Fujitsu MB2198-130 - Manual

CONTENTS Chapter 1 Product Overview and Handling Precautions ....................................... 1 1.1 Overview ............................................................................................................................... 21.2 Checking the Items Packaged ..........................

1 Chapter 1 Product Overview and Handling Precautions 1.1 Overview1.2 Checking the Items Packaged1.3 Options1.4 Notes on Use This chapter provides an overview of the adapter and its handling precautions.

2 1.1 Overview ■ Overview The adapter is intended for use in combination with another device such as DSU-FR emulatorheader * 1 to connect a FR-microcontroller based user system to the DSU-FR emulator (MB2198-01 * 2 ). *1 : Hereafter called the header. *2 : Hereafter called the emulator. The major fe...

3 1.2 Checking the Items Packaged ■ Checking the Items Packaged Before using the adapter, make sure that your package contains the following items: • Adapter board: 1 • Flat cables (Standard: 8 cm): 2 • Flat cables (Long: 20 cm): 2 • Hardware manual (This manual in English and a Japanese version): 1...

4 1.3 Options ■ Options Table 1.3-1 Options *1 : The package code of the evaluation MCU is PGA-401C-A02. For the evaluation MCU models available to this adapter and their package codes, Please ask, when unknown. *2 : You need optional items such as debugger software and a communication cable before ...

5 1.4 Notes on Use ■ Handling Precautions • Do not put anything on the adapter. • Before plugging or unplugging any cable, be sure to turn the power supply off. • When unplugging the cable, remove it while holding the case connector without pulling the cable itself. • To prevent electrostatic breakd...

7 Chapter 2 Product Description 2.1 System Configuration2.2 Appearance and Part Names2.3 General Specifications This chapter describes the configuration of the hardware system incorporating the MB2198-130 and showsthe names of its components as well as the major specifications.

8 2.1 System Configuration ■ System Configuration Figure 2.1-1 shows the system configuration for the adapter. * : The AC adapter is bundled with the emulator. Figure 2.1-1 System Configuration Diagram Refer to the emulator hardware manual for connecting the emulator to a host computer or general-pu...

9 2.2 Appearance and Part Names ■ Appearance and Part Names Figure 2.2-1 gives an external view of the adapter board to identify each part of it.The adapter board illustrated in Figure 2.2-1 is in the factory default states. Figure 2.2-1 External View Figure 2.2-1 gives an external view of the adapt...

11 2.3 General Specifications ■ General Specifications Table 2.3-1 lists the general specifications of the adapter. Table 2.3-1 General Specifications * : For the internal power and I/O power supplied to each evaluation MCU, refer to the power sup- ply specifications of the evaluation MCU. For each ...

13 Chapter 3 Functions 3.1 Function Specifications3.2 Connector and IC Socket Specifications This chapter describes the functions of the adapter.

14 3.1 Function Specifications ■ Function Specifications Table 3.1-1 lists the major function specifications of the adapter. Figure 3.1-1 is a block diagram ofexternal-memory emulation. Table 3.1-1 Adapter Function Specifications *1 : The evaluation MCU must support the external-memory emulation fea...

15 3.2 Connector and IC Socket Specifications ■ Connector and Socket Specifications Table 3.2-1 lists the specifications of the connectors and sockets. Table 3.2-1 Connector and IC Socket Specifications The table below lists the specifications of the connectors and sockets on the adapter board. Item...

17 Chapter 4 Connections 4.1 Connecting the Adapter Board to the Emulator4.2 Connecting the Adapter Board with the Header Board4.3 Installing the Evaluation MCU4.4 Installing the Memory Board4.5 Installing a Bypass Capacitor for DVCC Note : Shut off power to the entire system before starting the ope...

18 4.1 Connecting the Adapter Board to the Emulator ■ Connecting the Adapter Board and the Emulator • Connect the adapter board to the emulator in such a manner that their connectors aligned by indexes ( ▲ ) provided to prevent accidental insertion mate deep with each other. • When disconnecting the...

19 4.2 Connecting the Adapter Board with the Header Board ■ Connecting the Adapter Board to the Header Board • To connect the flat cable, insert each of its connectors into the mating connector on each board until the eject lock of the cable’s connector locks into place in the board’s connector. • T...

20 4.3 Installing the Evaluation MCU ■ Installing the Evaluation MCU Open the lever of the evaluation MCU mounting IC socket (SC1) to from the solid-line position tothe dotted-line position. Figure 4.3-1 Installing the Evaluation MCU ■ Mounting Position Align pin No. 1 of the evaluation MCU with its...

