Fujitsu 620C - Manual - manualsarea.com

Page 2 - ii; FCC Radio Frequency Interference Statement; * Consult the dealer or an experienced radio/TV technician for help.

ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digitaldevice, pursuant to Part 15 of the FCC rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Th...

Page 3 - iii; Table of Contents; INDEX

iii Table of Contents 1. INTRODUCTION ........................................................................................... 1-1 2. INSTALLATION ............................................................................................ 2-1 2.1 SHIPPING BRACKET ...................................

Page 4 - Figure 1-1 Scanner packing

1-1 1. INTRODUCTION Congratulations on your purchase of Fujitsu ScanPartner 620C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through thismanual. It provides you with the proper instructions on how to unpack, install, operate andmaintain the Scanner. Fig...

Page 5 - If any items; Precautions; Do not install the Scanner in a humid or dusty place.

2-1 2. INSTALLATION Please unpack the Scanner carefully, and check the contents against the c hecklist. If any items are missing or damaged, please contact your authorized local dealer immediately. Precautions • Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat ma...

Page 7 - vii). Carefully place the Scanner back into its normal position.; SCSI INTERFACE DEVICE ID

2-3 2.1.2 REFITTING THE SHIPPING BRACKET Whenever you need to move the Scanner to a new location it is advisable to refit the shippingbracket to avoid causing damage to the Scanners’ internal mechanism. Please follow theinstructions below to refit the shipping bracket. i). Turn off the Scanner power...

Page 17 - CLEANING THE GLASS; area and ADF area by moving the swab from side to side.

3-3 3.2 CLEANING THE GLASS The procedures: i). Soak a cotton swab with some isoprophy alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii). Close the ADF unit and document cover. Your S...

Page 18 - Disassembling Procedure

3-4 3.3 REPLACING THE ADF SNAP-IN PAD MODULE After scanning approximately 150,000 pages through the ADF, the pad spring may be worn outand you may experience problems with document feeding. In this case, it is highly recommendedto replace the pad module with a new one. For ordering the pad module, p...

Page 19 - Assembling Procedure; Take out the ADF pad module from the box.

3-5 Assembling Procedure 1. Take out the ADF pad module from the box. 2. Hold the upper part of the pad clamp and place it gently to the pad holder as shown in Figure 3-4. Figure 3-4 Installing the pad module ADF PadModule Upper Part of the PadClamp

Page 20 - QUESTION AND ANSWER; “Fujitsu Driver Kit” to check this out.

4-1 4. TROUBLESHOOTING The Scanner will automatically perform a simple self-test each time it is turned on. This will help spot major system errors in the Scanner itself. When the test is initiated, the READY LED is flashing. When the test is completed, if no error occur, the READY LED is steadily o...

Page 22 - PAPER JAM IN THE ADF

4-3 Question: While scanning, the Scanner often makes noises, or it scans back and forth. Answer: Please choose lower speed from the TWAIN user interface for low speed PC. Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 ...

Page 24 - Paper with clip or staple attached

5-1 5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: • Paper with clip or staple attached; • Paper with ink not totally dry; • Paper with inconsistent thickness, such as envelopes; • Paper with wrinkles, curls, folds or tears; •...

Page 25 - SCANPARTNER 620C SPECIFICATIONS

5-2 5.1 SCANPARTNER 620C SPECIFICATIONS Scanner Type v 1-pass colour v Flatbed with ADF built-in Scanning Mode v 36-bit colour v 12-bit Grey Scale v Line Art/Halftone v Error Diffusion (single bit) Optical Resolution v 600 x 1200 dpi in a dpi increments Light Source v Cold Cathode fluorescent lamp A...

Page 26 - Index; SCSI Termination

a Index A ADF cover · 4-3 ADF Scanning · 2-8 B balance wire · 2-8 C Cleaning the ADF · 3-1 Cleaning the Glass · 3-3 Connecting the Cable · 2-9 D document cover · 2-5 Document Loading · 2-7 O output paper tray · 2-6 output paper tray extension · 2-6 P paper chute · 2-5 paper chute extension · 2-5 pap...

Fujitsu 620C - Manual

Table of Contents:

Summary

Other Fujitsu Models