Page 2 - Comments... Suggestions... Corrections...; Copyright and Trademarks
Comments… Suggestions… Corrections… The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs. Feel free to send us your comments by e-mail to [email protected] . Certified documentation ac...
Page 3 - Contents
D2542 (RX100 S5) Technical Manual Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 CE Certificate . . . . . . . . . ....
Page 5 - Introduction; Notational conventions
D2542 (RX100 S5) Technical Manual 5 1 Introduction This technical manual describes the system board D2542, which is equipped with one Intel ® processor. Fur ther information about drivers is provided in the readme files on the hard disk, on the supplied “ServerStar t“ or “Update“ CDs. You will find ...
Page 7 - Important notes; Notes on safety
D2542 (RX100 S5) Technical Manual 7 2 Important notes In this chapter you will find essential information regarding safety when working with your server. V CAUTION! With the system board installed you must open the system to access the system board. How to access the system board of your system is d...
Page 8 - Batteries
8 Technical Manual D2542 (RX100 S5) Notes on safety Important notes V ● Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns!. ● Transmission lines to peripheral devices must be adequately shielded....
Page 10 - Notes about boards; CE Certificate
10 Technical Manual D2542 (RX100 S5) CE Certificate Important notes Notes about boards ● During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. ● Remove the plug from the mains outlet so that system and system board a...
Page 11 - Environmental Protection
D2542 (RX100 S5) Technical Manual 11 Important notes Environmental Protection 2.3 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with standards for ”environmen-tally friendly product design and development“. This means th...
Page 12 - Returning, recycling and disposal
12 Technical Manual D2542 (RX100 S5) Environmental Protection Important notes Returning, recycling and disposal For details on returning and reuse of devices and consumables within Europe, refer to the “Returning used devices” manual, or contact your Fujitsu Siemens Computers branch office/subsidiar...
Page 13 - Features; Overview; Processors
D2542 (RX100 S5) Technical Manual 13 3 Features 3.1 Overview There are two versions of the system board D2542 with the part numbers S26361-D2542-A10 (SAS version) and S26361-D2542-B10 (SATA version). The two versions differ in the chipset and connectors assembling. Processors – One Intel ® Xeon proc...
Page 14 - External connectors
14 Technical Manual D2542 (RX100 S5) Overview Features External connectors – Front side (front panel):2x USB 2.0 port – Rear side (I/O shield):2x USB 2.0 ports1x VGA por t (15 pin)1x keyboard por t1x mouse port1x RS-232-C interface (serial 9 pin2x RJ45 LAN ports (onboard LAN)1x RJ45 service LAN por ...
Page 17 - Main memory; Module population; Basic
D2542 (RX100 S5) Technical Manual 17 Features Main memory 3.2 Main memory The four slots for the main memory are suitable for unbuffered DDR II 800 (PC2-6400) SDRAM memory modules. The organization in two memory banks, 1 and 2, permits rapid memory access with two-way interleaving. I You will find t...
Page 18 - PCI bus; PCI slots
18 Technical Manual D2542 (RX100 S5) PCI bus Features *) Already populated by basic configuration. Install identical DIMMs in socket 1A and 1B and identical DIMMs in socket 2A and 2B. 3.3 PCI bus Figure 3: PCI slots PCI slots The following tables show an overview of the PCI slots: Basic DIMM1A DIMM2...
Page 19 - Screen resolution
D2542 (RX100 S5) Technical Manual 19 Features Screen resolution 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board. If you are using an external screen controller, you will find details of supp...
Page 20 - Temperature / system monitoring; Sensor monitoring
20 Technical Manual D2542 (RX100 S5) Temperature / system monitoring Features Sensor monitoring A fault in a temperature sensor is detected. Should this happen all fans monitored by this sensor run at maximum speed, to achieve the greatest possible protection of the hardware. Voltage monitoring When...
Page 21 - LEDs
D2542 (RX100 S5) Technical Manual 21 Features LEDs 3.6 LEDs Figure 4: LEDs LED s A, B, C, D, E and F are visible from outside on the rear of the server. LED A and LED B are different functionalities of the same LED and are glowing diffe-rently. All the other LEDs are only visible, if the cover of th...
Page 23 - Interfaces and connectors
D2542 (RX100 S5) Technical Manual 23 Features Interfaces and connectors 3.7 Interfaces and connectors Figure 5: Schematic view of the system board D2542 1 = SATA 2 connector (only for SATA version) 11 = SATA 1 connector (only SATA version) 2 = power supply for I 2 C- 12 = System fan 3 3 = power supp...
Page 24 - External ports
24 Technical Manual D2542 (RX100 S5) Interfaces and connectors Features 3.7.1 External ports Figure 6: External ports of the system board D2542 *) The Server Management LAN is a direct communication interface between a remote system and the local iRMC. It is used for “Console Redirection” (text and ...
Page 26 - Settings with jumpers
26 Technical Manual D2542 (RX100 S5) Settings with jumpers Features 3.8 Settings with jumpers The system board is supplied with all jumpers set on the following positions. Figure 8: Jumper default settings JP8 - Boot Block JP5 - Password Skip 1-2 Normal boot (default) 2-3 BIOS recovery 1-2 Disable (...
Page 27 - Replacing the lithium battery
D2542 (RX100 S5) Technical Manual 27 4 Replacing the lithium battery In order to save the system information permanently, a lithium battery is installed to provide the CMOS-memory with a current. When the charge is too low or the battery is empty, a corresponding error message is provided. The lithi...
Page 29 - Abbreviations
D2542 (RX100 S5) Technical Manual 29 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described system board. ACPI Advanced ...
