Page 2 - Control Panel
Control Panel Back button Menu button Load/remove paper button Power button and light Pause/cancel button Maintenance button Media feed button/cut button LCD display Help button CPD38235_Opera_SG_E.indd 2 10/16/12 10:24:07 AM
Page 3 - Contents
Contents Unpacking and Assembling the Printer .................................................................................................. 2 Assembling the Stand ...................................................................................................................... 3Mounting the...
Page 4 - U n p a c k i n g a n d A s s e m b l i n g t h e P r i n t e r; Unpacking and Assembling the Printer
2 | U n p a c k i n g a n d A s s e m b l i n g t h e P r i n t e r Unpacking and Assembling the Printer Note: Unless otherwise indicated, the illustrations in this manual show the SureColor ® T7000, but the instructions apply to all three models. Before beginning assembly, make sure you have suffic...
Page 5 - A s s e m b l i n g t h e S t a n d; The following items are included with your printer:; Assembling the Stand; Unpack the stand and make sure you have all of these items.
A s s e m b l i n g t h e S t a n d | 3 The following items are included with your printer: Assembling the Stand 1. Unpack the stand and make sure you have all of these items. Power cord Ink cartridges Legs Hex wrench Horizontal strut Paper basket Software and guides Printer Roll media adapter Baske...
Page 6 - Slide the horizontal strut into both of the legs as shown.
4 | A s s e m b l i n g t h e S t a n d 2. Slide the horizontal strut into both of the legs as shown. 3. Use the long end of the hex wrench to tighten the pre-placed screws on each side of the horizontal strut. 4. Lock the casters to fix the stand in place. (When moving the printer, unlock the caste...
Page 7 - M o u n t i n g t h e P r i n t e r o n t h e S t a n d; Mounting the Printer on the Stand
M o u n t i n g t h e P r i n t e r o n t h e S t a n d | 5 Mounting the Printer on the Stand You need at least two people (SureColor T3000) or four people (SureColor T5000/T7000) to install the printer and position it on the stand. When lifting the printer, only hold the areas shown below. Otherwis...
Page 8 - A t t a c h i n g t h e P a p e r B a s k e t; Attach the printer to the stand using three bolts.; Attaching the Paper Basket
6 | A t t a c h i n g t h e P a p e r B a s k e t 2. Attach the printer to the stand using three bolts. Attaching the Paper Basket The paper basket is a cloth sheet that attaches to the printer stand and catches your prints as they come out. You need the following parts to assemble and attach the pa...
Page 9 - Insert a plastic connector into one end of the square pole.
A t t a c h i n g t h e P a p e r B a s k e t | 7 2. Attach the stack guides to the bottom of the printer. Make sure each guide snaps securly into place. 3. Insert a plastic connector into one end of the square pole. 4. Slide the pole through the holes in the stack guides and attach the other plasti...
Page 10 - Use two bolts to fasten the arm in place.
8 | A t t a c h i n g t h e P a p e r B a s k e t 5. Attach the shorter arm to the inside of the basket holder on the left side of the printer. Use two nuts to hold the arm in place. 6. Use two bolts to fasten the arm in place. 7. Insert the longer arm into the rounded pole as shown.
Page 11 - Flip up the basket holder on the right side of the printer.
A t t a c h i n g t h e P a p e r B a s k e t | 9 8. Slide the pole through the basket cloth until it comes out the other end. The small hole in the cloth will be on the right side as shown below. 9. Flip up the basket holder on the right side of the printer. 10. Insert the end of the rounded pole i...
Page 12 - Use two nuts and two bolts to fasten the arm in place.
10 | A t t a c h i n g t h e P a p e r B a s k e t 11. Use two nuts and two bolts to fasten the arm in place. 12. On the back side of the printer, pull the paper basket up so that the stack guides fit into the slots as shown. Then, hook the loops around the pins on the back of the stack guides to ho...
Page 13 - C o n n e c t i n g t h e P o w e r C o r d; Connecting the Power Cord; Connect the power cord to the AC inlet on the side of the printer.
