Page 5 - Operating Manual
CELSIUS M / V / R Operating Manual Introduction Important notes Preparing for use Operation Troubleshooting and tips System expansions Technical data Index Edition: November 2007
Page 7 - Contents
A26361-K990-Z120-1-7619, Edition 6 Contents Your CELSIUS... .................................................................................................................................. 1 Notational conventions .......................................................................................
Page 10 - Notational conventions
Your CELSIUS... 2 A26361-K990-Z120-1-7619, Edition 6 Notational conventions The following symbols are used in this manual: ! indicates information which is important for your health or for preventing physical damage. i indicates important information which is required to use the system properly. ► T...
Page 11 - Important notes; Safety notes
A26361-K990-Z120-1-7619, Edition 6 3 Important notes In this chapter you will find information regarding safety which it is essential to take note of when working with your device. Safety notes ! Pay attention to the information provided in the "Safety" manual and in the following safety not...
Page 12 - Energy saving, disposal and recycling
Important notes 4 A26361-K990-Z120-1-7619, Edition 6 Energy saving, disposal and recycling Further information can be found on the "User Documentation" or "Drivers & Utilities" DVD provided with your computer. CE mark CE mark for devices without radio component The shipped versio...
Page 13 - FCC Class B Compliance Statement
Important notes A26361-K990-Z120-1-7619, Edition 6 5 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. NOTE: This equipment has be...
Page 15 - Preparing for use; Unpacking and checking the delivery; Steps for initial setup
A26361-K990-Z120-1-7619, Edition 6 7 Preparing for use ! Please observe the safety information in the "Important notes" chapter. Unpacking and checking the delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date. ► Un...
Page 16 - Setting up the device
Preparing for use 8 A26361-K990-Z120-1-7619, Edition 6 Setting up the device ! When installing your device, give consideration to the safety notes in the "Safety" manual. The device should only be set up in the intended orientation, i.e. in a vertical position. We recommend that you place yo...
Page 17 - Connect the monitor, mouse and keyboard; Connecting monitor
Preparing for use A26361-K990-Z120-1-7619, Edition 6 9 Unscrewing the base foot (CELSIUS V, CELSIUS R6xx) 1 1 2 ► Unscrew the knurled screws (1). ► Pull off the base foot in the direction of the arrow (2). Connect the monitor, mouse and keyboard The ports for the monitor, mouse, and keyboard are on ...
Page 18 - Connecting the mouse; Keyboard, connecting
Preparing for use 10 A26361-K990-Z120-1-7619, Edition 6 Connecting the mouse Depending on the equipment level selected, your device will be supplied with a PS/2 mouse or a USB mouse. PS/2 mouse: connecting ► Connect the PS/2 mouse to the PS/2 mouse port of the device. Connecting USB mouse ► Connect ...
Page 19 - Connecting the device to the mains voltage
Preparing for use A26361-K990-Z120-1-7619, Edition 6 11 Connecting the device to the mains voltage i The device is fitted with a wide voltage range power supply. This means you do not need to set the nominal voltage manually for these devices. Therefore there is no switch available for the voltage s...
Page 20 - Switching on for the first time: installing the software; Switching on monitor and device
Preparing for use 12 A26361-K990-Z120-1-7619, Edition 6 Switching on for the first time: installing the software If the device is integrated into a network, the user and server details as well as the network protocol are required during the software installation. Contact your network administrator i...
Page 21 - Installing the software; External devices, connecting
Preparing for use A26361-K990-Z120-1-7619, Edition 6 13 Installing the software ► During installation, follow the instructions on screen. ► Consult the operating system manual if there is anything unclear about the requested input data. i You will find further information about the system, drivers, ...
Page 22 - Ports provided by the device; LAN
Preparing for use 14 A26361-K990-Z120-1-7619, Edition 6 Ports provided by the device The connections are located on the front and back of the device. The ports available on your device depend on the configuration level you have selected. The standard ports are marked with the symbols shown below (or...
Page 23 - Connecting external devices to the parallel or serial port
Preparing for use A26361-K990-Z120-1-7619, Edition 6 15 Connecting external devices to the parallel or serial port External devices can be connected to the parallel or serial port (e.g. a printer or a modem). ► Connect the data cable to the external device. ► Depending on the device, connect the dat...
Page 24 - Connecting external devices to the FireWire port
Preparing for use 16 A26361-K990-Z120-1-7619, Edition 6 Connecting external devices to the FireWire port External devices such as digital audio/video devices or other high-speed devices can be connected to the FireWire port. The FireWire port operates at a speed of up to 400 Mbit per second. i FireW...
