Extron IN1604 DTP - Manual
Extron IN1604 DTP – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Step 3; HDBT position; Step 4; Wiring Details; Twisted Pair Recommendations; Pin Wire Color; Connector; Insert Twisted
- Page 3 – Audio Wiring; Front Panel Overview; Extron; Configuring IN1604 Series Scalers; Extron Product Configuration Software; Help File; RCA Connector
- Page 4 – SIS Commands; Command; Firmware Upgrades
1
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
IMPO
RTAN
T:
Refer to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
IN1604 Series • Setup Guide
The Extron IN1604 DTP and IN1604 HD Scaling Presentation Switchers are four input, HDCP-compliant video scalers that accept a wide variety
of audio and video formats. This guide allows an experienced user to set up and configure an IN1604 Series scaler. It covers how to perform basic
operations using the front panel controls and selected Simple Instruction Set (SIS
™
) commands.
NOTE:
For full installation, configuration, menus, connector wiring, and operation details, see the
IN1604 Series User Guide
, at
Installation
Rear Panel Features
HDMI
HDMI
HDMI
3
4
2
1 CONFIGURABLE
100-240V ~ 0.5 A MAX
50-60 Hz
REMOTE
AUDIO
INPUT
OVER TP
OUTPUT
TALLY OUT
CONTACT IN
HDBT
DTP
L
1
2
R
L
R
Tx Rx G
3
2
1
4 +V
1 2 3 4 G
Tx
Rx
Tx
G
Rx
RS-232
OUT
IN
RS-232 IR
SIG
OUT
LINK
B
C
E
F
G
I
K
L
M
D
A
IN1604 DTP
H
Power and Input Connections
Output Connections
Control Connections
A
AC power connector
B
Configurable analog 15-pin HD (VGA)
connector (input 1)
C
HDMI input connectors (inputs 2-4)
D
Unbalanced analog audio input connector
(input 1)
E
Balanced or unbalanced analog audio input
connector (input 2)
F
Balanced or unbalanced analog
audio output connector
G
TP output connector
(IN1604 DTP only)
H
TP output switch (IN1604 DTP only)
I
RS-232 and IR Over TP
connector (IN1604 DTP only)
J
HDMI output connector
(IN1604 HD only)
K
Contact closure connector
L
Tally connector
M
Remote RS-232 connector
Figure 1.
Rear Panel Features (IN1604 DTP Shown Left and Unique IN1604 HD Features Shown Right)
Mounting and Cabling
Step 1
—
Mount the device.
a.
Turn off or disconnect all equipment power sources.
b.
Mount the IN1604 Series scaler on top of a flat surface using the provided rubber feet, under a table using an optional mounting kit for
under-the-desk mounting, or to a rack shelf using an optional rack shelf-mounting kit.
Step 2
—
Connect inputs.
a.
Connect an analog video source (RGB, YUV, S-video, or composite) to the 15-pin HD (VGA) connector (see figure 1,
B
)
b.
Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (
C
).
c.
Connect an unbalanced analog audio source to the 3.5 mm, female TRS (tip-ring-sleeve) audio connector (
D
on
page 3 for more details.
d.
Connect a balanced or unbalanced audio source to the 5-pole captive screw connector (
E
). See
details.
HDMI
HDMI
3
HDMI
4
2
1 CONFIGURABLE
100-240V ~ 0.5 A MAX
50-60 Hz
AUDIO
OUTPUT
TALLY OUT
CONTACT IN
L
1
2
R
L
R
Tx Rx G
3
2
1
4 +V
1 2 3 4 G
RS-232
OUT
IN
HDMI
INPUT
REMOTE
HDMI
HDMI
3
HDMI
4
2
1 CONFIGURABLE
100-240V ~ 0.5 A MAX
50-60 Hz
AUDIO
L
1
2
R
R
R
L
R
R
R
OUT
IN
INPUT
J
K
M
L
IN1604 HD
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 IN1604 Series • Setup Guide (Continued) Step 3 — Connect outputs. a. Connect a balanced or unbalanced audio output device to the 5-pole captive screw connector ( F ). b. For the IN1604 DTP, set the HDBT/DTP switch ( H ) depending on the type of device to be connected to the TP output connector. HD...
3 RS-232 and IR Over TP Wiring (IN1604 DTP Only) To pass bidirectional serial command signals between the IN1604 DTP and a connected DTP or HDBaseT sink device, connect a control device to the three leftmost poles (Tx, Rx, and G) of the 5-pole captive screw connector. To transmit and receive IR sign...
4 68-2631-50 Rev. A 07 14 Extron Headquarters +800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000+1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673Inside Europe Only +31.33.453.4040+31.33.453.4050 FAX Extron Asia +65.6383.4400+65...
