Page 2 - Precautions; Safety Instructions • English; Instrucciones de seguridad • Español
Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may pres...
Page 3 - 注意; 声明; FCC Class A Notice
安全须知 • 中文 这个符号提示用户该设备用户手册中有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压，有触电危险。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解 所 有 安 全 和 使 用 说 明 。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或 追加设备，以避免危险。 警告 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必 须 使 用 有 地 线 的 供 电 系 统 供 电 ...
Page 5 - Universal Interface • Quick Start Guide; Quick Start Guide — RGB 201 R; xi; Internal Configuration
RGB 201 R xi Universal Interface • Quick Start Guide Quick Start Guide — RGB 201 R xi Step 1 Turn the equipment off and disconnect the equipment from the power source. Step 2 For positive or negative output sync (rather than sync following the input), RsGsBs video, or to clamp sync timing to back po...
Page 6 - Audio output; Balanced Audio; Unbalanced Audio; DIP switches; Switch; Remote connector; Remote Control
RGB 201 R xi Universal Interface • Quick Start Guide Quick Start Guide — RGB 201 R xi , cont’d Pin RS-232 Function 1 — 2 TX Transmit data (-) 3 RX Receive data (+) 4 — 5 Gnd Signal ground 6 — 7 — — 8 — — 9 — — — — — Female 5 1 9 6 Male 1 5 6 9 RGBHV R H G V B S RGBS R G S B V H S RGsB RsGsBs R G B V...
Page 7 - Universal Interface • Table of Contents; Chapter 1 • Introduction; Chapter 2 • Installation and Operation; Table of Contents
RGB 201 R xi Universal Interface • Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About this Manual ................................................................ 1-2 About the RGB 201 R xi ....................................................
Page 8 - Universal Interface• Table of Contents; Table of Contents, cont’d; Chapter 3 • Remote Control; Symbol definitions; Appendix • Reference Information; Cables; ii
RGB 201 R xi Universal Interface• Table of Contents Table of Contents, cont’d Chapter 3 • Remote Control .................................................. 3-1 Simple Instruction Set Control ...................................... 3-2 Host-to-interface communications ....................................
Page 9 - Universal Interface; Chapter One; Introduction; About this Manual
RGB 201 R xi Universal Interface 1 Chapter One Introduction About this Manual About the RGB 201 R xi Features
Page 10 - Universal Interface • Introduction; Extron; Interface
RGB 201 R xi Universal Interface • Introduction Introduction, cont’d Introduction About this Manual This manual contains information about the Extron RGB 201 R xi universal interface and on how to operate and configure it. About the RGB 201 R xi The RGB 201 R xi (figure 1-1) is an analog computer-vi...
Page 11 - Features
RGB 201 R xi Universal Interface • Introduction The interface is rack and furniture mountable and has an internal switching power supply for worldwide power compatibility. Features Flexible mounting options — The RGB 201 R xi can be rack mounted, mounted under a desk or podium, or mounted through a ...
Page 13 - Chapter Two; Installation and Operation
RGB 201 R xi Universal Interface 2 Chapter Two Installation and Operation Installation Overview Internal Configuration Mounting the Interface Rear Panel Connections and Switches Operation Troubleshooting
Page 14 - Universal Interface • Installation and Operation; Installation and Operation, cont’d
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d Installation Overview This is an overview of the installation process. You will find detailed installation and operation instructions in this chapter.To install and set up the RGB 201 R xi interface, fol...
Page 15 - Figure 2-1 — Opening the interface
RGB 201 R xi Universal Interface • Installation and Operation 2-3 Internal Configuration The interface is factory configured to output RGBHV or RGBS video whose sync follows the input and that is clamped to the back porch. The interface can be configured to output positive or negative sync, output R...
Page 16 - Figure 2-2 — Location of jumpers and DIP switches; Sync polarity jumpers
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d 2-4 1 ON 2 J22 J23 RS-232 Connector J11 1 2 3 1 1 1 SW2 Blue Red J28 J9 H SyncJ20 V Sync J21 Enable Sync Figure 2-2 — Location of jumpers and DIP switches Sync polarity jumpers The interface is factory c...
Page 17 - Video clamping jumper
RGB 201 R xi Universal Interface • Installation and Operation 2-5 Internal sync DIP switches (RsGsBs) The interface is factory configured to strip all sync signals from the red, green, and blue video input signals and to output horizontal and vertical sync separately(RGBHV) or as composite sync (RGB...
