Page 2 - CAUTION
Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation opening or slots on the cover. Do not drop metallic parts through slots.This could permanently damage the appliance. Turn the power off immediately and contact...
Page 4 - Important Safeguards
Important Safeguards Read Instruction ---All the safety and operating instructions should be read before the init is operated Retain Instructions ---The safety and operating instructions should be retained for future reference. Heed Warnings —All warnings on the unit and in the operating instruction...
Page 5 - Table of Contents
Table of Contents 1. Product Overview …………………………………….………………..…..…..Page 1 1.1 Main features………………………………………………………………….....…..….1 1.2 Specifications………………………………………………………………..…………..2 2. Back panel connections ……………………………………………......………3~4 3. System connection ………………………….………………………………………..5 Before instal...
Page 6 - Product Overview; channel real time audio recording capabilities
1. Product Overview The EDSR1600 Duplex Digital Video Recorder (DVR) a full-featured DVR designed specifically for use in security industry. The DVR incorporates all the benefits of digital video recording, is simple to install, and operates just like a VCR. Highly efficient compression technology a...
Page 7 - Specifications
Specifications 2 1.2 Specifications 9 (EDSR900) / 16 (EDSR1600) camera inputs (BNC),1Vp-p/75ohm 430mm (W) x 88mm (H) x 300 (D) Dimension AC100~240V Power Source 100W max. Power Consumption Video Input M-JPEG Video Compression 0 ° C ~ 40 ° C Operating Temperature 2 x RJ45 Socket RS485 9-pin female D-...
Page 8 - Back Panel Connections; power socket
Back Panel Connections 2. Back Panel Connections 1 ON/OFF: Main on/off switch. 2 AC100~240V power socket . 3 VIDEO IN: BNC-sockets for composite signal video inputs, automatic 75 Ohm termination 1 ~ 16. 4 VIDEO OUT: Loop through video outputs for each input channel.1 ~ 16) Matrix Outputs: These conn...
Page 9 - LAN Connector; D-Sub 9 pins connector to RS232 ports for remote control.
4 10 ALM-OUTPUT : Two-way contact relay alarm output. In normal condition, this N.C. contact shorted to ALM-COM. In alarm status, it is open between ALM-NC and ALM-COM, N.O. is shorted to ALM-COM. ALM-INPUT : Normally Open (N.O) or Normally Close (N.C) type alarm sensor input. The Alarm Input can be...
Page 10 - System Connection; Before Installation; Please refer to the following diagram for the system connections.; MAIN Monitor
System Connection 5 3. System Connection The installations described below should be made by qualified service personnel or system installers. Before Installation Please refer to the following diagram for the system connections. Matrix Outputs 4 CALL Monitors (Optional) EDSR 900: Camera 1~9 / EDSR-1...
Page 11 - Front Panel Keypads; SHUTTLE Ring and JOG Dial
Front Panel Keypads 4. Front Panel Keypads SHUTTLE : In Playback mode, turn the shuttle ring to fastforward/rewind the picture (600X maximum).In Pause mode, turn the shuttle dial to slow forward/rewindthe picture (1/32 maximum). JOG : In Pause mode, turn the jog dial to step forward/rewind the Pictu...
Page 13 - Operation; JOG; MENU
Operation 8 (1) Insert a HDD (IDE) for Video Storage (2) Connect cable for video/audio input and video/audio out, The detail connection is described in SYSTEM CONNECTION . (3) Switch Power On (4) Press MENU key to enter SET UP MENU. Once inside the main menu you will find there are 14 set up pages a...
Page 14 - MENU flow
MENU flow 6. MENU FLOW CLOCK ( See page 11 ) : 2003/07/04 FRI: 13:01:02 CLOCK SETTING MENU DATE TIME MENU LANGUAGE: ENGLISHVIDEO SYSTEM: NTSC VERSION: 0.96 11/23 TIMER SETTING MENU WEEK START STOP SPEED SET SUN 00:00 23:59 60 IPS OFFSUN 00:00 23:59 60 IPS OFFSUN 00:00 23:59 60 IPS OFFSUN 00:00 23:59...
