Fujitsu AOU36T - Manual

En- 7 PREPARATION CAUTION! ● Take care to prevent infants from acciden-tally swallowing batteries. ● When not using the remote control unitfor an extended period, remove the bat-teries to avoid possible leakage and dam-age to the unit. ● If leaking battery fluid comes in contactwith your skin, eyes,...

En- 9 Example: When set to COOL Example: When set to 80 °F To Select Mode Operation 1 Press the START/STOP button (Fig.6 P ). The indoor unit’s OPERATION indicator lamp (red) (Fig. 3 5 ) will light. The air conditioner will start operation. 2 Press the MASTER CONTROL button (Fig.6 K ) to se- lect th...

En- 10 To Select Automatic Operation Press the MASTER CONTROL button to select AUTO. The operating mode “AUTO” will appear alone in the display. The transmit indi-cator will flash to indicate the command has been sent, and about three sec-onds later the entire display panel will reappear. To Set the...

En- 11 To Select Mode Operation 1 Press the START/STOP button. The indoor unit’s OPERATION indicator light (red) will be on.The air conditioner will start operating. 2 Press the MASTER CONTROL button to select the de-sired mode. Each time the button is pressed, the mode will change in the followingo...

En- 13 TIMER OPERATION SLEEP TIMER SET TIME SET TEMP MASTER CONTROL FAN CONTROL . TIMER ON SLEEP TIMER SET TIME SET TEMP MASTER CONTROL FAN CONTROL . TIMER ON Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Before using the timer function, be sure...

En- 14 TIMER OPERATION SLEEP TIMER OPERATION Set time 1 hour 2 ° F 4 ° F SLEEP TIMER SET TIME SET TEMP MASTER CONTROL FAN CONTROL . SLEEP COOL About the PROGRAM timer ● The PROGRAM timer allows you to integrate OFF timerand ON timer operations in a single sequence. The se-quence can involve one tran...

En-1 5 ADJUSTING THE DIRECTION OF AIR CIRCULATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). Vertical (up-down) direction of airflow is adjusted by pressing the remote control unit’s AIR FLOW DIRECTION VERTICAL SETbutton. Horizontal (right-le...

En-1 6 ADJUSTING THE DIRECTION OF AIR CIRCULATION Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit’s AIR FLOW DIRECTION button. Hori-zontal (right-left) airflow direction is adjusted manually, by moving the Air Flow Direction Louvers.Whenever making horizontal ...

En-1 7 SWING OPERATION Begin air conditioner operation before performing this procedure. About Swing Operation ● The SWING range is as follows: ● The SWING operation may stop temporarily when the airconditioner’s fan is not operating or when operating atvery low speeds. ● The airflow direction can n...

En-1 9 ENERGY SAVE OPERATION Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). The air conditioner can be operated while keeping energy consumption costs down. How To Use the ENERGY SAVE OPERATION 1 Press the START/STOP button(if the unit is already...

En- 20 ● Before cleaning the air conditioner, be sure to turn it off and disconnect the power supply. ● Be sure the intake grille is installed securely. ● When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-sonal injury may result. ● Turn off the circuit brea...

En- 22 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “HEAT & COOL MODEL” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the cir-cuit breaker, and consult authorized service personnel.Merely turning off the ...

En- 24 OPERATING TIPS Indoor temperature Outdoor temperature Indoor humidity Cooling and Dry Mode 95 °F DB / 71 °F WB 64 °F DB / 55 °F WB 115 °F DB 32 °F DB About 80 % or less If the unit is used for long periods under high-humidity conditions, condensationmay form on the surface of the indoor unit,...