Page 18 - Tabletop placement
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d 2-6 Mounting the Interface The interface can be mounted on tabletops, under desks, through desks, or on racks, as described in this section. Tabletop placement For tabletop or desktop placement only, ins...
Page 19 - Through-desk mounting
RGB 201 R xi Universal Interface • Installation and Operation 2-7 4 . Insert the four wood screws into the pilot holes. Fasten each screw into the installation surface until just less than 1/4" of the screw protrudes. 5 . Align the installed screws with the slots in the mounting brackets, and pl...
Page 21 - Rack mounting; UL guidelines for rack mounting
RGB 201 R xi Universal Interface • Installation and Operation 2-9 Rack mounting UL guidelines for rack mounting The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of these products in a rack: 1 . Elevated operating ambient temperature — If the unit is insta...
Page 22 - Figure 2-5 — Rack mounting
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d 2-10 (2) 4-40 x 3/16" Screws Use 2 mounting holes on opposite corners False Front paneluses 2 front holes RG B 201R xi BOO ST LEVE L CON TRO L PEAK WITH ADS P TM CEN TERIN G Figure 2-5 — Rack mountin...
Page 23 - Rear Panel Connections and Switches; Input; Figure 2-7 — Audio input connector wiring; Buffered Monitor connector
RGB 201 R xi Universal Interface • Installation and Operation 2-11 Rear Panel Connections and Switches Figure 2-6 shows the rear panel of the RGB 201 R xi . AUDIO REMOTE 100-240 0.2A 50/60 Hz OUTPUTS INPUT R H G V B L/MONO R S DDSP SOG SERR V SYNC WIDTH BUFFERED MONITOR MONO AUDIO LEFT NO BACKLIGHT ...
Page 24 - Dip switches; Figure 2-8 — Wiring the audio output connector
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d 2-12 d BNC output connectors — Connect a coaxial cable between the display (projector or monitor) and these rear panel BNC connectors.For RGBHV ( separate H and V sync ) output, connect the cables to fiv...
Page 25 - The default for all DIP switches
RGB 201 R xi Universal Interface • Installation and Operation 2-13 f DIP switches — This bank of DIP switches is used to configure the interface. The switches control: • DDSP or ADSP • SOG (sync on green) • Serration pulses • Vertical sync pulse width • Mono or stereo audio • Backlight illumination....
Page 27 - Remote connector —; Connect an RS-232 device to this DB; Figure 2-9 — Remote connector pinout; AC power connector —; Connect a standard IEC AC power
RGB 201 R xi Universal Interface • Installation and Operation g Remote connector — Connect an RS-232 device to this DB 9 female connector (figure 2-9) for remote centering control. Software for RS-232 control is included with the interface. See chapter 3, Remote Control for details. Pin RS-232 Funct...
Page 28 - Troubleshooting; Front panel controls and indicators; Level and peaking controls
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d Operation Connect power cords and turn on the display and audio output devices (projectors, monitors, speakers), the interface, and the input device (computer). The system is ready for operation.The imag...
Page 29 - Centering controls
RGB 201 R xi Universal Interface • Installation and Operation • At the maximum level setting (the clockwise limit of this control), the interface outputs video at 1.45 volts p-p. Select a setting in the boost range (0.7 volts and above), to compensate for the decrease in signal level that occurs whe...
Page 30 - Centering memory
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d N The centering controls have no mechanical limits to rotation. When the minimum or maximum limit of the control is reached, LCD indicates the horizontal or vertical shift limit has been reached and the ...
Page 31 - If the image does not appear or there is no sound
RGB 201 R xi Universal Interface • Installation and Operation When a centering control reaches its minimum or maximum limit, the LCD displays MIN or MAX on the line below H-SHIFT or V-SHIFT.Once the centering controls are no longer active, the centering settings are saved, and the LCD displays the c...
Page 32 - If the interface does not respond to controls
RGB 201 R xi Universal Interface • Installation and Operation Installation and Operation, cont’d 4 . If the picture “hangs off” the edges of the screen, adjust the centering controls ( [ , { ). 5 . If the edges of the image seem to exceed their boundaries or if thin lines and sharp edges look thick ...