Page 16 - ENTER
MENU 11 In CLOCK/LANGUAGE SETTING MENU , we define: (1) DATE : Current date, format: YYYY/MM/DD Year: 2000 ~ 2099, Month: 01~ 12, Date: 01~31, Week: Sunday~Saturday (2) TIME : Current time, format: HH:MM:SS Hour: 00 ~ 23, Minute : 00 ~ 59, Second: 00 ~ 59 (3) MENU LANGUAGE: ENGLISH (4) VIDEO SYSTEM ...
Page 17 - TIMER SETTING MENU; DLY
MENU 6.2 TIMER SETTING MENU 12 Timer records can be defined for 12 individual start and end times. (1) WEEK: This select the week day for the timer to record on schedule. DLY means daily record. (2) START: Enter the start time for timer recording. (3) STOP: Enter the end time for timer recording. NO...
Page 18 - Note: Sequences for Call monitors are defined in MATRIX menu.; In the SEQUENCE SETTING MENU, we define for MAIN Monitor
MENU (1) CH (Channel): Input channels. 1~16 EDSR-1600. (2) OP (Operation): ON includes the camera in the sequence, OFF skips the camera in the sequence. (3) DWELL (DWELL TIME) : Dwell Time is individual adjustable for each channel. The dwelling time for the sequencer can be set between 0-99 seconds....
Page 20 - Default setting is OFF for all cameras.
6.5 COVERT SETTING MENU COVERT SETTING MENU CH OP 1 OFF2 OFF3 OFF4 OFF5 OFF6 OFF7 OFF8 OFF9 OFF 10 OFF11 OFF12 OFF13 OFF14 OFF15 OFF16 OFF In COVERT SETTING MENU , we define: The covert setting menu allows you hide the desired camera on the display in a blue background. Change setting to ON for cove...
Page 21 - In ALARM RECORDING MENU, we define; ALARM RECORD SETTING MENU
In ALARM RECORDING MENU, we define (1) CH (Alarm input) : Select alarm input or RST for alarm reset input. (2) OP (OPERATION) : ON : Records when an alarm occurs. OFF : No reaction when alarms occur. (3) TYPE : Select alarm type: N.C. : Normally Closed with time out function counting from alarm star...
Page 22 - LOW; In the MOTION RECORD SETTING MENU, we define
MENU (1) CH (Channel) : Video input channel (2) OP (Operation) : Default: OFF ON: The device will respond recording when motion occurs. OFF: The device will not respond recording when motion occurs . (3) SEN (Sensitivity) : HIGH, MIDDLE or LOW adjustable. Default: MIDDLE. (4) DURATION: Duration time...
Page 25 - NETWORK SETTING MENU
6.9 NETWORK SETTING MENU IP ADDRESSNET MASK ADDRESSGATEWAY ADDRESSMAC ADDRESS USER-NAME PASSWORD LEVEL NETWORK SETTING MENU : 192.168.010.005: 255.255.255.000: 192.168.010.001: 00:5A:56:A3:87:1A GUEST--- GUEST--- GUEST--- GENERAL- GENERAL- GENERAL- SUPER--- SUPER--- SUPER--- (1) IP ADDRESS : Assign ...
Page 26 - In the CONTROL SETTING MENU, we define
MENU (1) RS232 BAUD RATE: There are 6 different speeds that can be used to transmit instruction or information through the RS232 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud, 19200 baud,and 3840 baud. The default setting from the factory is 9600 baud. (2) RS232 STOP BIT: Select stop b...
Page 27 - In BUZZER SETTING MENU, we define the buzzer; BUZZER SETTING MENU
In BUZZER SETTING MENU, we define the buzzer ON/OFF for following event: RECORD-IN, ALARM-IN, MOTION-IN, DISK FULL, VIDEO LOSS AND TIMER MENU 22 6.11 BUZZER SETTING MENU BUZZER SETTING MENU BUZZER : ENABLE RECORD-IN : ON ALARM-IN : ON MOTION-IN : ON DISK FULL : ON VIDEO LOSS : ON TIMER : ON Turn the...
