Furuno 1935 - Manual

Furuno 1935

Furuno 1935 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
Page: / 48

Table of Contents:

  • Page 3 – SAFETY INSTRUCTIONS; CAUTION; WARNING; Mandatory Action; Read these safety instructions before you operate the equipment.
  • Page 4 – ii; SYSTEM CONFIGURATIONS
  • Page 5 – iii; EQUIPMENT LISTS; Standard supply; Name; Flush Mounting Sponge
  • Page 6 – iv; Optional supply
  • Page 7 – HOW TO INSTALL THE SYSTEM; Display Unit; to a magnetic compass.; How to install the display unit; How to install the display unit on a desktop or the overhead; See the outline drawing on page D-3 for details.
  • Page 9 – Normal position of the antenna unit on the sailboat and powerboat; How to install the antenna unit
  • Page 10 – Wiring and preparation; Remove three shield covers in the radome.
  • Page 13 – or; Radome cover
  • Page 14 – How to install the optional mounting bracket; Mounting bracket kit; How to assemble and install the optional mounting bracket; Type; Hex head bolt
  • Page 15 – How to select the location for the antenna unit; ment. Also do not run the cable in parallel to power cables.
  • Page 16 – Installation procedure; How to fasten the radiator to the radiator bracket; the figure shown below for the location.; Flat washer
  • Page 17 – How to use outside holes of the antenna housing; Location of rubber mat; The radiator may be damaged.
  • Page 19 – How to use the inside holes of the antenna housing; antenna unit. Check the length of bolts before you install.; OR
  • Page 20 – Antenna unit chassis, upper chassis separated
  • Page 21 – How to connect the signal cable; Antenna unit chassis, cover opened
  • Page 24 – This page is intentionally blank.
  • Page 25 – CABLE CONNECTION; Standard Connection; Connect all cables at the rear of the display unit.
  • Page 26 – Data Signal Port
  • Page 27 – HOW TO SET THE EQUIPMENT; How to Set the Language; key to turn on the power.; The window shown below appears.; ENTER
  • Page 28 – How to Set the Purpose; MENU
  • Page 29 – How to Enter the Initial Settings; Basic Settings
  • Page 30 – Heading Adjustment
  • Page 31 – How to automatically set the equipment; The equipment automatically adjusts the tuning, timing and video.; Manual Timing Adjustment; Examples of wrong and correct sweep timings; key to show the setting window.
  • Page 32 – Manual MBS Adjustment; Video Initial Adjustment; Transmit the radar and set the radar as follows.; ARPA Adjustment
  • Page 33 – OPTIONAL EQUIPMENT; Necessary parts; For details, see the packing list attached to the kit.; Remove five connector nuts.
  • Page 34 – Lift the cover slowly and open it as shown below.; Cover
  • Page 36 – Connection of Buzzer and/or Remote Display; External buzzer; cable. Solder the cores, then set the tubes on the soldered point.
Loading the manual

Installation Manual

MARINE RADAR

MODEL1835/MODEL1935/MODEL1945

SAFETY INSTRUCTIONS ............................................................................................................. i

SYSTEM CONFIGURATION ........................................................................................................ ii

EQUIPMENT LISTS .................................................................................................................... iii

1.

HOW TO INSTALL THE SYSTEM..................................................................................... 1-1

1.1

Display Unit ............................................................................................................... 1-1

1.2

Antenna Unit for MODEL1835 .................................................................................. 1-2

1.3

Antenna Unit for MODEL1935/MODEL1945............................................................. 1-9

2. CABLE CONNECTION ......................................................................................................... 2-1

2.1

Standard Connection ................................................................................................ 2-1

2.2

Data Signal Port ........................................................................................................ 2-2

3. HOW TO SET THE EQUIPMENT.......................................................................................... 3-1

3.1

How to Set the Language.......................................................................................... 3-1

3.2

How to Set the Purpose and Model .......................................................................... 3-2

3.3

How to Enter the Initial Settings ................................................................................ 3-3

4. OPTIONAL EQUIPMENT ...................................................................................................... 4-1

4.1

ARP Kit ARP-11 ........................................................................................................ 4-1

4.2

Connection of Buzzer and/or Remote Display .......................................................... 4-4

PACKING LISTS ...................................................................................................................... A-1

OUTLINE DRAWINGS ............................................................................................................. D-1

INTERCONNECTION DIAGRAMS ...........................................................................................S-1

www.furuno.com

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - SAFETY INSTRUCTIONS; CAUTION; WARNING; Mandatory Action; Read these safety instructions before you operate the equipment.

i SAFETY INSTRUCTIONS WARNING Radio FrequencyRadiation Hazard WARNING Standard Steering Display unit 0.45 m 0.30 m CAUTION CAUTION M1835 Antenna unit 0.90 m 0.70 m M1935 Antenna unit M1945 Antenna unit Unit 1.00 m 1.00 m 0.75 m 0.75 m WARNING Indicates a condition that can cause death or serious inj...

Page 4 - ii; SYSTEM CONFIGURATIONS

ii SYSTEM CONFIGURATIONS 12 - 24 VDC Display unit RDP-152 100/110/220/230 VACfor MODEL1835 External buzzer Echo sounderGPS navigatorAIS, etc. Rectifier PR-62 Remote display : Basic configuration Heading sensor MODEL 1835 Antenna unit RSB-0071-057 RSB-0071-057A Echo sounderGPS navigatorAIS, etc. ECON...

Page 5 - iii; EQUIPMENT LISTS; Standard supply; Name; Flush Mounting Sponge

iii EQUIPMENT LISTS Standard supply Note: The name for MODEL1835, MODEL1935, MODEL1945 is shortened to M1835, M1935, M1945 in this manual. Name Type Code No. Qty Comment Display unit RDP-152 - 1 w/Flush mounting sponge 02-160-1201 (1 pc), Self-tapping screw 5x20 SUS304 (4 pcs.) Antenna unit RSB-0071...

Other Furuno Models

All Furuno Other