Page 2 - Precautions; Safety Instructions • English
Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may pres...
Page 3 - FCC Class A Notice
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte...
Page 4 - MP 101 Series • Table of Contents; Table of Contents; Chapter One • Introduction
i MP 101 Series • Table of Contents Table of Contents Chapter One • Introduction ................................................... 1-1 About this Manual .................................................................... 1-2 About the MP 101, MP 101 AAP, and MP 101 D .............. 1-2 Features ....
Page 5 - Chapter Four • MP 101 D; Power input; Chapter Five • Architectural Installation
ii MP 101 Series • Table of Contents Table of Contents 68-992-02 Rev. A 05 09 All trademarks mentioned in this manual are the properties of their respective owners. Chapter Four • MP 101 D ....................................................... 4-1 About the MP 101 D ...................................
Page 6 - Chapter One; Introduction; About this Manual
MP 101 Series 1 Chapter One Introduction About this Manual About the MP 101, MP 101 AAP, and MP 101 D Features
Page 7 - MP 101 Series • Introduction
1-2 MP 101 Series • Introduction Introduction About this Manual This manual contains information about the MP 101, theMP 101 AAP, and the MP 101 D microphone to line preamplifi ers and provides instructions on how to mount and operate these units. About the MP 101, MP 101 AAP, and MP 101 D The Extro...
Page 8 - Flexible mounting options; — The MP 101 can be mounted on; External international power supply; — The autoswitchable,
1-3 MP 101 Series • Introduction Flexible mounting options — The MP 101 can be mounted on a rack, on a table, or under furniture. The MP 101 AAP mounts into various Extron architectural products. The MP 101 D is wall mountable using standard, off-the-shelf mounting accessories. External internationa...
Page 9 - Chapter Two; Rear Panel Features
MP 101 Series 2 Chapter Two MP 101 Rear Panel Features Front Panel Features Mounting the MP 101 Adjusting the MP 101 Remote Control
Page 10 - Power; The power connector on the rear panel is orange however,; less; than the recommended
2-2 MP 101 Series • MP 101 MP 101 The Extron MP 101 is a high performance, microphone to line level audio preamplifi er. Rear Panel Features 2 1 3 5 4 POWER12V 0.5A MAX MIC INPUT REMOTE VOL/MUTE MP 101 MIC TO LINEPREAMPLIFIER 10V LINE OUTPUT Power input a Power — Plug the external 12 VDC power suppl...
Page 11 - Your MP 101 may have shipped with a blue captive screw; — This LED lights green to indicate that the unit is; Mic; — A 3-pin, captive screw connector for a standard; For unbalanced audio, ensure that the Phantom power
2-3 MP 101 Series • MP 101 Power Supply Output Cord Orange Captive Screw Connector 3/16" (5 mm) Max SECTION A–A Ridges Smooth A A Tie Wrap N Your MP 101 may have shipped with a blue captive screw plug. The blue connector does not have the extended tail or the included tie-wrap. C Do not tin the ...
Page 12 - Remote connection; CAUTION; Front Panel Features
2-4 MP 101 Series • MP 101 MP 101, cont’d Remote connection d Remote — An optional 3-pin, captive screw connector allows a wall mounted audio controller or MediaLink product to remotely control volume and mute levels for the MP 101 unit. See “Remote Control”, later in this chapter, for more informat...
Page 13 - Tabletop use
2-5 MP 101 Series • MP 101 Mounting the MP 101 There are many optional accessories for mounting the MP 101. They include the following: Projector mounting options • PMK 100 Mini Projector (part #70-217-01 ) • PMK 300 Multi-Product Projector (part #70-374-01 ) • PMK 350 Low Profi le Multi-Product Pro...
Page 14 - Rack installation; Install blank panels (included with part #
2-6 MP 101 Series • MP 101 MP 101, cont’d Rack installation The MP 101 can be rack mounted using either the VersaTools 19" 1U rack shelf (part # 60-190-20 ), basic VersaTools rack shelf (part # 60-604-20 ), a standard universal 1U rack shelf (part # 60-190-01 ), or a 1U basic rack shelf (part # ...
Page 15 - Back of the rack installation; ). This mounting option allows the MP 101 to be
2-7 MP 101 Series • MP 101 Use 2 mounting holes onopposite corners. (2) 4-40 x 3/16"Screws 1U Universal Rack Shelf Both front false faceplatesuse 2 screws. 1/4 Rack WidthFront FalseFaceplate 1/2 Rack WidthFront FalseFaceplate 1/8 Rack WidthFront FalseFaceplate Back of the rack installation The M...