C o n n e c t i n g t h e P o w e r C o r d | 11 14. On the front side of the printer, slide the basket’s fabric all the way to the ends of the rounded pole as shown. Connecting the Power Cord 1. Unlock the casters. Then, move the printer to the place of use. (The casters are meant for moving the pr...
Page 14 - I n s t a l l i n g I n k C a r t r i d g e s; Installing Ink Cartridges; Unpack the ink cartridges and shake each 30 times (about 10 seconds).
12 | I n s t a l l i n g I n k C a r t r i d g e s Installing Ink Cartridges Use the ink cartridges that came with your printer for initial ink charging. During the initial installation process, it is normal for most of the ink in each cartridge to be used. 1. Turn on the power and configure the ini...
Page 15 - L o a d i n g R o l l P a p e r; Loading Roll Paper
L o a d i n g R o l l P a p e r | 13 4. Close the ink cover and wait for the ink to charge. The ink charging process takes about 22 minutes. Caution: Do not turn off the printer or open the ink cover when it is charging or you may waste ink. When the ink charging is completed, press and Load paper w...
Page 16 - Open the roll paper cover.
14 | L o a d i n g R o l l P a p e r 1. Open the roll paper cover. 2. Raise the roll lock lever. 3. Place the roll on top of the printer.
Page 17 - Release the tension lever on both adapters.
L o a d i n g R o l l P a p e r | 15 4. If necessary, adjust the roll media adapters to fit the core size of the roll paper. 5. Release the tension lever on both adapters. 6. Push the adapters into the paper core at both ends of the roll. Press the adapters in until they are fully inserted into the ...
Page 18 - Press the; Roll Paper; is highlighted in the display,; OK
16 | L o a d i n g R o l l P a p e r 8. Slide the roll paper all the way to the right until it lines up with the adapter guides. 9. Press the button on the control panel. Confirm that Roll Paper is highlighted in the display, then press the OK button. 10. Insert the end of the roll paper into the pa...
Page 19 - Lower the roll lock lever.; button. The paper will be fed into the
L o a d i n g R o l l P a p e r | 17 11. Pull the paper straight through until the leading edge reaches the front of the printer. 12. Lower the roll lock lever. 13. Following the instructions on the control panel, press the OK button. The paper will be fed into the printer.
Page 20 - Ready
18 | L o a d i n g R o l l P a p e r 14. Close the roll paper cover. 15. Check the message on the control panel. • If the paper type was automatically detected, the printer will display Ready on the LCD screen. The printer is ready to print. • If the paper type was not detected, the printer will dis...
Page 21 - P e r f o r m i n g a T e s t P r i n t; Performing a Test Print; Maintenance
P e r f o r m i n g a T e s t P r i n t | 19 Performing a Test Print You can print a nozzle check from the control panel and examine it to determine whether any nozzles are clogged or deflected. Then you can run a cleaning cycle if necessary. 1. Make sure the paper source and media type settings are...
Page 22 - A l i g n i n g t h e P r i n t H e a d; Aligning the Print Head; Installing Software; Connecting to Your System
20 | A l i g n i n g t h e P r i n t H e a d Aligning the Print Head Follow the steps below to align the print head using the printer’s control panel. Make sure the paper source and media type settings are correct for the type of paper loaded. 1. Confirm that the printer is ready to print. Press l o...
Page 23 - U p d a t i n g Y o u r P r i n t e r F i r m w a r e; Updating Your Printer Firmware; Checking the Current Firmware Version
U p d a t i n g Y o u r P r i n t e r F i r m w a r e | 21 To connect to a network hub or directly to your computer’s network interface, you need a standard RJ-45 CAT-6 network cable. 1. Plug the interface cable into the appropriate port on the printer. 2. Plug the other end of the cable into the ap...
Page 24 - U p d a t i n g t h e F i r m w a r e; Acquire Latest Information
22 | U p d a t i n g t h e F i r m w a r e 3. Click Acquire Latest Information to automatically download the latest firmware version for your printer from the internet. If there is a firmware update, the message “Found the latest firmware information. Do you want to download the firmware file?” appe...
