Fisher & Paykel DD60DCW7 - User Manual

Page 2 - FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL

2 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL 1 PRODUCT & CABINETRY DIMENSIONS DD60DC(H)X7 DD60DC(H)W7 DD60DC(H)B7 DD60DCM7 PARTS SUPPLIED CAVITY PREPARATION MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE SECURE WITHOUT DRAWER REMOVAL RECOMMENDED METHOD (a) ALTERNATIVE METHOD...

Page 3 - Electrical shock hazard; IMPORTANT SAFETY INSTRUCTIONS!; Electrical Shock Hazard

3 SAFETY AND WARNINGS - ALL MODELS ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY 2a 2b WARNING! Electrical shock hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. This appliance must be earthed. In the event of a malfunction or breakdown, earthing ...

Page 4 - PARTS SUPPLIED - ALL MODELS

4 PARTS SUPPLIED - ALL MODELS 3a If the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 3.6 m. The kit is available from the nearest Fisher & Paykel Authorised Service Centre or our local web...

Page 5 - ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

5 ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS 3b Panel bracket (2) (attached to product ) Panel mounting screws (12) Toekickmountingscrews (5) Toekick mounting bracket (1) (A custom toekick panel of any material with thickness 9 - 19 mm can be screwed to the plastic toekick mounting bracket) In...

Page 6 - PRODUCT DIMENSIONS; Product dimensions

6 H K M N A O O I Side Plan G F J L B C E D 4 PRODUCT DIMENSIONS Product dimensions (mm) Classic Desig ner In te grate d Remote contr ol In te grate d Badge contr ols A overall height 1 of product 820-880 2 820-880 2 820-880 2 820-880 2 B overall width of product 599 599 599 599 C overall depth of p...

Page 7 - CABINETRY DIMENSIONS; Cabinetry dimensions

7 5 CABINETRY DIMENSIONS Plan Side P Q R S T Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard min. 2 mmclearance to adjacent cupboard door Cabinetry dimensions (mm) Classic Desig ner In te grate d Remote c ontr ol In te grate d Badge c ontr ols P inside height of ...

Page 8 - min. 8 mm ventilation gap; INTEGRATED MODELS ONLY - CUSTOM PANEL CALCULATIONS

8 The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The fi nal panel/cabinetry alignment is achieved by adjusting the feet: WIDTH OF ALL PANELS Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box belo...

Page 9 - CAVITY PREPARATION; Water Connection; Water softener models; BENCHTOP

9 7 CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). ¾ “ BSP (GB20) to suit flat washer. Kosher requirements Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your local rabbi in respect to kosher installations. Water Press...

Page 10 - MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE; Left hand side

10 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Drain hoses - 1800 mm Inlet hose - 1250 mm Power cord (excl. plug) - 1650 mm Drain hoses - 2000 mm Inlet hose - 1650 mm Power cord (excl. plug) - 1650 mm Left hand side Right hand side

Page 12 - FIT THE SUPPLIED TOEKICK PANEL; SECURE TO THE CABINETRY ON THE SIDES; OPTIONALLY SECURE TO THE CABINETRY ABOVE

12 13a FIT THE SUPPLIED TOEKICK PANEL (OPTIONAL FOR INTEGRATED MODELS) 3 4 6 8 5 7 9 1 2 19 19 Important! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similia...

Page 14 - REFIT THE DRAWER ONTO THE RUNNERS

14 x4 13b REFIT THE DRAWER ONTO THE RUNNERS 2 1 4 5 3 Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Ensure the release tabs on both sides are reset fully. Ensure the drawer is now rotated clockwise back. 11b To acc...

Page 20 - Dishwasher using sink trap with drain hose joiner; Dishwasher and Standpipe Ø 38; mm; CONNECT INLET HOSE TO COLD WATER; see

20 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 23 3 1 750-882.5 mm 2 * 1 2 38 mm max. 120 mm 750-882.5 mm * If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain hose s...

Page 21 - SAVE THESE INSTRUCTIONS

21 27 26 FINAL CHECKLIST TROUBLESHOOTING Check all parts are installed.Ensure that all panels and parts thereof are secure and final electrical tests have been conducted in accordance with local electrical regulations. Ensure product is level, securely fastened to the cabinetry and opens and closes ...

Fisher & Paykel DD60DCW7 - User Manual

Table of Contents:

Other Manuals for Fisher & Paykel DD60DCW7

Summary

Other Fisher & Paykel Dishwashers Models