Extron IN1508 - Manual
Extron IN1508 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Front Panel and Remote Control Controls and Indicators; Menu button —; Menu system operation; Setup; If no image can be seen on the display, use; Set output signal settings; Step 5 —; Power; EXTRON ELECTRONICS IN1508 SCALING PRESENTATION SWITCHER; INPUT
- Page 3 – Interlaced —; Aspect ratio setup; y = Video refresh rate
- Page 4 – from the same group; PIP Mode; Europe; Asia; Japan; Middle East; Low Resolution; NOTE
N
For full installation, configuration, and operation details, refer to the
IN1508 User ’s Manual, available at
www.extron.com
.
This guide provides quick start instructions for an experienced installer to set up and
operate the Extron IN1508 Scaling Presentation Switcher.
Installation and cabling
50/60Hz
100-240V 50-60Hz
I
N
P
U
T
VID
VID
YC
YC
Y
B-Y
R-Y
RGB
DVI
RS-232
1
2
4
5
3
L
1
2
3
4
5
6
7
R
AUDIO INPUT
8
L
A
B
R
OUTPUT
L
R
OUTPUT
RGB
Y, B-Y, R-Y
7
8
RGB
L I S T E D
1 T 2 3
I . T. E .
C
U S
6
2
5
9
8
4
3
1
6
12
11
7
10
Connections
a
AC power connector
g
Output 15-pin HD connector
b
Inputs 1 and 2 composite video BNC connectors
h
Audio Inputs 1 through 5 RCA connectors
c
Inputs 3 and 4 S-video mini-DIN connectors
i
Audio Inputs 6 through 8 3.5 mm mini stereo jacks
d
Input 5 component video BNC connectors
j
Audio Output A RCA connectors
e
Inputs 6 and 7 RGB video 15-pin HD connectors
k
Audio Output B captive screw connector
f
Input 8 DVI video connector (DVI-D only)
l
RS-232 9-pin D connector
Step 1 — Mounting
Turn off or disconnect all equipment power sources. For tabletop use, affix the rubber feet. For
optional rack mounting, secure the supplied brackets (see image at right) and mount in a rack.
Step 2 — Video inputs and output
a
.
Inputs 1 and 2
— Connect composite video
sources to these female BNC connectors.
b
. Inputs 3 and 4 — Connect S-video sources
to these 4-pin mini DIN connectors.
c
.
Input 5
— Connect a component video
(YUVi, YUVp, HDTV) source to these
female BNC connectors.
d
. Inputs 6 and 7 — Connect RGB video sources to
these 15-pin HD connectors.
e
.
Input 8
— Connect a single link of DVI-D video
to this DVI-I connector.
f
.
Output
— Connect an RGB or component video
display to this 15-pin HD output female connector.
Step 3 — Audio inputs and outputs
a
.
Audio Inputs 1 through 5 RCA connectors —
Connect stereo or mono audio sources.
b
. Audio Inputs 6 through 8 3.5 mm mini jacks — Connect computer
audio sources.
c
.
Output A RCA audio connectors —
Connect a stereo or mono audio
device (receiver, amplifier, or the like).
— OR —
Output B audio captive screw connector
— Connect a stereo or mono
audio device (receiver, amplifier, or the like); wire the connector as shown
at right.
68-791-50
Rev. A 04 10
IN1508 – Setup Guide
100-240V 50
-60H
z
I
N
P
U
T
VID
VID
YC
Y
B-Y
C-Y
RG
B
DV
I
1
2
4
5
3
L
2
3
4
5
6
7
R
AUDIO INPU
T
L
A
B
R
OUTPUT
L
R
OUTPUT
RG
B
Y, B-
Y, C-
Y
8
7
RG
B
6
L I S
T E
D
1 T
2 3
I . T
. E .
C
U S
I
N
P
U
T
VID
VID
1
2
YC
YC
4
3
YC
Y
B-Y
R-Y
5
RGB
7
RGB
6
DVI
8
L
1
2
3
4
5
6
7
8
R
AUDIO INPUT
L
A
B
R
OUTPUT
L
R
OUTPUT
RGB
Y, B-Y, R-Y
For unbalanced audio output, connect
the sleeve(s) to the ground contact.
DO NOT
connect the sleeve(s) to the
negative (-) contacts).
Unbalanced Stereo Output
Balanced Stereo Output
CAUTION
Tip
NO GROUND HERE.
Sleeve(s)
Tip
NO GROUND HERE.
Tip
Ring
Tip
Ring
L
R
L
R
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IN1508 • Setup Guide 2 IN1508 — Setup Guide (cont'd) Step 4 — RS-232 a . RS-232 — Connect a control system or computer to the rear panel RS-232 port. The IN1508 User's Manual, at www.extron.com details Simple Instruction Set (SIS ™ ) commands. Front Panel and Remote Control Controls and Indicators M...
3 IN1508 • Setup Guide Set up the display N You may need to first set the display's aspect ratio to 1:1, pixel for pixel, or "true" mode to eliminate overscan. Test patterns are available on IN1508 units that shipped after March 2007 and are firmware version 2.30 or higher. Earlier units may...
Inputs 6 and 7 setup RGB inputs 6 and 7 may need minor horizontal and vertical start, active pixels (horizontal), active lines (vertical), total pixels, and phase adjustments for best image quality. 1 . Press the Input button to select the input to be optimized. 2 . Execute the Auto-Image ™ function...
