Fujitsu D1382 - Manual

Features A26361-D1382-Z120-1-7419 English - 3 Features The components and connectors marked are not necessarily present on the system board. · System board in µATX format · Intel processor Pentium 4 from 1.4 GHz and with 400 /533 MHz Front Side Bus. Pentium 4 processors support MMX technology and In...

Features 4 - English A26361-D1382-Z120-1-7419 · 1 AGP slotThe AGP slot supports 4x AGP mode. Only AGP boards with 1.5 V are supported. · IDE hard disk controller connected to PCI bus for up to four IDE drives(e.g. IDE hard disk drives, ATAPI CD-ROM drives)The IDE hard disk controller are ATA100, ult...

Features A26361-D1382-Z120-1-7419 English - 5 Internal ports and connectors DIMM 2 DIMM 1 PC I 1 PC I 2 PC I 3 AG P 14 15 1 2 3 4 5 6 8 7 13 10 12 9 11 17 16 13 1 = Power supply ATX 2 = Floppy Disk Drive 3 = IDE drives 3 and 4 (secondary) 4 = Power supply monitoring 5 = Connector for front panel 6 =...

Features 6 - English A26361-D1382-Z120-1-7419 Temperature / System monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damagecaused by overheating. In addition, any unnecessary noise is also prevented by reducing the fanspeed, and information is provide...

Features A26361-D1382-Z120-1-7419 English - 7 Voltage monitoring: The voltages 12 V, 5 V and the CMOS battery are monitored. With hardware monitoring - regardless of the operating system and processor - the advantagescompared to conventional software monitoring are clear: - suitable for all operatin...

Features 8 - English A26361-D1382-Z120-1-7419 Screen resolution Depending on the operating system used, the screen resolutions in the following table refer to thesystem board screen controller. If you are using an external screen controller, you will find details of supported screen resolutions inth...

Settings with switches and jumpers A26361-D1382-Z120-1-7419 English - 9 Settings with switches and jumpers 1 2 3 4 ON Switch 1 = must always be set to off Switch 2 = System BIOS recoverySwitch 3 = must always be set to off Switch 4 = must always be set to off i The clock frequency of the processor i...

Add-on modules A26361-D1382-Z120-1-7419 English - 11 Installing and removing processors 3 2 1 A 4 5 3 2 1 A 4 5 Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Ê Remove the old processor from the socket (3). Ê Insert the new processor in the socket so that th...

Add-on modules 12 - English A26361-D1382-Z120-1-7419 Upgrading main memory These slots are suitable for 128, 256, 512 and 1024 Mbyte DDR memory modules of the DIMMformat. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2,5 V memory modules. Buffered mem...

Add-on modules A26361-D1382-Z120-1-7419 English - 13 Replacing the lithium battery ! Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery typerecommended by the manufacturer (CR2032). Do not throw li...

Glossary 14 - English A26361-D1382-Z120-1-7419 Glossary The technical terms and abbreviations given below represent only a selection of the full list ofcommon technical terms and abbreviations.Not all technical terms and abbreviations listed here are valid for the described system board. ACPI Advanc...