Fujitsu D1859 - Manual

List of features List of features Onboard features D1859-A Chipset Intel 925 Board size ATX VGAAudio / 8-channel / S/PDIF 5.1 / - / Buzzer / int. Speaker Support - / LAN 1 Gbit / 100 Mbit / 10 Mbit / / LAN ASF / AOL / WOL / Boot / - / / Serial ATA / ATA / RAID / / FireWire TM - USB 2.0 Fan monitorin...

Brief instructions on installing system board Brief instructions on installing system board If you have purchased a separate system board, you can install the system board in your system inaccordance with the following brief instructions.The activities described here assume a basic knowledge of serv...

Brief instructions on installing system board 6 D1859 (Econel 50) ► Should no suitable connection field beprovided in the case, then you mustinstall the connection field (1) provided. Ensure the plate is aligned properly so thatthe connections are suitable for the systemboard later. ► Set the system...

D1859 (Econel 50) 7 Interfaces and connectors P CI 2 P CI 3 P CI 5 PCI 4 PCI Express x1 PCI Express x8 P CI 1 sl ot 1 sl ot 3 sl ot 4 sl ot 2 Channe l B Cha n ne l A 1 23 4 5 6 7 8 16 14 13 12 11 10 9 B IO S S AT A 1 2 3 4 15 B a tte r y 1 CPU fan (F1) 9 Fan connetor (F2) 2 PC98 10 Intrusion 3 Flopp...

External ports 8 D1859 (Econel 50) External ports 1 3 4 5 2 6 7 8 1 PS/2 mouse port 5 VGA port 2 Parallel port/printer 6 Serial interface COM1 3 LAN connector (10/100/1000 Mbit/s) 7 USB1 connector 4 USB0 connector 8 PS/2 keyboard board LAN connector The system board is optionally equipped with the B...

Internal ports and connectors D1859 (Econel 50) 9 Internal ports and connectors The positions of the internal ports and connectors are shown on the Cover. Additional information onsome ports is also provided here. Hard disk connection If you have connected hard disks to serial ATA (one hard disk is ...

Pin assignment of internal ports 10 D1859 (Econel 50) Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Front panel Watch the poling of the LEDs. The positive poleof the connectio...

Pin assignment of internal ports 12 D1859 (Econel 50) USB - dual channel 1 2 11 12 Pin Signal Pin Signal 1 Key 2 Chipcardreader on or not connected 3 VCC 1 or 3 4 VCC 2 or 4 5 Data negative 1 or 3 6 Data negative 2 or 4 7 Data positive 1 or 3 8 Data positive 2 or 4 9 GND 10 GND 11 Key 12 not connect...

Pin assignment of internal ports D1859 (Econel 50) 13 Floppy interface 1 Pin Signal Pin Signal 1 GND 18 Step DIR (low asserted) 2 FDHDIN (low asserted) 19 GND 3 GND 20 Step Pulse (low asserted) 4 not connected 21 GND 5 Key 22 Write Data (low asserted) 6 not connected 23 GND 7 GND 24 Write Enable (lo...

Pin assignment of internal ports 14 D1859 (Econel 50) LCD display 2 1 Pin Signal Pin Signal 1 SMB CLK 8 LAN Link Icon 2 GND 9 Harddisk Action Icon 3 SMB DATA 10 BMC Alert Icon 4 GND 11 Message Icon 5 Key 12 Sleep Icon 6 RFU Reserved for Future use 13 Power Icon 7 LAN Active Icon 14 P3V3P_DUAL Intrus...

Pin assignment of internal ports D1859 (Econel 50) 15 Power supply BTX (ATX compatible) 1 13 Pin Signal Pin Signal 1 +3.3 V (P3V3P) 13 +3.3 V (P3V3P) 2 +3.3 V (P3V3P) 14 -12 V (P12VN) 3 GND 15 GND 4 +5V (VCC) 16 PS on (low asserted) 5 GND 17 GND 6 +5V (VCC) 18 GND 7 GND 19 GND 8 Powergood (high asse...