Page 16 - Furniture
2-8 MP 101 Series • MP 101 MP 101, cont’d Outside Inside Furniture mounting In addition to using the MP 101 on a rack, you can mount it on furniture using the optional MBU Mini Under-Desk Mount Kit (part # 70-212-01 ). To use this option, do the following: 1. Remove the rubber feet if they were prev...
Page 17 - Adjusting the MP 101; condenser microphone; If there is a remote control connection, unplug it while
2-9 MP 101 Series • MP 101 b. At each mark, drill a 3/32" (2 mm) diameter pilot hole approximately 0.25" (6 mm) deep in the mounting surface. c. Insert provided #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until just less than 0.25" (6 mm) of the...
Page 18 - Remote Control; Remote connector wiring; Remote control options
2-10 MP 101 Series • MP 101 MP 101, cont’d Remote Control The wiring and control options described below pertain to all models in the MP 101 series. Remote connector wiring As shown below, Pin 1 is 10 VDC reference voltage. Pin 2 is volume control DC voltage; range is 0 to 10 V, where 0 V is mute an...
Page 19 - Chapter Three
MP 101 Series 3 Chapter Three MP 101 AAP Rear Panel Features Front Panel Features Adjusting the MP 101 AAP Mounting the MP 101 AAP Remote Control
Page 20 - — Plug the external 12 VDC power supply into this; Do not tin the stripped power supply leads before
3-2 MP 101 AAP MP 101 Series • MP 101 AAP The Extron MP 101 AAP is a high performance microphone to line level audio preamplifi er. The three models are two-space MP 101 AAPs in black, white, and RAL 9010 (Eurowhite). Rear Panel Features POWER 12V 0.2A MAX LINE OUTPUT REMOTE 10V VOL/MUTE ON OFF ON O...
Page 22 - Adjusting the MP 101 AAP
3-4 MP 101 AAP, cont’d MP 101 Series • MP 101 AAP 3-pin Female 2 3 1 b Mic Gain — A recessed, adjustable potentiometer defi nes the amount of input signal (between 25 and 72 dB) allowed into the preamp. This potentiometer is covered by a plastic cap to avoid tampering. To adjust the potentiometer, u...
Page 23 - Mounting the MP 101 AAP; Before mounting, the MP 101 AAP should be tested to
3-5 MP 101 Series • MP 101 AAP level that is free of distortion. N If there is a remote control connection, unplug it while adjusting the Mic Gain potentiometer. Replace the remote control when fi nished. 4. If there is minimal distortion, but greater volume is required, turn the Mic Gain potentiome...
Page 24 - is 10 VDC reference voltage.
3-6 MP 101 AAP, cont’d MP 101 Series • MP 101 AAP 4 . Repeat steps 1 through 3 to mount any other AAPs. Cover any openings in the faceplate with blank plates (provided). 5. If it was not done previously, adjust the MP 101 AAP from its rear panel. See the previous section, “Adjusting the MP 101 AAP” ...
Page 26 - Chapter Four
MP 101 Series 4 Chapter Four MP 101 D About the MP 101 D Rear Panel Features Front Panel Features Adjusting the MP 101 D Mounting the MP 101 D Remote Control
Page 27 - Plug the external 12 VDC power supply into this
4-2 MP 101 D MP 101 Series • MP 101 D About the MP 101 D The Extron MP 101 D provides the same features as the other MP 101 models in a convenient, Decora ® style wallplate. Like the MP 101 and MP 101 AAP, this mic to line preamplifi er can be remotely controlled via a VCM volume/mute control module...
Page 28 - Phantom power switch; Low Cut fi lter switch; Remote
4-3 MP 101 Series • MP 101 D N Do not tin the stripped power supply leads before installing the captive screw connector. Tinned wires are not as secure in the captive screw connectors and could pull out. W The two power cord wires must be kept separate while the power supply is plugged in. Remove po...
Page 29 - Active LED; Mute LED; — This LED lights red to indicate mute.; Mic Gain; — A recessed, adjustable potentiometer defi nes the; XLR mic input; — An XLR connector for a standard microphone
4-4 MP 101 D, cont’d MP 101 Series • MP 101 D Front Panel Features MIC IN ACTIVE MUTE 1 2 3 4 a Active LED — This LED lights green to indicate that the unit is receiving power. b Mute LED — This LED lights red to indicate mute. c Mic Gain — A recessed, adjustable potentiometer defi nes the amount of...
