – iii; TABLE OF CONTENTS; INITIALIZATION AND ADJUSTMENT
  • Page 6 – iv; LIST OF INSTALLATION MATERIALS, ACCESSORIES AND SPARE PARTS; OUTLINE DRAWINGS
  • Page 7 – EQUIPMENT LISTS; Complete set
  • Page 8 – vi; Optional equipment
  • Page 9 – vii; AR-2835S System Configuration; Optional Supply
  • Page 13 – Mounting the Antenna Unit on the Mounting Platform; Siting considerations; CAUTION
  • Page 17 – Mounting the Display Unit; Before mounting the display unit
  • Page 19 – Antenna Unit Connections; Turn off the ANT MOTOR SW on the scanner unit.
  • Page 20 – Confirm that armor is grounded between two flat washers.
  • Page 21 – Fabricating signal cable RW-6895; gasket and flat washers.; Figure 2-5 Fabricating the signal cable RW-6895
  • Page 23 – Figure 2-9 Fabrication of coaxial cable; holes in the scanner chassis. Attach the cover.
  • Page 24 – When the De-Icer is installed; icer turns on when ambient temperature is below 0; Display Unit Connection; ) Cut off jute tape wrapped around the braided
  • Page 25 – Leading in cables to the display unit; Figure 2-12 Location of cable clamp inside the display unit; Tabletop
  • Page 26 – Connections; Power cable; Figure 2-15 Location of GYRO CONVERTER Board; Figure 2-14 Location of filter; Power
  • Page 27 – Grounding; Figure 2-16 Grounding the display unit; Radar buoy; Figure 2-17 INT Board circuit
  • Page 28 – Table 2-1 Input and output signals on the INT Board
  • Page 29 – Figure 2-18 Location of connectors on the INT Board
  • Page 30 – Figure 2-19 Cable clamp
  • Page 31 – Changing Power Specifications; Procedure; ) Unfasten the four screws circled in the
  • Page 32 – Power Supply Unit; Wire the unit as shown in the interconnection diagram.
  • Page 33 – Menus for Initialization and Adjustment; Accessing the menus; ) Press appropriate numeric key to select menu desired.; Menu description and menu tree; INITIAL SETTING 4 menu.
  • Page 34 – Heading Alignment; Figure 3-2 Heading alignment error; INITIAL SETTING 1 menu.; Adjusting Sweep Timing; display as being pulled inward or pushed outward. See Figure 3-3.; Figure 3-3 Examples of correct and
  • Page 35 – Adjusting Video Signal Level; ) Transmit on the 12nm range. Take trigger at TP10 on the same board.
  • Page 36 – Suppressing Main Bang; If main bang appears at the screen center, suppress it as follows.; ) Open the tuning compartment on the control unit.; wise. Note that excessive main bang erases targets in close range.; Figure 3-5 Control unit, location of tuning compartment; Confirming Tuning
  • Page 37 – the tuning indicator lights.; Confirming Magnetron Heater Voltage; ) Turn off the antenna switch in the display unit.
  • Page 50 – Setting method 2: by make and model of gyrocompass
Loading the manual

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - iii; TABLE OF CONTENTS; INITIALIZATION AND ADJUSTMENT

iii TABLE OF CONTENTS EQUIPMENT LISTS ............................................................................ v 1. MOUNTING 1.1 Radiator Assembling Procedure ...................................................................................... 1-11.2 Mounting Structures ..........................

Page 6 - iv; LIST OF INSTALLATION MATERIALS, ACCESSORIES AND SPARE PARTS; OUTLINE DRAWINGS

iv LIST OF INSTALLATION MATERIALS, ACCESSORIES ANDSPARE PARTS LIST OF INSTALLATION MATERIALS, ACCESSORIES AND SPARE PARTS ......................................................... L-1 to L-13 OUTLINE DRAWINGS OUTLINE DRAWINGS .............................................................................

Page 7 - EQUIPMENT LISTS; Complete set

v EQUIPMENT LISTS Complete set . o N e m a N e p y T y t Q s k r a m e R 1 t i n u r e n n a c S F A 6 3 - N S 1 r o t a i d a r a n n e t n A F A 0 3 - N S 6 2 0 0 - B S R 1 t i n u r e n n a c S 1 3 0 0 - B S R 8 8 0 0 - B S R C S H r o f t i n u r e n n a c S 9 8 0 0 - B S R 0 9 0 0 - B S R 2 t i...

Other Furuno Models

All Furuno Other