Fujitsu MB2147-583 - Manual

Page 2 - PREFACE; Handling and use; CAUTION; ) on the NQPACK mounted on the user system with the index mark (; Damage

PREFACE Thank you for purchasing the QFP-100P *1 probe header (MB2147-583) for the F 2 MC *2 -16 family- emulator.The QFP-100P probe header is used to connect the F 2 MC-16L/16LX emulator (MB2147-01 *3 )and the F 2 MC-16L/16LX emulator PGA-299P adapter board (MB2147-20 *4 ) to a user system. That us...

©2005 FUJITSU LIMITED Printed in Japan • The contents of this document are subject to change without notice.Customers are advised to consult with FUJITSU sales representatives before ordering. • The information, such as descriptions of function and application circuit examples, in this document are ...

Page 4 - Checking the Delivered Product; QFP-100P Probe Header; Handling Precautions

1 1. Checking the Delivered Product Before using the QFP-100P probe header, confirm that the following components are included in the box: • QFP-100P Probe Header *1 : 1 • Screws for securing header board (M2 × 10 mm, 0.4 mm pitch) : 4 • Washer : 4 • NQPACK100RB179 *2 : 1 • HQPACK100RB179 *3 : 1 • O...

Page 5 - Notes on Designing; Restrictions of PC board for the user system; Figure 1 Header board dimensions; Approximately

2 3. Notes on Designing ■ Restrictions of PC board for the user system Once the header board is connected to the user system, the heights of parts mounted in the space around the header board are restricted.The PC board of the user system must be designed with due consideration given to this restric...

Page 6 - MCU footprint design notes; ) for the guide pin to fit position when NQPACK is mounted.

3 ■ MCU footprint design notes Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board of the user system. The PC board of the user system must be designed with due consideration given to this footprint as well as to the mass production MCU. For more information, co...

Page 7 - Procedure for Connecting the User System; Connecting; mounted on the user system with the index mark (; TET; Probe cable connector B2

4 4. Procedure for Connecting the User System Before using the QFP-100P probe header, mount the supplied NQPACK on the user system. The header board is used combining the adapter board. To connect the header board to the adapter board, use the flat cable (2 lines) supplied by the emulator sold separ...

Page 8 - Disconnection

5 Figure 4 Header board connection ■ Disconnection To disconnect the header board from the user system, remove all four screws, and then pull the head-er board straight out of the socket Screws for securing header board Washer YQPACK NQPACK Header board User system

Page 9 - Mounting Mass Production MCUs; Mounting; PACK mounted on the user system with the index mark (

6 5. Mounting Mass Production MCUs To mount a mass production MCU on the user system, use the supplied HQPACK (See Figure 5). ■ Mounting 1. To mount a mass production MCU on the user system, match the index mark ( ▲ ) on the NQ- PACK mounted on the user system with the index mark ( ● ) on the mass p...

Page 10 - Connector Pin Assignment; Pin Assignment; *1 : Connected to the main power supply of the evaluation MCU.

7 6. Connector Pin Assignment The signal of Evaluation MCU with which it was carried on the adapter board is connected to YQ-PACK(the same assignments as production MCU) via the probe cable connector(B1,B2) on a header board.An adapter board and a header board are connected to an emulator main part ...

Page 13 - FUJITSU SEMICONDUCTOR; SUPPORT SYSTEM; FUJITSU LIMITED Electronic Devices; Edited

SS01-71045-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM F 2 MC-16 Family EMULATOR QFP-100P PROBE HEADER MB2147-583OPERATION MANUAL May 2005 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.

Fujitsu MB2147-583 - Manual

Table of Contents:

Summary

Other Fujitsu Models