Page 30 - Adjusting the MP 101 D; Mounting the MP 101 D
4-5 MP 101 Series • MP 101 D 3-pin Female 2 3 1 Adjusting the MP 101 D Adjustment options for the MP 101 D are located on its rear panel (see “Rear Panel Features” in this chapter for details). Therefore, you must perform these adjustments before mounting into a wall. To adjust the MP 101 D, do the ...
Page 33 - Chapter Five; Architectural Installation; Installation Instructions
MP 101 Series 5 Chapter Five Architectural Installation Installation Instructions Preparing the Site and Installing the Wall Box
Page 34 - MP 101 Series • Architectural Installation; The MP 101 must be installed into an Underwriters; Preparing the Site and Installing the Wall Box; The template is not shown at full size. Pay attention to the
5-2 Architectural Installation MP 101 Series • Architectural Installation Installation Instructions Two versions of the MP 101 series, the MP 101 AAP and MP 101 D , can be mounted into furniture, a wall, or an Ackermann fl oor box. For specifi c mounting instructions for each model, see “Mounting th...
Page 35 - • If the MP 101 will be installed without a wall box
5-3 MP 101 Series • Architectural Installation • If the MP 101 will be installed without a wall box (using mud rings or fastening it directly to the wall or furniture), measure and mark the surface for the cutout area indicated in the template. 3. Cut out the material from the marked area. 4. Check ...
Page 36 - Architectural Installation, cont’d; • If
5-4 MP 101 Series • Architectural Installation Architectural Installation, cont’d • If the MP 101 AAP or MP 101 D are being installed in a two- or four-gang AAP plate, attach the wall box to the wall stud or furniture with nails or screws, leaving the front edge fl ush with the outer wall or furnitu...
Page 37 - Appendix A; and Accessories; Specifi cations
MP 101 Series A Appendix A Specifi cations, Part Numbers, and Accessories Specifi cations Included Parts Optional Accessories
Page 38 - Specifi cations, Part Numbers, and Accessories; MP 101 Series • Specifi cations, Part Numbers, and Accessories; Audio; with a 10 Hz to 80 kHz bandwidth fi lter); Audio input
A-2 Specifi cations, Part Numbers, and Accessories MP 101 Series • Specifi cations, Part Numbers, and Accessories Specifi cations Audio Gain ................................................ Adjustable, +25 dB to + 72 dBFrequency response ..................... 20 Hz to 20 kHz, ±0.1 dBTHD + Noise (wit...
Page 39 - General; Rack mount
A-3 MP 101 Series • Specifi cations, Part Numbers, and Accessories General External power supply ................. 100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 1 A, regulated Power input requirements ........... 12 VDC, 0.3 ATemperature/humidity ................ Storage: -40 to...
Page 41 - Included Parts; Included parts; or
A-5 MP 101 Series • Specifi cations, Part Numbers, and Accessories Included Parts These items are included with each MP 101 unit: Included parts Part number MP 101 Microphone to Line Preamplifi er 60-718-10 PS 121C: universal 12 VDCm, 1.0A 70-775-01 Three 3-pin, captive screw connectors One 2-pin, c...
Page 42 - Optional Accessories; Accessories Part
A-6 Specifi cations, Part Numbers, and Accessories MP 101 Series • Specifi cations, Part Numbers, and Accessories These items are included with each MP 101 D unit: Included parts Part number MP 101 D Microphone to Line Preamplifi er (one of the following two): Black or 60-822-12 White 60-822-22 Powe...
Page 43 - Appendix B; Dimensions and Template for; Dimensions
MP 101 Series B Appendix B Dimensions and Template for the MP 101 D Dimensions Template
Page 44 - Dimensions and Template; MP 101 Series • Dimensions and Template for the MP 101 D; Always check and go by the dimensions given in this
B-2 Dimensions and Template MP 101 Series • Dimensions and Template for the MP 101 D Dimensions N Always check and go by the dimensions given in this appendix. 2X .094± .005 2X .125 2X #6-32 UNC-2B .000 .622 1.095 1.455 2X 1.755 2.420 2.610 .150 2X .130 THRU .330 .000 .309 .528 2X .7 28 1.057 1.290 ...
Page 45 - Template; Cut-Out Template for the Extron; SURFACE
B-3 MP 101 Series • Dimensions and Template for the MP 101 D Template 4.50" (11.43 cm) Cut Out Line for Installing the Electrical Box Top Panel 2.79" (7.09 cm) MP 101 D Cut-Out Template for the Extron 2.24" (105 cm) 4.13" (57 cm) SURFACE CUT-OUT AREA FOR MOUNTING Location of MP 101 D...
Page 46 - Extron’s Warranty
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will,...