Page 33 - Chapter Three; Simple Instruction Set Control
RGB 201 R xi Universal Interface 3 Chapter Three Remote Control Simple Instruction Set Control Command/Response Tables for SIS Commands Control Software for Windows
Page 34 - Universal Interface • Remote Control; Remote Control, cont’d; Figure 3-1 — Remote connector pinout; Interface-initiated messages
RGB 201 R xi Universal Interface • Remote Control Remote Control, cont’d Remote Control 3-2 The interface’s rear panel Remote connector (Figure 3-1) can be connected to the serial port output of a host device, such as a computer or control system. Remote communications with the switcher are via Extr...
Page 35 - Error responses; ASCII to HEX Conversion Table
RGB 201 R xi Universal Interface • Remote Control Error responses When the interface receives a valid SIS command, it executes the command and sends a response to the host device. If the interface is unable to execute the command because the command is invalid or it contains invalid parameters, it r...
Page 36 - Universal Interface • Remote Contr; Remote Contr; Command/response table for SIS commands; Command; Vertical shift
RGB 201 R xi Universal Interface • Remote Contr ol Remote Contr ol, cont’d 3-4 Command/response table for SIS commands Command ASCII Command Response Additional description (host to switcher) (switcher to host) Horizontal shift Set horizontal shift X@ H Hph X@] Set horizontal shift value to X@ (rang...
Page 37 - Control Software for Windows; Installing the software; Figure 3-2 — RGB 201 Control program window
RGB 201 R xi Universal Interface • Remote Control 3-5 Control Software for Windows The included RGB 201 control program, graphical control software for Windows, offers another way to control the interface. The control software is compatible with Windows 3.1, 3.11, 95/98, and above. Installing the so...
Page 38 - Using the help system; For information about program features, you can access the help
RGB 201 R xi Universal Interface • Remote Control Remote Control, cont’d 3-6 Using the help system For information about program features, you can access the help program in any of the following ways:• From the Extron Electronics program group, double-click on the RGB 201 Help icon. • From within th...
Page 39 - Appendix; Reference Information; Specifications
RGB 201 R xi Universal Interface A Appendix Reference Information Specifications Included Parts Optional Accessories Cables
Page 40 - Universal Interface • Reference Information; Reference Information, cont’d; Video; unity gain; Video output; input level; Sync
RGB 201 R xi Universal Interface • Reference Information Reference Information, cont’d Reference Information A-2 Specifications Video Gain .................................................. 0.5V to 1.45V p-pBandwidth ....................................... 300 MHz (-3dB)Rise time ......................
Page 41 - Audio; level; Audio input; Extron’s Simple Instruction Set – (SIS
RGB 201 R xi Universal Interface • Reference Information A-3 Audio Gain ................................................... Unbalanced output: 0dB; Balanced output: +6dB Frequency response ....................... 20 Hz to 20 kHz, ±0.05 dBTHD + Noise ................................... 0.03% @ 1 kHz,...
Page 42 - General; internal, autoswitchable; Specifications are subject to change without notice.; These items are included in each order for a RGB 201 R; Included Parts
RGB 201 R xi Universal Interface • Reference Information Reference Information, cont’d A-4 General Input power .................................... 100VAC to 240VAC, 50/60 Hz, 18 watts, internal, autoswitchable Temperature/humidity .................. Storage -40° to +158°F (-40° to +70°C) / 10% to 9...
Page 43 - Optional Accessories; Accessories; Under-desk mounting bracket kit; Adapter cables with Audio
RGB 201 R xi Universal Interface • Reference Information A-5 Optional Accessories Accessories Part number Under-desk mounting bracket kit 70-077-01 Through-desk mounting bracket kit 70-077-02 1U rack shelf 60-190-01 3.5 mm stereo plug 10-306-01 Installation cable (bulk 14-conductor, non-plenum) 22-1...
Page 44 - BNC cables
RGB 201 R xi Universal Interface • Reference Information Reference Information, cont’d A-6 BNC cables Part number BNC-5 3’ HR 26-260-15 BNC-5 6’ HR 26-260-01 BNC-5 12’ HR 26-260-02 BNC-5 25’ HR 26-260-03 BNC-5 50’ HR 26-260-04 BNC-5 75’ HR 26-260-16 BNC-5 100’ HR 26-260-05 BNC-5 3’ HRP 26-378-01 BNC...
Page 45 - Extron’s Warranty
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will,...