Page 25 - Operation; Switching the device on; Switching off the device
A26361-K990-Z120-1-7619, Edition 6 17 Operation Switching the device on ► If necessary, switch the monitor on (see the operating manual for the monitor). ► Press the ON/OFF switch on the front of the device. The power-on indicator lights green and the device is started. Switching off the device ► Sh...
Page 26 - Indicators provided by the device
Operation 18 A26361-K990-Z120-1-7619, Edition 6 Indicators provided by the device The indicators are on the front of the casing. Which indicators are available on your device depends on the configuration level you have selected. 1 2 3 4 5 1 = Hard disk indicator 2 = Power-on indicator 3 = Drive indi...
Page 27 - Keyboard; Important keys and key combinations
Operation A26361-K990-Z120-1-7619, Edition 6 19 Drive indicator, e.g. DVD The indicator lights up when the CD-ROM or DVD drive is accessed. You may only remove the DVD when the indicator is dark. Floppy disk indicator (optional) The indicator lights up when the floppy disk drive of the device is acc...
Page 29 - Working with floppy disks
Operation A26361-K990-Z120-1-7619, Edition 6 21 Working with floppy disks i Follow the instructions supplied by the vendor of the floppy disks. Do not clean the floppy disk drive with cleaning floppy disks. Any attempt would destroy the read/write head in the disk drive within 20 seconds. 3 2 1 5 6 ...
Page 30 - Settings in BIOS Setup; Property and data protection
Operation 22 A26361-K990-Z120-1-7619, Edition 6 Settings in BIOS Setup In BIOS Setup you can set the system functions and the hardware configuration of the device. When the PC is delivered, the default entries are valid (see "BIOS Setup" manual or manual for the mainboard). You can customise...
Page 31 - BIOS setup security functions
Operation A26361-K990-Z120-1-7619, Edition 6 23 BIOS setup security functions The Security menu in BIOS Setup offers you various options for protecting your personal data against unauthorised access, e.g.: ● Preventing unauthorised access to the BIOS Setup. ● Preventing unauthorised system access ● ...
Page 33 - Troubleshooting and tips
A26361-K990-Z120-1-7619, Edition 6 25 Troubleshooting and tips ! Refer to the safety notes in the "Safety" manual and in the "Preparing for use" chapter when connecting or disconnecting cables. If a fault occurs, try to correct it as described in the following places: ● in this chapt...
Page 34 - Troubleshooting; The device cannot be switched off with the ON/OFF switch
Troubleshooting and tips 26 A26361-K990-Z120-1-7619, Edition 6 Troubleshooting Power-on indicator remains unlit after you have switched on your device Cause Troubleshooting The mains voltage supply is faulty. ► Check whether the power cable is plugged properly into the device and a grounded mains ou...
Page 36 - No mouse pointer displayed on the screen
Troubleshooting and tips 28 A26361-K990-Z120-1-7619, Edition 6 Cause Troubleshooting Wrong setting for the monitor under Windows Vista ► Restart the device. ► Press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears. ...
Page 37 - The floppy disk cannot be read or written; Time and/or date is not correct; Error messages on the screen; Installing new software
Troubleshooting and tips A26361-K990-Z120-1-7619, Edition 6 29 The floppy disk cannot be read or written Cause Troubleshooting The write protection of the floppy disk or the floppy disk drive is activated. ► Check that the write protection of the floppy disk or the floppy disk drive is activated (re...
Page 38 - Hard disk contents, restoring
Troubleshooting and tips 30 A26361-K990-Z120-1-7619, Edition 6 Hard disk contents, restoring Should you need to restore your hard disk, the instructions are provided on the case of the "Recovery-CD/DVD" (delivered with your system). Tips Topic Tip Out of system resources If you have too many...
Page 39 - System upgrades; Information about boards
A26361-K990-Z120-1-7619, Edition 6 31 System upgrades i As the device has to be shut down in order to install/deinstall system hardware components, it is a good idea to print out the relevant sections of this chapter. It may be necessary to update the BIOS when carrying out a system expansion or har...
Page 40 - Opening the casing
System upgrades 32 A26361-K990-Z120-1-7619, Edition 6 Opening the casing ► Switch the device off. The device must not be in the energy-saving mode! ! Please take note of the safety information in the "Important notes" chapter. Pull the power plug out of the mains outlet. Only insert the powe...