Page 28 - ON
MENU 6.12 ARCHIVE SETTING MENU (1) PICTURE SIZE : Selects picture size for copying image to CF card: Large size: 720 x 576 PAL. Small size: 352 x 288 PAL. (2) TIME STAMP : ON : Shows the time stamp on the picture when copying image to CF card. OFF : This erases the time stamp on the picture when cop...
Page 30 - SYSTEM SETTING MENU
MENU 25 6.14 SYSTEM SETTING MENU (1) PLAY WITH AUDIO: AUDIO-1, AUDIO-2 ON/OFF: Play back with or without audio. (2) PLAY SPEED: Set the playback speed. Maximum 50 IPS PAL. (3) PASSWORD ENABLE: Enable/Disable the password protection. (4) PASSWORD: Set password with 6 digits (5) DISK USAGE: HDD-1, HDD...
Page 31 - INSTANT RECORDING; Recording
7.1 INSTANT RECORDING Press REC key to start continuous recording with setting of “NORMAL RECORD”. The recording rate and recording quality are set in the RECORD SETTING MENU. The LCD screen on the front panel of DVR will display as follows: Recording REC Press STOP key to stop recording. Since the ...
Page 32 - Playing Back
8.1 NORMAL PLAYBACK Press the PLAY key to start playing back the stored image/audio from the last SEGMENT. (1) Playback (2) Fast Forward/Reverse Playback During playing back, turn the SHUTTLE ring clockwise to start fast forward playing back. The speed will be shown on the screen at the bottom of th...
Page 33 - Search Playback
8.2 SEARCH PLAYBACK Press SEARCH key to enter the SEARCH MENU dialog. Search Playback SEARCH 28 SEGMENT SEARCH 0001 00020003 2003/04/24 19/03/29 HDD12003/04/25 12/30/30 HDD12003/05/20 12/00/00 HDD2 SEARCH MENU BY SEGMENT LISTBY ALARM LISTBY DATA TIME Turn the JOG dial to select BY SEGMENT LIST and p...
Page 36 - DATA EXPORT
DATA EXPORT Insert a Compact Flash card into the Compact Flash slot on the front panel of DVR.When inserting the Compact Flash card, make sure that insert direction is correct. NOTE: COPY function is not possible during RECORD. Stop recording to enable COPY function! Turn the JOG Dial clockwise to c...
Page 37 - COPY TO MOVIE FILE
COPY Press COPY key and then the copy menu and instruction appears. The main monitor switches to full screen display with following OSD: 32 Press the PLAY key to start playing back. PLAY 9.2 COPY TO MOVIE FILE CH01 COPY TO MOVIE FILE USE JOG TO SELECT PICTUREPRESS COPY TO START COPYPRESS PAUSE TO PA...
Page 38 - EXPORT EVENT LOG LIST
9.3 EXPORT EVENT LOG LIST DATA EXPORT This function allows to export the event log list to CompactFlash – Card.The generated text file in in *.txt format. DISPLAY Press „DISPLAY“ key and hold key for about 2 seconds. EVENT LOG TYPE ID TIME MOTION 2 2004/01/02 12:12:54 VL 1 2004/01/02 12:12:54 VL 3 2...
Page 39 - MONITOR VIEWS / OPERATION
MONITOR VIEWS / OPERATION 10. MONITOR VIEWS / OPERATION 10.1. MAIN MONITOR The EDSR900/1600 digital recorders provide 1 main monitor and 5 matrix monitors. These monitors have different functionalities: Main monitor: - Full screen and multi screen display: EDSR-1600: Full, 4, 6, 7, 9, 10, 13, 16, PI...
Page 41 - Installation example 2 remote operators, EDSR900; FUNCTION
RJ45 (RS485) pin assignment 11. REMOTE CONTROL 11.1 RS-485 REMOTE CONTROL The new standard EverFocus EDSR remote protocol allows challenging installations with DVR remote control at different installation sites.EDSR remote control is supported by the optional keyboards KS-KBJ (with 3-axis joystick a...
