Furuno DRS6A - Manual

iv EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Radar Sensor XN10A-RSB-118-092 - 1 For DRS4A, w/CP03-32601 XN12A-RSB-118-093 1 For DRS6A, w/CP03-32601 XN12A-RSB-118-094 - 1 For DRS12A, 1255 mm, w/CP03-32601 XN13A-RSB-118-094 1 For DRS12A, 1795 mm, w/CP03-32601 XN12A-RSB-118-095 - 1...

v Optional supply Name Type Code No. Qty Remarks Power Supply Unit PSU-012 - 1 set Gasket OP03-203 001-025-290 1 For DRS2D/4D, φ 10 NMEA2000 cable OP03-205 001-025-790 For DRS4A/6A, φ 10 NMEA2000 cable OP03-206 001-035-290 For DRS25A, φ 10 NMEA2000 cable Resister Assy OP03-204 001-025-300 1 For NMEA...

1 1. MOUNTING 1.1 Mounting Considerations • The radar sensor is generally installed either on top of the wheelhouse or on the radar mast on a suitable platform. Locate the radar sensor where there is a good all-round view. Any obstruc-tion will cause shadow and blind sectors. A mast for instance, wi...

2 For DRS2D/4D 1.2 Mounting Procedure for DRS2D/4D 1. Remove mounting hardware at the bottom of the radar sensor, four each of hex bolts (M10x20), spring washers and flat washers. Save the spring washers and flat washers to use them to fix the radome base to the platform, at step 3. If the thickness...

3 3. Use the hex bolts*, flat washers and spring washers removed at step 1, and fasten the radome base to the platform. The torque should be between 19.6-24.5N z m. *If the thickness of the platform is 6-10 mm, use M10x25 bolts (supplied). For thicker platform, use locally supplied bolts. 4. Mount t...

4 5. Coat the hex bolts (4 pcs.) with silicone sealant. Fasten the antenna radiator to the radiator bracket with the hex bolts, flat washers and spring washers supplied with the radiator. 1.3.2 Mounting the radar sensor The radar sensor can be mounted using the fixing holes on the outside (200 x 200...

5 2. Lay the radar sensor on the mounting platform, orienting it as shown below. (The hinges must face toward the stern.) 3. Insert four hex bolts (M12 x 60, supplied) and seal washers ( φ 30, supplied) from the top of the housing, as shown below. STERN BOW Hinge CAUTION Do not lift the radar sensor...

6 4. Pas s flat washers (M12, supplied), spring washers (M12, supplied) and nuts (M12, supplied) onto hex. bolts. Fasten by tightening nuts. Do not fasten by tightening the hex. bolts; seal washers may be damaged. 5. Coat flat washers, spring washers, nuts and exposed parts of bolts with anticorrosi...

7 Using inside fixing holes of the sensor housing If this radar is replacing a FURUNO radar whose mounting dimensions are the same as this one (140 x 150 mm), it may be possible to use its mounting platform. This method requires removal of the RF unit from the radar sensor to access inside fixing ho...

8 1.4 Mounting of Power Supply Unit PSU-013 (for DRS25A)/PSU-012 (Option) For combinations shown below, the optional power supply unit PSU-012 (Code No.: 000-011-756) is necessary. The PSU-013 is required for any DRS25A installation. *Note: The power supply unit is shipped with 15A fuse. Replace fus...

9 2. WIRING The MFDBB, MFD8, MFD12 or PSU-012 connects to the radar sensor with the two-way cable MOD-ASW0001 (MOD-ASW0002 for DRS25A).In order to minimize the chance of picking up electrical interference, avoid where possible routing the two-way cable near other onboard elec-trical equipment. After...

11 Wiring for DRS25A : Standard Supply : Optional Supply : Local Supply To Multi Function Display BlackBox MFDBB or Multi Function Display MFD8/12 Two-way cable MOD-ASW0002 cable (10/15/20/30 m) 12-24 VDC RADAR SENSOR DRS25A NMEA2000 Equipment NMEA2000 cableM12-05BFFM ( φ 6) or CB-05BFFM ( φ 10) Gro...

12 2.1 Wiring inside DRS2D/4D Two-way cable connection 1. Unfasten three screws at the bottom of the mounting base to remove the fixing plate for the gasket. 2. Remove the gasket, and pass the two-way cable MOD-ASW0001. 3. Fasten the shield of the cable (power) with the cable clamp in the radar sens...

13 6. Slide the gasket on cables so that the amount of cable above the gasket is lower than the RF chassis. Note: If the two-way cable touches the platform near the mounting base, wind vinyl tape around the cable at the point where it is bent. 7. Confirm that the rubber gasket is properly positioned...

14 3. Insert wires of cable M12-05BFFM ( φ 6) or CB-05BFFM ( φ 10) to the NMEA connector inside the radar sensor, consulting the label on the connector for location. As for shield, use the cable clamp shown below to fasten it to the RF chassis. Cable M12-05BFFM ( φ 6) CB-05BFFM ( φ 10) Clamp Use the...

15 4. Push LAN and POWER cables of the two-way cable and cable M12-05BFFM ( φ 6) or CB- 05BFFM ( φ 10) into the slits of the gasket inside the mounting base. Depending on the NMEA2000 cable used, replace the gasket as shown below. Note: The ends of the gasket are different. Larger end should be up) ...

16 2.2 Wiring inside DRS4A/6A/12A/25A Two-way cable connection If you have no NMEA2000 equipment to connect, use the MOD-ASW0001 cable (standard sup-ply). 1. Open the radar sensor cover by loosening four bolts, and fix the stay for safety purpose.2. Unfasten four bolts to detach the plate, gasket, w...

17 5. Attach the LAN cable of the two-way cable to the LAN terminal in the radar sensor. DRS4A/6A/12A DRS25A 6. Refer to the illustration shown below, and attach the gasket to the two-way cable, inserting the cable into the slits on the gasket. Fix the power cable at the foil part with this cable cl...

18 7. Slide the gasket on cables so that the amount of cable above the gasket is lower than the RF chassis. 8. Push the gasket and washers into the hole at the bottom of the radar sensor, then fasten four pan head screws to fix the plate to the sensor. 9. Release the stay and close the cover. Note: ...

19 the crimp-on lug (pre-attached at the bottom of the chassis) to the drain wire, and fasten it with the screw shown below. 5. Depending on the NMEA2000 used, replace the gasket as shown below. DRS4A/6A/12A DRS25A 6. Refer to the illustration shown on next page, and attach the gasket to the two-way...

21 2.4 Wiring inside Power Supply Unit PSU-012 (Option) 1. Detach the body cover by hand.2. Loosen six pan head screws (M3x8) and slide the shield cover upward to remove it.3. Unfasten two pan head screws (M4x12) to remove the cable clamp. 4. Connect the cable VL3P-VV-S2X2C-AA050 (supplied) to the p...

CODE NO. 001‑025‑270‑00 TYPE CP03‑32101 略  図 OUTLINE 名  称  NAME 数量 Q'TY 用途／備考 REMARKS 番 号  NO.  型名／規格 DESCRIPTIONS 1/1 ‑0  INSTALLATION MATERIALS 工事材料表 03HA‑X‑9401 ﾃｲｺｳ組品 RESISTOR ASSEMBLY 120 OHM‑1007#24‑L50 1 000‑167‑746‑10 1 CODE NO. ﾐｶﾞｷ平座金 FLAT WASHER M10 SUS304 4 000‑864‑131‑00 2 CODE NO. M10 ...