Extron MTP 15HD RS - Manual
Extron MTP 15HD RS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
MTP 15HD RS Series • Setup Guide
This card provides quick start instructions for an experienced installer to set up and operate any of the MTP VGA video and RS‑232 transmission
systems.
Pre-installation — RS-232 Jumper
JMP1
JMP2
JMP3
Unjumpered for
One-way (Default)
Jumpered for
Two-way
The receiver’s RS‑232 circuits are factory‑set to be one‑way, transmitter to receiver. If the system has only one
receiver
, jumper JMP 1 on the main board can be set for two‑way communication as shown at right.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP transmitter and up to eight receivers
as required.
Step 2 — Transmitter Inputs
INPUT
Tx Rx
RS-232
MONITOR
•
Connect a computer (VGA) video source to the Input connector.
•
Connect a VGA monitor to the Monitor connector.
•
Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown below.
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected
RS-232
Device Pins
MTP
Pins
1 2 3 4 5 6 7 8
Insert Twisted
Pair Wires
Pins:
NOTE:
If you are using Enhanced Skew-Free™
A/V cable, use the TIA/EIA T568A standard only.
Pin
1
2
3
4
5
6
7
8
T568A
Wire Color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
T568B
Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Step 3 — TP Cables Between Units
•
Terminate a TP cable as shown at right. Connect it between the transmitter’s Output port and the
receiver’s Input port (both ends must match).
NOTE:
If the unit is labeled “C7,” only CAT 7 cable should be used.
•
For daisy-chaining,
connect up to eight TP cables between a receiver’s Buffered
Output port and a daisy‑chained receiver’s Input port.
OUTPUT
Tx Rx
RS-232
Step 4 — Receiver Outputs
•
Connect a VGA monitor to the Output connector.
•
Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown in step 2, above.
Step 5 — Receiver DIP Switches
•
H Sync and V. Sync switches
— Set these switches up for positive sync or down for negative sync.
ON
1 2 3 4 5 6
H SYNC
+
V SYNC
+
C SYNC
SOG
VIDEO
END UNIT
•
Composite Sync, (SOG), and Video switches
— Set these switches as shown in the following table to output the
indicated format.
Output Format
C Sync
SOG
Video
RGBHV
RGBS
RGsB
Component*
S‑Video*
Composite*
NOTE:
*
Input video format must match.
•
End Unit switch
— Set this switch up if either of the following is true:
•
The receiver being configured is the only receiver connected to the transmitter.
•
The receiver being configured is the last receiver in a daisy‑chained system.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