Page 42 - Closing the casing
System upgrades 34 A26361-K990-Z120-1-7619, Edition 6 Closing the casing Variant A (version with knurled screws) a ► Hook the side cover into the upper and lower guide rail of the casing in the direction of the arrow (1). Make sure that the side cover is offset by approximately 2 cm (a). ► Press the...
Page 44 - Opening front panel
System upgrades 36 A26361-K990-Z120-1-7619, Edition 6 Opening front panel ► Open the casing (see "Opening the casing"). 1 1 1 2 ► Detach the three locking tabs on the left side of the front panel (1). ► Fold open the front in the direction of the arrow (2). ► If necessary, detach the hinge o...
Page 45 - Closing front panel
System upgrades A26361-K990-Z120-1-7619, Edition 6 37 Closing front panel 1 2 2 2 ► If necessary, hook in the hinge on the right-hand side of the front panel. ► Close the front panel in the direction of the arrow (1) so that the three locking tabs on the left-hand side of the front panel engage (2)....
Page 46 - Removing the side fan
System upgrades 38 A26361-K990-Z120-1-7619, Edition 6 Removing the side fan You will need to remove the side fan inside the casing in order to install boards or upgrade the main memory. 1 2 a ► Open the casing (see "Opening the casing"). ► Release the side fan by pressing the locking hook (a...
Page 47 - Installing the side fan
System upgrades A26361-K990-Z120-1-7619, Edition 6 39 Installing the side fan 2 1 1 a ► Connect the fan cable to the corresponding plug contact on the mainboard (refer also to the manual of the mainboard). ► Position the side fan at a slight angle in the direction of the arrow (1) and hook the fan l...
Page 56 - Removing the ventilation duct (CELSIUS R5xx)
System upgrades 48 A26361-K990-Z120-1-7619, Edition 6 Removing the ventilation duct (CELSIUS R5xx) Before you can upgrade the main memory or the processor, or before you can replace the processor or the lithium battery, you must remove the ventilation duct. 1 1 2 ► Release the ventilation duct by pr...
Page 57 - Installing the ventilation duct (CELSIUS R5xx)
System upgrades A26361-K990-Z120-1-7619, Edition 6 49 Installing the ventilation duct (CELSIUS R5xx) i When routing the fan cable, make sure that it is not kinked or pinched. When fitting the ventilation duct, be careful not to damage the processor cooler(s) on the mainboard. 1 ► Slide the ventilati...
Page 58 - Removing the cross-piece
System upgrades 50 A26361-K990-Z120-1-7619, Edition 6 Removing the cross-piece To upgrade the main memory or replace the processor you will need to remove the cross-piece. b a 1 2 b ► Remove the ventilation duct (see "Removing ventilation duct (CELSIUS V)" or "Removing the ventilation du...
Page 59 - Installing the cross-piece
System upgrades A26361-K990-Z120-1-7619, Edition 6 51 Installing the cross-piece 1 2 2 c b a a ► Insert the cross-piece into its brackets (a) on the rear of the casing at a slight angle. Make sure that the plexiglass plate of the cross-piece is not trapped between the memory slots. ► Press the cross...
Page 60 - Removing cover of power supply (CELSIUS M)
System upgrades 52 A26361-K990-Z120-1-7619, Edition 6 Removing cover of power supply (CELSIUS M) On the CELSIUS M the connector P11 is located behind the cover of the power supply. When changing the hard disk equipment, you must remove the cover. 2 1 3 ► Unscrew the knurled screw (1). ► Pull the cov...
Page 61 - Installing cover of power supply (CELSIUS M)
System upgrades A26361-K990-Z120-1-7619, Edition 6 53 Installing cover of power supply (CELSIUS M) 2 1 3 ► Insert the cover into the casing in the direction of the arrow (1). ► Slide the cover in the direction of the arrow as far as it will go (2). ► Fasten the cover with the knurled screw (3).
Page 62 - Installing and removing a board; Installing a board
System upgrades 54 A26361-K990-Z120-1-7619, Edition 6 Installing and removing a board ! Please take note of the section "Information about boards". The number, position and arrangement of the board slots on the mainboard can be found in the manual for the mainboard. Boards may already be ins...
Page 64 - Removing a board
System upgrades 56 A26361-K990-Z120-1-7619, Edition 6 Removing a board ► Open the casing (see "Opening the casing"). ► Remove the fan (see "Removing the side fan"). ► Remove the cross-piece if it is in the way (see "Removing the cross-piece”). ► Disconnect the cables connected to...
Page 67 - Installing and removing drives
System upgrades A26361-K990-Z120-1-7619, Edition 6 59 Installing and removing drives The casing can accommodate a total of seven drives: ● three accessible drives (two 5¼" drives and one 3½" drive) ● four non-accessible drives (3½" drives) "Accessible drives" are e.g. DVD or CD R...
