Epson 2100- Manual
Epson 2100– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Now the injector head can be moved from side to side by hand.; Step 1 Removing the Injector Lid
- Page 4 – Step 4 Tube Preparation
- Page 5 – stripped back; Step 6 Positioning the ink Bottles in the Tray
- Page 6 – UB; LK; PLEASE TAKE; Wing Adaptor
- Page 8 – . Push the injectors home; Fig. 15 Picture shows injectors fully; Step 10 Positioning The Foam Block
- Page 11 – YES; and continue printing in
- Page 13 – IMPORTANT; DO NOT; remove the injectors from the printer unless specifically; Removing; lift the inks above the Printer. This would cause the ink to flood
ECO-FLO CONTINUOUS INK SYSTEM
Perma
Jet
Assembly Instructions for
:
2100 Ink System
1
Epson 2100 Eco-Flo Shown
IMPORTANT
If your printer is new, set it up according to
the enclosed manufacturers instructions.
This is a check to ensure your new printer
and drivers are working correctly before the
Eco-Flo System is installed.
EPSON PRINTER
Epson 2100
Part No. A26421
.
It is very important you read these instructions carefully before you begin!
We will take you through the following steps:
1
Preparing your Injector
2
Setting up of the Inks in the bottle tray
3
Installation of the modified injector to your printer
4
Fitting of the Tube Supports System
5
Producing your first print.
Only start work on the installation once you have read the
instructions fully!
What you will need to Install the Eco-Flo 2100
•
Complete Eco-Flo 2100 Kit
•
Sharp Blade (Stanley Knife type) & Scissors
•
Measuring Tape or Ruler
•
Marking Pen or Pencil
•
Paper
Towels
Please read carefully before you continue
and
refer to the components diagram over the
page.
What is included in your Eco-Flo 2100 Kit
•
Injector Set with tubes attached
•
Set of 7 Inks & empty 100ml bottles
•
Black Tube Support Bracket with Hook &
Loop Fastener fitted
•
Bottle Holder Tray
•
Special Chip Block
•
1 Grey/White Tube Clip with adhesive pad
•
Installation Instructions and Profiles CD
•
10ml Syringe & wing adaptor
•
Pair of latex gloves
•
Special Foam Block
•
7 Tube Clamps
•
7 Bottle Caps & Clear Piping Tubes
Check List for components
Black Tube
Support Bracket
Set of 7
125ml Inks
Wing Adaptor
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Epson 2100
Summary
If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson injectors that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle patter...
Fig.2 Step 3 Bottle Preparation Locate the coloured bottle caps and straight lengths of plastic tubes. Insert the straight tube firmly into the bottom of each bottle cap see Fig.3 Fig.3 Step 4 Tube Preparation 4
Using a pair of scissors separate all tubes by snipping gently at the tube ends. Please see Fig.4 to the left. Fig.4 5 Strip back all the tubes by approx 150mm. Please note when assembling the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seate...
