Fujitsu 15C - Manual - manualsarea.com

Page 2 - Table of Contents

ii Table of Contents 1. INTRODUCTION .......................................................................................... 1-1 2. INSTALLATION AND CONNECTIONS .................................................. 2-1 2.1 S HIPPING B RACKET .............................................................

Page 3 - INTRODUCTION; Figure 1-1 shows how the Scanner is packed. You can check all items

1-1 1. INTRODUCTION Congratulations on your purchase of Fujitsu Scanpartner 15C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner. Fi...

Page 4 - Figure 1-1 Scanner packing

Page 5 - INSTALLATION AND CONNECTIONS; Precautions; Do not install the Scanner in a humid or dusty place.; Shipping Bracket; Carefully place the Scanner in an upright position on its front.

2-1 2. INSTALLATION AND CONNECTIONS Please unpack the Scanner carefully, and check the contents against the checklist. Ifany items are missing or damaged, please contact your authorized local dealerimmediately. Precautions ❖ Keep the Scanner out of direct sunlight. Direct exposure to the sun or exce...

Page 7 - Refitting the Shipping Bracket:; Turn off the Scanner power at the power on/off switch.; SCSI Interface Device ID

2-3 2.1.2 Refitting the Shipping Bracket: Whenever you need to move the Scanner to a new location it is advisable torefit the shipping bracket to avoid causing damage to the Scanners’ internalmechanism. Please follow the instructions below to refit the shipping bracket. i). Turn off the Scanner powe...

Page 8 - Figure 2-3 Adjusting the SCSI ID setting.

2-4 Figure 2-3 Adjusting the SCSI ID setting. SCSI ID Selector

Page 10 - Figure 2-5 Install the ADF Output Paper Tray

2-6 2.4 ADF Output Tray (Figure 2-5) i). Hold the output paper rack some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the output paper tray to the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF. iv). Pul...

Page 11 - Document Loading; For flatbed scanning.

2-7 2.5 Document Loading For flatbed scanning. Documents that can not be scanned using the ADF can be placed on the flatbed forscanning. Refer to Figure 2-6) i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned w...

Page 12 - ADF Scanning; Figure 2-7 - Use ADF to Load Multiple Documents

2-8 2.6 ADF Scanning Standard paper size can be scanned automatically using the ADF. Refer to figure 2-7. i). To prevent occasional paper jam when automatically feeding multipledocuments, fan the paper before loading. ii). Lift the balance wire and place the documents to be scanned onto the ADF pape...

Page 14 - Figure 2-8 Scanpartner 15C Scanner Cable Connection; SCSI Cable

2-10 Figure 2-8 Scanpartner 15C Scanner Cable Connection Figure 2-9 Scanpartner 15C SCSI Scanner Cable Connections with Mac SCSI Cable

Page 15 - MAINTENANCE; Cleaning the ADF

3-1 3. MAINTENANCE 3.1 Cleaning the ADF Your Scanner is designed to be maintenance free. However, it still needs tobe cleaned occasionally to ensure optimum image quality and performance. From time to time the pad assembly and feeding rollers may becomecontaminated with ink, toner particles or paper...

Page 16 - Figure 3-1 Opening the ADF unit and Document Cover

3-2 Figure 3-1 Opening the ADF unit and Document Cover

Page 17 - Cleaning the Glass; Figure 3-2 The Cleaning Area

3-3 3.2 Cleaning the Glass The procedures: i). Soak a cotton swab with some isoprophy alcohol (95%). ii). Open the ADF unit and document cover as shown in Figure 6-2.Wipe the glass of flatbed area and ADF area by moving the swabfrom side to side. iii). Close the ADF unit and document cover. Your Sca...

Page 18 - TROUBLESHOOTING; Question and Answer

4-1 4. TROUBLESHOOTING The Scanner will automatically perform a simple self-test each time it isturned on. This will help spot major system errors in the Scanner itself. When the test is initiated, the READY LED is flashing. When the test iscompleted, if no error occur, the READY LED is steadily on....

Page 20 - Paper Jam in the ADF; In the event of paper jam, please follow the procedures below.

4-3 Question: The scanned image always comes out to be too dark. Answer: a) Use your application to modify the Gamma setting to 2.2 and1.8 for your printer and monitor respectively. b) Use Brightness setting from the TWAIN user interface to get a brighter image. Question: The Scanner works well othe...

Page 21 - Figure 4.2 ADF Paper Jam - Removing the Paper

Page 22 - SPECIFICATIONS; All specifications are subject to change without notice.; Paper with clip or staple attached

5-1 5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: ❖ Paper with clip or staple attached; ❖ Paper with ink not totally dry; ❖ Paper with inconsistent thickness, such as envelopes; ❖ Paper with wrinkles, curls, folds or tears; ❖...

Page 23 - Scanpartner 15C Specifications

5-2 5.1 Scanpartner 15C Specifications Scanner Type ❖ 1-pass colour ❖ Flatbed with ADF built-in Scanning Mode ❖ 30-bit colour ❖ Grey Scale (256 levels) ❖ Line Art/Halftone (64 levels) ❖ Error Diffusion (single bit) Optical Resolution ❖ 300 x 600 dpi in a dpi increments Light Source ❖ Cold Cathode fl...

Fujitsu 15C - Manual

Table of Contents:

Summary

Other Fujitsu Models