Pin assignment of internal ports 16 D1859 (Econel 50) Power supply control (System monitoring) 1 Pin Signal 1 Power Guard Control 2 PS FAN Control 4 PS FAN Sense

17 D1859 (Econel 50) Jumper settings The positions of the jumpers are shown on page "Cover". Setting via control-panel plug connector A C 12 12 B 12 Pin pair A inserted =Skipping system and BIOS Setup password Pin pair B inserted = System BIOS recovery Pin pair C inserted = factory setting i...

18 D1859 (Econel 50) Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from themains outlet, before carrying out any of the procedures described in this chapter!Even when you have run down the device, parts of the device (e.g. memory modules, PCIex...

Add-on modules / Upgrading 20 D1859 (Econel 50) Mounting heat sink i Use only the heat sink supplied with your system! Be sure to use heat conducting material between the processor and the heat sink. If a heatconducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwi...

Add-on modules / Upgrading D1859 (Econel 50) 21 Upgrading main memory Technical data Technology: DDR2 400 / DDR2 533 unbuffered DIMM modules184-Pin; 1.8 V; 64 Bit, with ECC Size: 256 Mbytes to 4 Gbytes DDR2 Granularity: 256, 512 or 1024 Mbyte for one socket A current list of the memory modules recom...

Add-on modules / Upgrading D1859 (Econel 50) 23 Adding PCI Express cards The PCI Express x8 slot is intended for graphics cards, and the PCI Express x1 slot forPCI Express x1 cards. Adding PCI cards Technical data:32 bit / 33 MHz PCI slots3.3 V supply voltage (PCI 2.3 compliant)3.3 V auxiliary volta...

Add-on modules / Upgrading D1859 (Econel 50) 25 Replacing the lithium battery In order to permanently save the system information, a lithium battery is installed to provide theCMOS-memory with a current. A corresponding error message notifies the user when the charge istoo low or the battery is empt...

Add-on modules / Upgrading 26 D1859 (Econel 50) BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to newoperating systems, new software or new hardware. In addition, new BIOS functions can also beintegrated.A BIO...

Add-on modules / Upgrading D1859 (Econel 50) 27 BIOS Recovery - Recovering System BIOS i All BIOS settings are reset to the default values. ► Open the casing as described in the operating manual. ► On the system board set the jumper to the appropriate setting to restore the system BIOS (see chapter ...

Add-on modules / Upgrading 28 D1859 (Econel 50) Microcode Update What is a microcode update? As there are no drivers for processors, Intel offers the possibility from the P6 family (Pentium Pro) onto update the command set (microcode) of the processor. This enables minor errors to be correctedand th...

Annex D1859 (Econel 50) 29 Annex System board Revision and BIOS Version System board Revision The revision status of the system board exactly identifies which system board you have. It isindicated on a sticker on the edge of the system board: D1859-A10 GS 1 05618476 Example System board r evision BI...

Annex 30 D1859 (Econel 50) Electrical Properties Loadability for connections and fuses i Make sure that the connected devices do not overload the connections. Fuse no. Fuse Connection Maximum loadability 1 750 mA Keyboard Not specified Mouse Not specified 2 2000 mA USB port 1 500 mA USB port 2 500 m...

Error messages D1859 (Econel 50) 31 Error messages This chapter contains error messages generated by the system board. Available CPUs do not support the same bus frequency - System halted! Memory type mixing detected Non Fujitsu Siemens Memory Module detected - Warranty void There are more than 32 R...

35 D1859 (Econel 50) Glossary The technical terms and abbreviations given below represent only a selection of the full list ofcommon technical terms and abbreviations.Not all technical terms and abbreviations listed here are valid for the described system board. AC'97 Audio Codec '97 ACPI Advanced C...

Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu-ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So-lutions. This document from the document archive refers to a product version which was released a considerable time ago or...