Franklin Submersible Well Pump - Manual
Franklin Submersible Well Pump – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – If test running pump before installation:; W A R N I N G
- Page 3 – SUITABILITY OF WELL; A safety cable to prevent loss of pump if pipe should; CHECK VALVES; Fluid draining back through the pump; FIGURE 1 - Installation Diagram; Poppet Assembly
- Page 4 – ELECTRICAL INFORMATION
- Page 5 – WELL TEST; Never run pump unless it’s completely; C A U T I O N
- Page 7 – responsibility of the purchaser.; the above may not apply to you.; made in connection with the sale of its products.; MAY VARY FROM STATE TO STATE.
- Page 9 – MANUEL DU PROPRIETAIRE; INSPECTION DE L’ÉQUIPEMENT; D A N G E R; ATTENTION; AVERTISSEMENT
- Page 10 – FIGURE 1 - Diagramme D’installation
- Page 12 – VÈRIFICATION DU PUITS; FIGURE 2 - Schéma Câblage Pompe
- Page 14 – GUIDE DE DÉPANNAGE; L’interrupteur de surcharge se déclenche.; INFORMATIONS IMPORTANTES POUR LINSTALLATEUR DE
- Page 15 – Franklin Pump Systems Inc.; produit a été installé originalement.; DROITS QUI PEUVENT VARIER D’UN ÉTAT À L’AUTRE.
OWNER'S MANUAL
4” and 6”
SUBMERSIBLE PUMPS
BEFORE INSTALLING PUMP, BE SURE TO READ
THIS OWNER’S MANUAL CAREFULLY.
Fill pump with water before starting
or pump will be damaged. The motor on this pump
is guaranteed by the manufacturer and in event of
failure it must be returned to an authorized service
station for repairs. Motor warranty is void if repairs
aren’t made by an authorized repair station.
INSPECT THE SHIPMENT
Examine the pump when it is received to be sure there
has been no damage in shipping. Should any be evident,
report it immediately to the dealer from whom the pump
was purchased. Please check the pump package to see
that it includes pump, motor, and motor leads (if your
pump purchase includes a motor).
C A U T I O N
READ AND FOLLOW SAFETY INSTRUCTIONS
This is the safety alert symbol. When you see
this symbol on your pump or in this manual, look
for one of the following signal words and be alert to the
potential for personal injury:
D A N G E R
warns about hazards that
will
cause
serious personal injury, death or major property damage
if ignored.
W A R N I N G
warns about hazards that
can
cause
serious personal injury, death or major property damage
if ignored.
C A U T I O N
warns about hazards that
will
or
can
cause minor personal injury or major property damage if
ignored.
The label
NOTICE
indicates special instructions, which
are important but not related to hazards.
Carefully read and follow all
safety instructions in this
manual and on pump.
Keep safety labels in good
condition.
Replace missing or damaged
safety labels.
Wire motor for correct
voltage. See “Electrical”
section of this manual and
motor nameplate.
Ground motor before
connecting to power supply.
Meet National Electrical Code, Canadian Electrical
Code, and local codes for all wiring.
Follow wiring instructions in this manual when
connecting motor to power lines.
Hazardous voltage.
Can shock, burn, or
cause death.
Ground pump before
connecting to power
supply. Disconnect
power before working
on pump, motor
or tank.
W A R N I N G
All 4” models willl include either a built-in or external
mounted check valve with the discharge head. 6”
models do not include a check valve, and will need to be
purchased separately. Example: Franklin Control Box for
Franklin motors. Make certain that your available voltage
corresponds to that of your motor.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION RECORDS It is good idea to keep an accurate record of your installation. Be sure to record the data below: * This Information is on your pump or motor tag. It will help us identify your pump in case of later inquiries. TEST RUNNING If test running pump before installation: 1. Insure tha...
1 To insure correct rotation of three phase units, brace pump shell securely and apply power momentarily by snapping line switch quickly on and off. If rotation is correct, reaction of the shell will be clockwise when viewed from pump discharge (that is, pump shaft will rotate counter clockwise). In...
2 secondary power lines; it is not effective against direct hits. 6. Mount the control box in an area protected from rain, snow, direct sunlight or other high temperatures as this may cause tripping of the overload protector. Also protect the control box from extreme cold (below 25 o F/-32 o C) as t...