22 4.4 Installing the Memory Board ■ Mounting Position Align the dented part of the memory board on the right side with the raised part of the memory boardconnector. Figure 4.4-1 Mounting Position ■ Plugging the Memory Board Push the memory board at a slant into the memory board connector as shown w...

24 4.5 Installing a Bypass Capacitor for DVCC ■ Installing a Bypass Capacitor To use a polarized capacitor such as an electrolytic capacitor as the bypass capacitor, install it ac-cording to the polarity defined by the silk pattern on the PC board. Use meticulous care to check thepolarity.Select the...

25 Chapter 5 Usage 5.1 Setting up the Evaluation MCU Power Supply5.2 Setting the Clock Supply Circuit5.3 Setting Reset Signals5.4 Setting a External Memory Emulation5.5 Power-on/Shutdown Procedures Note : Shut off power to the entire system before starting the operations descried in this chapter. Pe...

26 5.1 Setting up the Evaluation MCU Power Supply ■ Setting up the Evaluation MCU Power Supply Figure 5.1-1 shows the power supply circuit configuration around the evaluation MCU. Figure 5.1-1 Settings of Evaluation MCU Power Supply Setup Jumper Plugs ■ Setting up the Evaluation MCU Power Supply Tab...

28 5.2 Setting the Clock Supply Circuit ■ Installing the Oscillator To supply a clock signal from the adapter board to the main clock (X0/X1) and subclock (X0A/X1A)of the evaluation MCU, install an oscillator and a capacitor on the oscillator IC sockets (SC2 andSC3) on the adapter board, respectivel...

29 ■ Setting the Clock Selector Jumper Plugs Figure 5.2-2 shows the factory settings of the jumper plugs; Table 5.2-1 shows how to set the clockselector jumper plugs. Figure 5.2-3 Setting the Clock Selector Jumper Plugs (Factory Setting) Table 5.2-1 Jumper Plug Settings * : There is no function to s...

30 5.3 Setting a Reset Signal ■ Setting the Reset signal A setup at the time of product shipment of a jumper plug is shown in Fig. 5.3-1. By this setup, theINITX signal (INIT) of evaluation MCU is supplied from the INITX signal of a user system via anemulator, and the TRSTX signal (TRST) of evaluati...

31 5.4 Setting a External Memory Emulation ■ External Memory Emulation Block Diagram Figure 5.4-1 shows the external memory emulation block diagram. Figure 5.4-1 External Memory Emulation Block Diagram ■ Setting the Memory Size Select Switch The memory size select switch select the size of the memor...

32 ■ Setting the Memory Connective Switches These switches can be used to disconnect address lines disabled by the memory capacity switchingfunction from buffers and using them as user resources instead when the external-memory emulationfunction is used. Even when the external-memory emulation funct...

34 Figure 5.5-2 Dialog Display ■ Shutdown Procedure To shut down your system, follow the procedure shown in Figure 5.5-3.To turn off the emulator, press and release the power switch on the back of the emulator. This returnsthe depressed switch to the OFF (raised) state.Check the position of the powe...

35 Chapter 6 Cautions ■ General Cautions on the Adapter • Before setting a jumper plug or switch on the adapter board, turn off all of the adapter, emu- lator, and user system. • The settings of jumper plugs VSEL1 to VSEL4 are related to power supply. Setting these jumper plugs incorrectly can destr...

36 memory board is installed. • The data bus used for external-memory emulation is fixed at 16 bits in width. • Although some of the address bus signals, data bus signals, and control lines of the memory board are connected to the user system, the chip select signal is not connected and thus the use...

37 APPENDIX User Interface Specifications ■ User Interface Specifications Figure A-1 shows the correspondence between the pin numbers of flat cable connectors A and B ofthe adapter board and those of the header or user system. Table A-1 and table A-2 lists the pinoutsof flat cable connectors A and B...

39 Table A-1 Pinouts of Flat Cable Connector A *:The evaluation MCU signal name of table A-1 should keep in mind that actual signal names differ for every kind for a "temporary name". Connector pin number Evaluation MCU signal name (temporary name)* Evaluation MCU pin number Connector pin nu...

40 Table A-2 Pinouts of Flat Cable Connector B *:The evaluation MCU signal name of table A-2 should keep in mind that actual signal names differ for every kind for a "temporary name". Connector pin number Evaluation MCU signal name (temporary name)* Evaluation MCU pin number Connector pin nu...

SS01-71047-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSYEM DSU-FR emulatorPGA-401P adapter Type2MB2198-130Operation Manual January 2005 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.