Page 42 - IR Remote Controller; Figure 1
IR Remote Controller The remote controller (RC-200, Figure 1) is an accessory to enhance the handy operations of the DVR. You can perform all the settings and operations by the remote controller. The effective distance is up to 10 meters without any obstacle. The keypad functions are same as the fro...
Page 43 - Basic Operations and Login Display:; (must be the same IP address as the one assigned to the; View From Internet/Intranet
12. View From Internet/Intranet Basic Operations and Login Display: Go to the Internet Explorer, key in the network IP address, for example, http://192.168.10.5 (must be the same IP address as the one assigned to the unit from the Network Setting Menu. You need a FIXED IP Address, please contact you...
Page 44 - Main Screen; STEP FORWARD
Main Screen Above diagram is the main screen display.The icons on the lower corner of the screen are mainly for control and Configuration, those on the right corner are for status indication.If any icon is grayed, it means that the specific function is not accessible in the current mode.The followin...
Page 45 - DATE TIME
10. The system allows up to 3 ways playback video, by SEGMENT, ALARM LIST and DATE TIME . 40 View From Internet/Intranet 40 (Playback by Date time) (Playback by ALARM LIST, click Refresh to show list) (Playback by SEGMENT LIST, click Refresh to show list)
Page 47 - LAN Functional Specification; Explorer / Netscape with JAVA support; max. 1,5 IPS depending on network conditions
Appendix-A LAN Functional Specification Specifications: Network Interface: 10Mbits/s Ethernet (10Base T)LAN controller Chip: RealTek 8019LAN Connector: RJ-45Protocol: HTTP,TCP/IP.ICMP,ARPRemote Access: Standard browser such as internet Explorer / Netscape with JAVA support Image Compression: JPEG Us...
Page 48 - When Recording with 160GB HDD; Time Lapse Mode Recording Time Table
Appendix-B When Recording with 160GB HDD 43 Lower Low Basic StandardHighSuperior : 15 kB: 19 kB: 23 kB: 27 kB: 31 kB: 35 kB (Estimated with typical image-low noise level) Time Lapse Mode Recording Time Table Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year NTSC Unit: Hour system storage(GB...
Page 49 - When Recording with 320GB HDD
When Recording with 320GB HDD Lower Low Basic StandardHighSuperior : 15 kB: 19 kB: 23 kB: 27 kB: 31 kB: 35 kB Appendix-B 44 (Estimated with typical image-low noise level) Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year NTSC Unit: Hour system storage(GB): 320 Recording Speed LOWER LOW BASI...
Page 50 - Appendix C: Serial Interface Specifications; Transmission setting; Serial Interface Specifications; The default setting from the factory is 9600 baud.
Appendix C: Serial Interface Specifications 2. Transmission setting PIN # NAME PIN # NAME 1 NOT CONNECTED 1 NOT CONNECTED 2 TXD 2 RXD 3 RXD 3 TXD 4 NOT CONNECTED 4 NOT CONNECTED 5 GROUND 5 GROUND 6 NOT CONNECTED 6 NOT CONNECTED 7 NOT CONNECTED 7 NOT CONNECTED 8 NOT CONNECTED 8 NOT CONNECTED 9 NOT CO...
Page 51 - Remote Control Protocol
3. Remote Control Protocol A computer or a terminal can be used to control the unit by sending the packet as following. 46 1-1. Sample control code packets Example1 : A packet that send "REC" key to DVR (ID=5) 0x85 (length) 0x00 (Receiver ID high byte) 0x05 (Receiver ID low byte) 0x4B (OPcod...
Page 56 - Alarm I/O pin assignment; DVR
Appendix-D 51 Alarm I/O pin assignment The alarm connector, Figure 1 , is used to provide one sensor alarm input for each camera input. For easy operation, an alarm extension board, Figure 2 , is provided to connect to the alarm connector. Each alarm input requires two wires, one wire connects to th...
