Fisher & Paykel WL1264P1 - User Manual

6 CONTROL PANEL 1 POWER Press to turn the washer ON/OFF . 2 Wash Cycles Turn the dial to select the desired cycle for your load. 3 Remote Press and hold to control washer from the Fisher & Paykel app when Wi-Fi is enabled. 4 Delay Start Press to delay start time. 5 Display Shows the following: z...

7 will illuminate when the LID LOCK is active. To unlock the lid at any time during the cycle, press . In some circumstances, there may be a delay before the lid can be opened, for safety reasons. Do not obstruct the lid lock slot. Do not try to disable the lid lock. Turn KEYLOCK on: After starting ...

8 FIRST USE All controls only require a gentle press to activate. For best results, avoid repeated interruptions to the cycle, such as pressing , and ensure all items are removed as soon as the cycle has finished. 1 2 4 3 Press to activate your washer. Select your desired wash cycle using the dial. ...

9 FIRST USE 1 1 1 To pause your washer during the cycle, press . To cancel a cycle or power the washer off at any time, press . During a cycle, the progress indicators will illuminate to show the stage of the cycle that is being performed. Pausing a cycle Cancelling a cycle Progress indicators

10 WASH CYCLES Wash cycle guide Your washer has a number of wash cycles to suit your needs. Selecting the most appropriate cycle for each wash load will help ensure you get the best wash result. CYCLE WASH DESCRIPTION MAX LOAD (KG) WASH TEMP SPIN SPEED Mixed A wash for mixed everyday loads including...

11 Washing bulky items The BULKY cycle takes special care of bulky items. Bulky garments and bedding wash most effectively when they can move freely. Ensure that there is sufficient room in the bowl for the load to move during the wash.When washing a single bulky item add a large beach towel to the ...

12 WASH PREPARATION Sorting Sort items according to colour, fabric type, and soil type. Wash fine, delicate fabrics separately from thick, heavy fabrics. Always separate coloured items from whites, especially when they are new. Colour run could be an issue if you wash items at higher temperatures. S...

13 WASH PREPARATION Auto Dose Where do I put my detergent? Open the cover of the Auto Dose dispenser and fill to ‘Max’ with liquid detergent. Close the cover. z Only liquid detergent must be used in the dispenser. z Do not fill past ‘Max’. z The amount of detergent dispensed per wash can be adjusted...

14 Fabric Softener Fabric softener should not be added when ECO option is selected or for a RINSE cycle. The softener will not be dispensed. If you wish to use fabric softener we recommend: z Using it sparingly. Measure it carefully to ensure you do not fill above the ‘Max’ level of the dispenser. z...

15 WASH MODIFIERS Once you have selected your wash cycle you may wish to change the default wash options. Press WASH TEMP to increase or decrease the wash temperature. Press WATER LEVEL to increase or decrease the water level. Water Level The washer defaults to AUTO for most cycles. If preferred, th...

16 WASH MODIFIERS Press WASH OPTIONS to select the desired wash modifier. Press WASH BOOST to select the desired wash modifier. Wash Options This option allows you to add a combination of SOAK and/or RINSE + to your cycle . Wash Boost This option allows you to add a combination of PRE WASH and/or WA...

17 WASH MODIFIERS Press DELAY START to cycle through the delay times. Press to start the countdown. When DELAY START has begun, the time will begin counting down.If DELAY START is paused, the indicator and remaining time will illuminate solidly. Delay Start The DELAY START option can delay the start...

18 AUTO DOSE Open the cover of the Auto Dose dispenser and fill to ‘Max’ with liquid detergent. Close the cover. When using AUTO DOSE, the amount of detergent dispensed can be increased or decreased if required. Refer to ‘Detergent adjustment’ for details. Ensure Auto Dose is set to AUTO . Liquid de...

19 FAVOURITES 1 2 3 4 Using the dial, select the desired wash cycle. Press and hold the desired wash modifier for 3 seconds. A long tone will sound and SET will display onscreen. Adjust the desired wash modifiers. Press for 3 seconds to save the selected settings. A long tone will sound to confirm s...

20 OPTION ADJUSTMENT MODE To enter Option Adjustment mode : After using your washer a number of times you may want to personalise some of the options to suit your wash needs. There are a number of pre-set options, which can be changed: z The wash temperatures, including changing COLD to CONTROLLED C...

21 OPTION ADJUSTMENT MODE Wash temperature adjustment COLD, WARM COLD , WARM and WARM HOT can be adjusted by increments of 1°C using the wash temperature adjustment feature. To adjust COLD further refer to ‘Controlled Cold’ over page. HOT will be set by the hot water supply temperature and cannot be...