Page 69 - Removing an accessible drive
System upgrades A26361-K990-Z120-1-7619, Edition 6 61 Removing an accessible drive ► Open the casing (see "Opening the casing"). 1 1 3 2 ► Pull the data and the power supply connectors from the desired drive. ► Loosen the screws (1). ► Slide the drive out of the bay in the direction of the a...
Page 71 - Installing an accessible drive
System upgrades A26361-K990-Z120-1-7619, Edition 6 63 Installing an accessible drive ► Open the casing (see "Opening the casing"). ► If a slide-in module is fitted, remove this first. To do this, proceed in the same way as when removing an accessible drive (see "Removing an accessible dr...
Page 72 - Floppy disk drive - removing and installing
System upgrades 64 A26361-K990-Z120-1-7619, Edition 6 Floppy disk drive - removing and installing Removing the floppy disk drive ► Remove the floppy disk drive (see "Removing an accessible drive"). 1 1 2 2 ► Remove the screws (1) on both sides of the slide-in module. ► Pull the disk drive ou...
Page 73 - Installing and removing the hard disk drive; Installing a hard disk drive
System upgrades A26361-K990-Z120-1-7619, Edition 6 65 Installing and removing the hard disk drive Installing a hard disk drive ► Open the casing (see "Opening the casing"). ► Take the new hard disk drive out of its packaging. ► Only for SCSI drives: Make the required settings on the drive. a...
Page 74 - Removing a hard disk drive
System upgrades 66 A26361-K990-Z120-1-7619, Edition 6 ► CELSIUS M only: Remove the cover of the power supply (see "Removing cover of power supply (CELSIUS M) "). ► Connect the data and power supply cables to the hard disk drive or to the hard disk drives. ► CELSIUS M with SCSI hard disk only...
Page 76 - SmartCard reader, installing
System upgrades 68 A26361-K990-Z120-1-7619, Edition 6 Installing/removing a SmartCard reader (optional) You can also install a SmartCard reader in the bay of the floppy disk drive in place of the drive. i You can install either a WLAN module or a SmartCard reader in your device. SmartCard reader, in...
Page 78 - Removing a SmartCard reader
System upgrades 70 A26361-K990-Z120-1-7619, Edition 6 Removing a SmartCard reader ► Remove the insert with the SmartCard reader (see "Removing an accessible drive"). 2 1 1 ► Detach the locking mechanisms (1) and remove the bezel (2). 1 1 2 2 ► Remove the screws on both sides of the slide-in ...
Page 80 - Installing and removing a WLAN module (optional); Installing WLAN module
System upgrades 72 A26361-K990-Z120-1-7619, Edition 6 Installing and removing a WLAN module (optional) i You can install either a WLAN module or a SmartCard reader in your device. Installing WLAN module ► Open the casing (see "Opening the casing"). ► Open the front panel (see "Opening fr...
Page 83 - Removing WLAN module
System upgrades A26361-K990-Z120-1-7619, Edition 6 75 Removing WLAN module ► Open the casing (see "Opening the casing"). ► Open the front panel (see "Opening front panel"). ► Detach the USB data cable of the WLAN module from the mainboard (see the manual for the mainboard). 2 1 1 ► L...
Page 84 - Extensions to the mainboard; Main memory, upgrading
System upgrades 76 A26361-K990-Z120-1-7619, Edition 6 Extensions to the mainboard Details on how you can upgrade the main memory or the processor of your device are provided in the manual for the mainboard. Main memory, upgrading ► Open the casing (see "Opening the casing"). ► CELSIUS V/R on...
Page 87 - Technical data
A26361-K990-Z120-1-7619, Edition 6 79 Technical data Electrical data Regulations complied with: EN 60950 UL 60950 CSA 22.2 No.950 Protection class: I Rated voltage range: 100 V - 240 V Rated frequency: 50 Hz - 60 Hz Max. rated current (CELSIUS M): 100 V – 127 V : 6 A 200 V – 240 V : 3 A Max. rated c...
Page 89 - Index
A26361-K990-Z120-1-7619, Edition 6 81 Index 3 3 1/2-inch drive 60 5 5 1/4-inch drive 60 A Access permission, SmartCard 23 Accessible drive installing 64 removing 62 Alphanumeric keypad 19 Anti-theft protection 22 ATA drive, serial 60 Audio devices, connecting 16 Audio input 14 Audio output 14 B Base...