22 OPTION ADJUSTMENT MODE Controlled Cold CONTROLLED COLD adds a small amount of hot water to the cold wash to raise the water temperature to approximately 20°C. This can be effective if your water supply temperature is very low or if the cold wash performance is not meeting your needs. 1 2 3 4 With...

23 OPTION ADJUSTMENT MODE Out of balance recovery If an out of balance load is detected, the washer will stop and try to redistribute the load. To adjust the number of times the washer attempts to re-fill, OUT OF BALANCE RECOVERY can be used. 1 2 3 4 With the washer on at the wall, but off at the di...

24 OPTION ADJUSTMENT MODE End of cycle beeps The beeps signalling the end of a cycle can be increased or decreased using the END OF CYCLE BEEPS adjustment menu. 1 With the washer on at the wall, but off at the display, press and hold and together for 3 seconds. oPAd will show on the display. 4 Press...

25 OPTION ADJUSTMENT MODE Factory reset Factory reset will clear any favourites saved by the user and any custom settings applied. 2 3 Select DELICATE using the dial. The display will show rSt . 1 With the washer on at the wall, but off at the display, press and hold and together for 3 seconds. oPAd...

26 Water efficient washing machines will save you money, but it is also worth thinking about energy use, recycling water and the environment. z Use ECO . z Use AUTO WATER LEVEL . z Wash larger loads instead of several smaller loads. z Reduce the wash temperature. z Follow instructions on the deterge...

27 WI-FI AND REMOTE Ensure the washer is powered on.Press and hold REMOTE and DELAY START until APP shows onscreen. will flash while connecting and will show as solid when connected.Follow the instructions in the app to complete the connection. Press and hold REMOTE for 3 seconds. will illuminate to...

28 CARE AND CLEANING Before you start cleaning your washer, ensure that it is disconnected from the power. Cleaning the control panel, topdeck and lid Use a soft damp cloth to wipe all surfaces, and wipe dry. Avoid using chemical or scouring cleaners, as these will damage the paint and plastic surfa...

29 CARE AND CLEANING Drum Clean It is important that you regularly clean the inside of your washer. Your washer has a DRUM CLEAN cycle designed for this purpose. We recommend the use of commercial washing machine cleaners only. Ensure the cleaner used is compatible with your waste water system, i.e....

30 CARE AND CLEANING Auto Dose Tank Clean If AUTO is not frequently used, detergent in the tank can become viscous, dry out and cause inaccurate dosing. Use the Tank Clean cycle when you experience poor cleaning performance. 2 1 3 After 7 minutes add 750ml of warm water to the Auto Dose dispenser as...

31 BEFORE YOU CALL FOR SERVICE User warnings Please read the following pages before you call for service.Your washer is capable of diagnosing its own problems. If your washer gives a musical series of beeps every 10 seconds it is telling you that it has a problem which you can solve using the checkl...

32 FAULT CODES If a continuous series of beeps sound, all the lights turn off on the control panel and a number appears on the display, a fault has occurred. The washer automatically enters this mode when there is a fault. To stop the beeps, touch any button then perform the following steps: 1 Turn ...

33 TROUBLESHOOTING Operating problems PROBLEM POSSIBLE CAUSES WHAT TO DO Washer not turning on Power not switched on at the wall. Switch the power on at the wall. Then press . Household power supply not working. Try plugging in another electrical appliance. Washer not filling with water when pressed...

37 TROUBLESHOOTING Wash problems PROBLEM POSSIBLE CAUSES WHAT TO DO Detergent residue Overloading the washer. Try reducing your load size. Incorrect detergent dosage. Try using less detergent. Check the detergent instructions. Cold ambient temperatures, cold washes and/or short agitation times may n...

38 MANUFACTURER’S WARRANTY These Manufacturer’s Warranties DO NOT cover A Service calls which are not related to any defect in the product. The cost of a service call will be charged if the problem is not found to be a product fault. For example: 1 Correcting the installation, eg removal of bottom p...

39 MANUFACTURER’S WARRANTY G Pick-up and delivery. H Transportation or travelling costs involved in the repair when the product is installed outside the Fisher & Paykel trained and supported service technician’s normal service area. Nothing in this Manufacturer’s Warranty is intended to, nor lim...

40 CUSTOMER CARE In New Zealand if you need service or assistance: Go online to our website and book a service or call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care Consultants. Toll Free: 0800 FP CARE or 0800 372 273 Email: [email protected] Website: fisherpaykel...

41 CUSTOMER CARE Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Suburb Town Country Registration Register your product with us so we can provide you with the best service possible. To register your product visit our website: fisherpaykel.com